PubMed Health⌕ Search

Biomedical subjects

L J van Ruijven

Publications and source records attributed to L J van Ruijven.

12 recordsLinked to original sources
PubMed2002

A telemetry system to chronically record muscle activity in middle-sized animals.

Radio-telemetry enables the long-term recordings of biopotentials that may be obtained in freely moving animals without interference by the experimenter. The purpose of this study was to test a fully implantable device for: (1) its transmission range; (2) the characteristics of the transmitted signals; and (3) its actual application in long-term in vivo registration of EMG. Transmission range was tested by changing the device's position relative to the receiver. Computer simulation of the filtering characteristics provided comparison of original and transmitted signals. Implantation of the device in masticatory muscles, followed by analysis of telemetred signals and determination of activity levels allowed for examination of daily muscle use. The implant's transmission range covered the cage size for middle-sized animals with a minimum of signal dropouts. Transmitted signals were marked by (partial) loss of frequencies beyond 50 Hz, decreased amplitude and slightly delayed timing relative to original waveforms. Analysis of the transmitted EMG revealed that the device can be used for prolonged in vivo EMG registration, detection of peak activity levels, and the examination of general muscle use by the time spent at different levels of activity.

Animals↗
PubMed2002

Passive force characteristics of an architecturally complex muscle.

In architecturally complex muscles with large attachment areas, it can be expected that during movement different muscle regions undergo different amounts of length excursions. As a consequence, the amount of passive force produced by the regions will differ. Therefore, we tested the hypothesis that during movement the vector of the passive force of such a muscle, which defines the magnitude, position and orientation of the resultant force of the various regions, has no fixed position, between the muscle's center of origin and insertion. As a model for an architecturally complex muscle we used the masseter muscle. It was expected that during jaw opening anterior muscle regions are more stretched than posterior regions, leading to an anterior shift of the passive force vector. A three-component force transducer was used to measure both the position and magnitude of passive force in the masseter muscle of 9 rabbits. Forces were recorded during repeated cycles of stepwise opening and closure of the jaw. The muscle exhibited a clear hysteresis: passive force measured during jaw opening was larger than that during jaw closing. With an increase of the jaw gape there was an approximately exponential increase of the magnitude of the passive muscle force, while simultaneously the passive force vector shifted anteriorly. Moment arm length of passive force increased by about 100%. This anterior shift contributed substantially to the increase of the passive muscle moment generated during jaw opening. It can be concluded that in architecturally complex muscles the increase of the passive resistance moment which is associated with muscle lengthening might not only be due to an increase of the magnitude of passive muscle force but also to an increase of the moment arm of this force.

Animals↗
PubMed2002

Mechanical significance of the trabecular microstructure of the human mandibular condyle.

The human mandibular condyle has a parasagittal plate-like trabecular structure. We tested the hypothesis that this structure reflects the mechanical loading of the condyle. We developed a finite element model of the condyle to analyze the strains occurring during static compressive loading. The principal strains in the trabecular bone were primarily oriented in the sagittal plane. The first component was compressive and oriented supero-inferiorly. The second component was negligibly small and oriented medio-laterally. The third component was tensile, oriented antero-posteriorly, and almost equal to the compressive strain. This tensile strain was caused by antero-posterior bulging of the cortex. This means that the trabecular structure is also subjected to significant tensile forces. The orientation of the parasagittal strains followed the direction of the applied load. It was concluded that the trabecular structure of the mandibular condyle is optimal in resisting the compressive and tensile strains to which it is subjected.

Biomechanical Phenomena↗
PubMed2001

Three-dimensional finite element analysis of the cartilaginous structures in the human temporomandibular joint.

