Biomedical subjects

Lee J Richter

Publications and source records attributed to Lee J Richter.

7 recordsLinked to original sources

PubMed2007

Measuring molecular order in poly(3-alkylthiophene) thin films with polarizing spectroscopies.

We measured the molecular order of poly(3-alkylthiophene) chains in thin films before and after melting through the combination of several polarized photon spectroscopies: infrared (IR) absorption, variable angle spectroscopic ellipsometry (SE), and near-edge X-ray absorption fine structure (NEXAFS). The data from the various techniques can be uniformly treated in the context of the dielectric constant tensor epsilon for the film. The combined spectroscopies allow determination of the orientation distribution of the main-chain axis (SE and IR), the conjugated pi system normal (NEXAFS), and the side-chain axis (IR). We find significant improvement in the backbone order of the films after recrystallization of the material at temperatures just below the melting temperature. Less aggressive thermal treatments are less effective. IR studies show that the changes in backbone structure occur without significant alteration of the structure of the alkyl side chains. The data indicate that the side chains exhibit significant disorder for all films regardless of the thermal history of the sample.

Algorithms↗

PubMed2006

Determination of lipid phase transition temperatures in hybrid bilayer membranes.

The main gel-to-liquid-crystal (LC) phase transition temperature, T(m), of the lipid monolayer in hybrid bilayer membranes (HBMs) was investigated using vibrational sum frequency spectroscopy (VSFS). In the gel phase, the acyl chains of the lipid molecules assume an ordered, all-trans configuration, whereas in the LC phase, the acyl chains exhibit a significant number of disordered gauche conformers. VSFS has unique sensitivity to the order/disorder transitions in the acyl chains and was used to determine T(m) for a series of saturated phosphatidylcholine lipids on octadecanethiolate self-assembled monolayers (SAMs). The values obtained for T(m) for all lipids studied are significantly higher than for the corresponding lipids in vesicles in solution. Additionally, the transition widths are broader for the lipids in HBMs. The underlying SAM clearly influences the phase behavior of the overlying lipid monolayer.

Journal Article↗

PubMed2006

Alkanethiols on platinum: multicomponent self-assembled monolayers.

We have studied the formation of self-assembled monolayers (SAMs) of n-alkanethiols on platinum thin films using X-ray photoelectron spectroscopy (XPS), reflection-absorption infrared spectroscopy (RAIRS), spectroscopic ellipsometry (SE), and contact angle (CA) measurements. Specifically, SAMs of 1-hexanethiol, 1-dodecanethiol, and 1-octadecanethiol were grown on polycrystalline Pt films, and the effects of Pt surface preparation, deposition conditions, and solvent treatments on the initial quality and stability of the monolayer in air were investigated. The SAMs prepared under ambient conditions on piranha-cleaned and UV/ozone-cleaned substrates were compared to monolayers formed on template-stripped Pt in an inert atmosphere. We found that alkanethiols deposited from 1 mM ethanolic solutions on piranha-cleaned Pt formed densely packed monolayers in which alkyl chains were oriented close to the surface normal. Stored in the laboratory ambient, these monolayers were unchanged over about 1 week but were largely oxidized in about 1 month. No evidence was found of molecules being weakly bound within the monolayer or having undergone C-S bond scission; however, three distinct sulfur states were observed for all samples in the XPS of the S 2p region. The lowest- and highest-binding-energy components are assigned to alkylthiolate and partially oxidized alkylthiolate species, respectively. The remaining S 2p component (approximately one-third of the sulfur layer), intermediate in binding energy between the other two components, is attributed to a chemisorbed species with a S binding configuration distinct from the majority alkylthiolate: for example, S bound to Pt bound to O, S with a different Pt coordination number, or S in an adsorbed disulfide.

Journal Article↗

PubMed2006

Broadband coherent anti-Stokes Raman spectroscopy characterization of polymer thin films.

