Biomedical subjects

Lauren Flynn

Publications and source records attributed to Lauren Flynn.

4 recordsLinked to original sources

PubMed2006

Decellularized placental matrices for adipose tissue engineering.

A tissue-engineered adipose substitute would be invaluable to plastic surgeons for reconstructive, corrective, and cosmetic procedures. This work involves the design of a scaffold for soft tissue augmentation incorporating the decellularized extracellular matrix (ECM) of human placenta. We have developed a protocol to decellularize an intact, large segment (8 cm by 8 cm) of the human placenta. To facilitate the complete decellularization of the dense matrix, a system was designed to perfuse the required chemicals into the placenta via the existing vasculature. Following processing, the original architecture of the placental ECM was preserved, including an intact vascular network. Histological, immunohistochemical, and scanning electron microscopic analyses confirmed the removal of the cells and cellular debris and characterized the composition and structure of the matrix. In vitro cell culture experimentation showed that the placental decellular matrix (PDM) could facilitate the adhesion of primary human adipose precursor cells at early time points. The PDM has great potential for use as a scaffold for adipose tissue engineering, as the placenta is a rich source of human ECM components that can be readily harvested without harm to the donor.

Adipose Tissue↗

PubMed2006

Biological skin substitutes for wound cover and closure.

In the past 30 years, the development and use of artificial skin in the treatment of acute and chronic wounds has advanced from an experimental concept to a working reality. However, while there have been an increasing number of artificial skin substitutes licensed for clinical use, they have yet to supplant the current gold standard of an autologous tissue graft for most applications. This article reviews the advantages and disadvantages of the currently available, biologically based substitutes, with special emphasis on their relative efficacy and suitability for treatment of particular wound types. Economic considerations, desirable improvements of currently available materials and the potential impact of future advances in the field will also be discussed.

Biocompatible Materials↗

PubMed2003

Fiber templating of poly(2-hydroxyethyl methacrylate) for neural tissue engineering.

We have developed a method to create longitudinally oriented channels within poly(2-hydroxyethyl methacrylate) (pHEMA) hydrogels for neural tissue engineering applications. Incorporated into an entubulation strategy, these scaffolds have the potential to enhance nerve regeneration after transection injuries of either the spinal cord or the peripheral nerve by increasing the available surface area and providing guidance to extending axons and invading cells. The fabrication process is straightforward and the resultant scaffolds are highly reproducible. Polycaprolactone (PCL) fibers were extruded and embedded in transparent, crosslinked pHEMA gels. Sonication of the pHEMA/PCL composite in acetone resulted in the complete dissolution of the PCL, leaving longitudinally oriented, fiber-free channels in the pHEMA gel. Regulating the size and quantity of the PCL fibers allowed us to control the diameter and number of channels. Small and large channel scaffolds were fabricated and thoroughly characterized. The small channel scaffolds had 142+/-7 channels, with approximately 75% of the channels in the 100-200 micro m size range. The large channel scaffolds had 37+/-1 channels, with approximately 77% of the channels in the 300-400 micro m range. The equilibrium water content (EWC), porosity and compressive modulus were measured for each of the structures. Small and large channel scaffolds had, respectively, EWCs of 55.0+/-1.2% and 56.2+/-2.9%, porosities of 35+/-1% and 40+/-1% and compressive moduli of 191+/-7 and 182+/-4kPa.

Acetone↗

PubMed2002

Manufacture of poly(2-hydroxyethyl methacrylate-co-methyl methacrylate) hydrogel tubes for use as nerve guidance channels.

Hydrogel tubes of poly(2-hydroxyethyl methacrylate-co-methyl methacrylate) (p(HEMA-co-MMA)) made by liquid-liquid centrifugal casting are being investigated as potential nerve guidance channels in the central nervous system. An important criterion for the nerve guidance channel is that its mechanical properties are similar to those of the spinal cord, where it will be implanted. The formulated p(HEMA-co-MMA) tubes are soft and flexible, consisting of a gel-like outer layer, and an interconnected macroporous, inner layer. The relative thickness of the gel phase to macroporous phase is controlled by the formulation chemistry, and specifically by the ratio of co-monomers, HEMA and MMA. By varying the surface chemistry of the mold within which the tubes are synthesized, tubes were prepared with either a "cracked" or a smooth outer morphology. Tubes with the cracked outer morphology had periodic channels that traversed the wall of the tube, which resulted in a lower modulus than smooth outer morphology tubes, yet likely greater diffusive permeability. For tubes (and not rods) to be formed, phase separation must precede gelation as is detailed in a formulation phase diagram for HEMA, MMA and water. The tensile elastic modulus of p(HEMA-co-MMA) tubes reflected the formulation chemistry, with greater moduli (up to 400 kPa) recorded for tubes having 10 wt% MMA. The p(HEMA-co-MMA) tubes therefore had similar mechanical properties to those of the spinal cord, which has a reported elastic modulus range between 200 and 600 kPa.

Biocompatible Materials↗