While the movability of the human temporomandibular joint is great, the strains and stresses in the cartilaginous structures might largely depend on the position of the mandible with respect to the skull. This hypothesis was investigated by means of static three-dimensional finite element simulations involving different habitual condylar positions. Furthermore, the influence of several model parameters was examined by sensitivity analyses. The results indicated that the disc moved together with the condyle in the anterior direction without the presence of ligaments and the lateral pterygoid muscle. By adapting its shape to the changing geometry of the articular surfaces, the disc prevented small contact areas and thus local peak loading. In a jaw-closed configuration, the influence of 30 degrees variations of the loading direction was negligible. The load distribution capability of the disc appeared to be proportional to its elasticity and was enhanced by the fibrocartilage layers on the articular surfaces.

Aged↗
PubMed2000

Three-dimensional finite element analysis of the human temporomandibular joint disc.

A three-dimensional finite element model of the articular disc of the human temporomandibular joint has been developed. The geometry of the articular cartilage and articular disc surfaces in the joint was measured using a magnetic tracking device. First, polynomial functions were fitted through the coordinates of these scattered measurements. Next, the polynomial description was transformed into a triangulated description to allow application of an automatic mesher. Finally, a finite element mesh of the articular disc was created by filling the geometry with tetrahedral elements. The articulating surfaces of the mandible and skull were modeled by quadrilateral patches. The finite element mesh and the patches were combined to create a three-dimensional model in which unrestricted sliding of the disc between the articulating surfaces was allowed. Simulation of statical joint loading at the closed jaw position predicted that the stress and strain distributions were located primarily in the intermediate zone of the articular disc with the highest values in the lateral part. Furthermore, it was predicted that considerable deformations occurred for relatively small joint loads and that relatively large variations in the direction of joint loading had little influence on the distribution of the deformations.

Aged↗
PubMed2000

The accuracy of joint surface models constructed from data obtained with an electromagnetic tracking device.

Electromagnetic tracking devices are widely used in biomechanics. In this article a method is evaluated to construct models of articular surfaces using an electromagnetic tracking device. First, the accuracy of the space tracker was examined and optimised. Then, from several joint surfaces random points were measured and eighth degree polynomials were fitted to these measurements. To check if the fit converged well, plots of cross sections of the model with corresponding data points were examined. The accuracy of the models was determined by comparing them with computed tomography data and by reproducibility tests. All the fits converged well to the data. The root mean square (RMS) error of the models varied from 0.07 to 0. 18mm, and was proportional to the size and complexity of the surface. This was mainly due to systematic errors made by the space tracker, which were also proportional to the size and complexity of the surface.

Biomechanical Phenomena↗
PubMed1999

Motor coordination in a multi-muscle system as revealed by principal components analysis of electromyographic variation.

The variation in electromyographic output of twelve trigeminal muscles of the rabbit was studied to test the hypothesis that they are under the control of a small number of independent neural factors. Jaw muscle electromyograms (EMGs) of eight animals were recorded in 95 chewing sequences, each consisting of 40-75 chewing cycles. The within-sequence correlations of the EMG burst amplitudes (integrated per cycle) and burst onsets were calculated between the muscles. The correlation matrix was subjected to a principal components analysis. This method aims at describing the variation in EMG amplitude and timing by means of the smallest possible set of newly defined variables, or principal components. Of the variation in EMG amplitude values of the twelve muscles, 75-90% could be accounted for by only three principal components. Each principal component was characterized by a group of muscles with high mutual positive correlations; they had zero correlation with other principal components. The first component represents the jaw closers: most of the bilateral masseter and the medial pterygoid muscles. The second represents the openers: the bilateral digastric and lateral pterygoid muscles. This demonstrates the tight control of both the jaw openers and closers, each by a single neural factor; these two factors are independent of one another. They most likely originate from the specific inputs from primary afferents to the opener and closer motoneurons. Unexpectedly, a third independent principal component appeared to control the closing activity of the non-chewing side, posterior deep masseter muscle. It was hypothesized that this muscle acts independently of the other closers to disengage the teeth and resets the jaw for a new chewing cycle. Principal components analysis of variation in timing of EMG onset revealed a grouping of all masticatory muscles in a single cluster, independent of EMG amplitude. This supports the hypothesis that timing and amplitude of masticatory EMG patterns are controlled independently.

