Biomedical subjects

Kim L Gammelmark

Publications and source records attributed to Kim L Gammelmark.

3 recordsLinked to original sources

PubMed2007

In-vivo evaluation of convex array synthetic aperture imaging.

This paper presents an in-vivo study of synthetic transmit aperture (STA) imaging in comparison with conventional imaging, evaluating whether STA imaging is feasible in-vivo and whether the image quality obtained is comparable with traditional scanned imaging in terms of penetration depth, spatial resolution, contrast resolution and artifacts. Acquisition was performed using our research scanner RASMUS and a 5.5 MHz convex array transducer. STA imaging was acquired using circular wave emulation by 33-element subapertures and a 20 micros linear FM signal as excitation pulse. For conventional imaging, a 64 element aperture was used in transmit and receive with a 1.5 cycle sinusoid excitation pulse. Conventional and STA images were acquired interleaved, ensuring that the exact same anatomical location was scanned. Image sequences were recorded in real time and processed off-line. Seven male volunteers were scanned abdominally and the resulting images were compared by three medical doctors using randomized blinded presentation. Penetration and image quality were scored and evaluated statistically. Results showed slightly but significantly (0.48 cm, p = 0.008) increased penetration using STA. Image quality was also highly significantly (p < 0.001) increased. Results show that in-vivo ultrasound imaging using STA is feasible for abdominal imaging without severe motion artifacts.

Adult↗

PubMed2005

Ultrasound research scanner for real-time synthetic aperture data acquisition.

Conventional ultrasound systems acquire ultrasound data sequentially one image line at a time. The architecture of these systems is therefore also sequential in nature and processes most of the data in a sequential pipeline. This often makes it difficult to implement radically different imaging strategies on the platforms and makes the scanners less accessible for research purposes. A system designed for imaging research flexibility is the prime concern. The possibility of sending out arbitrary signals and the storage of data from all transducer elements for 5 to 10 seconds allows clinical evaluation of synthetic aperture and 3D imaging. This paper describes a real-time system specifically designed for research purposes. The system can acquire multichannel data in real-time from multi-element ultrasound transducers, and can perform some real-time processing on the acquired data. The system is capable of performing real-time beamforming for conventional imaging methods using linear, phased, and convex arrays. Image acquisition modes can be intermixed, and this makes it possible to perform initial trials in a clinical environment with new imaging modalities for synthetic aperture imaging, 2D and 3D B-mode, and velocity imaging using advanced coded emissions. The system can be used with 128-element transducers and can excite 128 transducer elements and receive and sample data from 64 channels simultaneously at 40 MHz with 12-bit precision. Two-to-one multiplexing in receive can be used to cover 128 receive channels. Data can be beamformed in real time using the system's 80 signal processing units, or it can be stored directly in RAM. The system has 16 Gbytes RAM and can, thus, store more than 3.4 seconds of multichannel data. It is fully software programmable and its signal processing units can also be reconfigured under software control. The control of the system is done over a 100-Mbits/s Ethernet using C and Matlab. Programs for doing, e.g., B-mode imaging can be written directly in Matlab and executed on the system over the net from any workstation running Matlab. The overall system concept is presented along with its implementation and examples of B-mode and in vivo synthetic aperture flow imaging.

Analog-Digital Conversion↗

PubMed2003

Synthetic elevation beamforming and image acquisition capabilities using an 8 x 128 1.75D array.

Ultrasound imaging can be improved with higher order arrays through elevation dynamic focusing in future, higher channel count systems. However, modifications to current system hardware could yield increased imaging depth-of-field with 1.75D arrays (arrays with individually addressable elements, several rows in elevation) through the use of synthetic elevation imaging. We describe synthetic elevation beamforming methods and its implementation with our 8 x 128, 1.75D array (Tetrad Co., Englewood, CO). This array has been successfully interfaced with a Siemens Elegra scanner for summed RF and single channel RF data acquisition. Individual rows of the 8 x 128 array can be controlled, allowing for different aperture configurations on transmit and receive beamforming. Advantages of using this array include finer elevation sampling, a larger array footprint for aberration measurements, and elevation focusing. We discuss system tradeoffs that occur in implementing synthetic receive and synthetic transmit/receive elevation focusing and show significant image quality improvements in simulation and phantom data results.

Algorithms↗