Broadband coherent anti-Stokes Raman spectroscopy (CARS) is demonstrated as an effective probe of polymer thin film materials. A simple modification to a 1 kHz broad bandwidth sum frequency generation (SFG) spectrometer permits acquisition of CARS spectra for polymer thin films less than 100 nm thick, a dimension relevant to organic electronic device applications. CARS spectra are compared to the conventional Raman spectra of polystyrene and the resonance-enhanced Raman spectra of poly(3-hexylthiophene). The CARS spectra obtained under these conditions consistently demonstrate enhanced signal-to-noise ratio compared to the spontaneous Raman scattering. The sensitivity of the CARS measurement is limited by the damage threshold of the samples. The dielectic properties of the substrate have a dramatic effect on the detected signal intensity. For ultrathin films, the strongest signals are obtained from fused silica surfaces. Similar to surface-enhanced Raman scattering (SERS), Au also gives a large signal, but contrary to SERS, no surface roughening is necessary.

Algorithms↗

PubMed2005

Electrical and spectroscopic characterization of metal/monolayer/Si devices.

A simple technique for vibrational spectroscopy of metal/monolayer/silicon structures is applied to study the interaction of Au, Al, and Ti with alkane monolayers, either assembled onto thin oxides or directly attached to Si. The results are correlated with current-voltage and capacitance-voltage measurements. Alkane films on oxides are found to be robust with respect to the deposition of Au and Al and are partially consumed during the deposition of Ti. In contrast, alkoxy films directly attached to H-terminated Si via an ether linkage are displaced by all three metals. The vibrational data are positively correlated with the electrical data to establish an improved understanding of the interactions at the buried metal/monolayer interface. The results demonstrate extreme sensitivity of the monolayer/metal reactivity to the nature of the film/substrate bonding.

Journal Article↗

PubMed2005

Comparison of Si-O-C interfacial bonding of alcohols and aldehydes on Si(111) formed from dilute solution with ultraviolet irradiation.

Aliphatic alcohols and aldehydes were reacted with the Si(111)-H surface to form Si-O-C interfacial bonds from dilute solution by using ultraviolet light. The resulting monolayers were characterized by using transmission infrared spectroscopy, spectroscopic ellipsometry, and contact angle measurements. The effect of different solvents on monolayer quality is presented. The best monolayers were formed from CH(2)Cl(2). The optimized monolayers were thoroughly characterized to determine the film structure and monolayer stability. The UV-promoted, alcohol-functionalized, and aldehyde-functionalized monolayers are of comparable quality to those previously prepared by other means. Although both molecules are tethered through a Si-O-C bond, the film reactivity is distinctly different with the aldehyde films being more chemically resistant. The differences in chemical reactivity, vibrational spectra, hydrophobicity, and ellipsometric thickness between the alcohol and aldehyde monolayers are attributed to a difference in molecular coverage and monolayer formation.

Journal Article↗

PubMed2004

Structural and chemical characterization of monofluoro-substituted oligo(phenylene-ethynylene) thiolate self-assembled monolayers on gold.

Monolayers of oligo(phenylene-ethynylene) (OPE) molecules have exhibited promise in molecular electronic test structures. This paper discusses films formed from a novel molecule within this class, 2-fluoro-4-phenylethynyl-1-[(4-acetylthio)phenylethynyl]benzene (F-OPE). The conditions of self-assembled monolayer (SAM) formation were systematically altered to fabricate reproducible high-quality molecular monolayers from the acetate-protected F-OPE molecule. Detailed characterization of the F-OPE monolayers was performed by using an array of surface probes, including reflection absorbance infrared spectroscopy (RAIRS), contact angle (CA) measurements, spectroscopic ellipsometry (SE), X-ray photoelectron spectroscopy (XPS), ultraviolet photoelectron spectroscopy (UPS), and atomic force microscopy (AFM). XPS and RAIRS established that the SAM formed without removal of the F substituent and without oxidation of the thiol. The monolayer thickness, determined from SE and AFM based nanolithography, was consistent with the formation of a densely packed monolayer. The valence electronic structure of the SAM was consistent with an aromatic structure shifted by the electron-withdrawing fluorine substituent and intermolecular coupling within an oriented array of molecules.

Journal Article↗