Animals↗
PubMed1999

Fitting parametrized polynomials with scattered surface data.

Currently used joint-surface models require the measurements to be structured according to a grid. With the currently available tracking devices a large quantity of unstructured surface points can be measured in a relatively short time. In this paper a method is presented to fit polynomial functions to three-dimensional unstructured data points. To test the method spherical, cylindrical, parabolic, hyperbolic, exponential, logarithmic, and sellar surfaces with different undulations were used. The resulting polynomials were compared with the original shapes. The results show that even complex joint surfaces can be modelled with polynomial functions. In addition, the influence of noise and the number of data points was also analyzed. From a surface (diam: 20 mm) which is measured with a precision of 0.2 mm a model can be constructed with a precision of 0.02 mm.

Joints↗
PubMed1997

Electromyographic heterogeneity in the human temporalis and masseter muscles during dynamic tasks guided by visual feedback.

The complex architecture of the human jaw muscles suggests regional differences in function within these muscles. This study examines the way the temporalis and masseter muscle regions are activated when free mandibular movements with various speeds and against various external leads are carried out guided by visual feedback. Electromyographic (EMG) activity was registered in six temporalis and three masseter muscle regions with bipolar fine-wire electrodes. Recordings were made during open/close excursions, protrusion/retrusion movements, and laterodeviations. During open/close excursions and protrusion/retrusion movements, an anterior and posterior temporalis part could be distinguished, whereas during laterodeviations a more complex partitioning of this muscle was observed. During the protrusion/retrusion movements and the laterodeviations, the temporalis muscle demonstrated higher EMG peak activities than the masseter muscle, and within the masseter muscle the deep masseter showed higher EMG peaks than the superficial one. In contrast to this, during the open/close excursions the masseter showed higher peak activities than the temporalis muscle, while the superficial masseter showed higher EMG peak activities than the deep masseter. Within the deep masseter, differences were also found. During open/close excursions, the anterior deep region demonstrated higher EMG peak activities than the posterior region, whereas during protrusion/retrusion and laterodeviations the posterior deep region showed higher peaks. In general, speed had a greater effect on the EMG peak activity than external load. Only during laterodeviations did speed and load equally influence peak activity in both the deep and superficial masseter. During protrusion/retrusion movements, load showed no significant effect on EMG peak activity in the masseter muscle. A general finding was that, according to task, different regions were activated preferentially. This points to a partitioning of the excitatory command of the motoneuron pool.

Adult↗
PubMed1996

A new transducer system for direct motor unit force measurement.

A new transducer was developed for in situ measurement of the force vector in a complex muscle. The transducer measures the magnitude, and the line of action of a force in a single plane. The dynamic range of the transducer is 0-5 N. This range includes the small forces developed by an active motor unit and the relatively large passive force of a whole muscle. In this study we present the details of the transducer design and specifications, and describe its application in the measurement of motor unit forces of the rabbit masseter muscle.

Animals↗
PubMed1990

A new model for calculating muscle forces from electromyograms.

A muscle model is described that uses electromyogram (EMG), muscle length and speed of contraction to predict muscle force. Physiological parameters are the Hill constants and the shape of the twitch response to a single stimulus. The model was incorporated in a jaw model of the rabbit and tested by predicting the bite force produced by the jaw muscles during mastication. The time course of the calculated force appeared to match the bite force, measured in vivo by a strain gauge, applied to the bone below the teeth. The variation in peak strain amplitude from cycle to cycle correlated with the variation predicted by the model. The peak amplitude of the integrated EMGs of individual jaw muscles showed an average correlation with peak strain of 0.41. Use of the sum of the available peak amplitudes, weighted according to their effect upon the bite force increased the correlation to 0.46; the model predicted bite forces showed a correlation of 0.57 with the strain. The increase in correlation was statistically significant. The muscle forces were calculated using a minimum number of easily obtainable constants.

Animals↗