Biomedical subjects

M A Dubé

Publications and source records attributed to M A Dubé.

5 recordsLinked to original sources

PubMed2006

Biodiesel production using a membrane reactor.

The immiscibility of canola oil in methanol provides a mass-transfer challenge in the early stages of the transesterification of canola oil in the production of fatty acid methyl esters (FAME or biodiesel). To overcome or rather, exploit this situation, a two-phase membrane reactor was developed to produce FAME from canola oil and methanol. The transesterification of canola oil was performed via both acid- or base-catalysis. Runs were performed in the membrane reactor in semi-batch mode at 60, 65 and 70 degrees C and at different catalyst concentrations and feed flow rates. Increases in temperature, catalyst concentration and feedstock (methanol/oil) flow rate significantly increased the conversion of oil to biodiesel. The novel reactor enabled the separation of reaction products (FAME/glycerol in methanol) from the original canola oil feed. The two-phase membrane reactor was particularly useful in removing unreacted canola oil from the FAME product yielding high purity biodiesel and shifting the reaction equilibrium to the product side.

Bioreactors↗

PubMed2003

Interactions of corneal cells with transforming growth factor beta 2-modified poly dimethyl siloxane surfaces.

The downgrowth of corneal epithelial cells at the interface of an artificial cornea and the host eye tissue poses a significant problem to be overcome in developing a successful implant. As a means of inhibiting the proliferation of corneal epithelial cells on the stromal surface of the implant, we examined the immobilization of transforming growth factor beta-2 (TGF-beta2) via a bifunctional poly ethylene glycol (PEG) spacer to poly dimethyl siloxane (PDMS) surfaces. Growth factor immobilization was confirmed by modification with (125)I-labeled TGF-beta 2. The modified surfaces were also characterized by advancing water contact angles, X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). Although the amount of growth factor covalently bound to the surface was difficult to quantify apparently due to strong interactions between the growth factor and the PEG layer and high levels of adsorption, differences in the modified surfaces, suggestive of the presence of a significant amount of TGF-beta 2, were found. In vitro interactions of the modified surfaces with human corneal epithelial and stromal cells were examined. Growth factor surface concentrations as well as culture in the absence and presence of serum and other adhesive proteins were examined. Corneal stromal and epithelial cells cultured on the TGF-beta 2-modified surfaces consistently gave results opposite to those expected. Likely, the most notable and surprising result was the almost complete lack of adhesion of the stromal cells, with coverage averaging between 3 and 5%. In comparison, corneal epithelial cell growth appeared to be promoted by the presence of the immobilized growth factor, with cell coverage averaging 50-60% at 7 days of culture. A TGF-beta 2 concentration effect was noted with both cell types in the absence of serum, with increases in the coverage at higher TGF-beta 2 concentrations. The observed cell growth appeared to be the result of interactions between the cells and active growth factor, because the addition of anti-TGF-beta 2 to the culture medium reduced cell coverage to levels similar to those noted on control surfaces. Therefore, although TGF-beta 2-modified surfaces may not be suitable as corneal epithelial cell inhibiting surfaces, interactions of surface immobilized growth factor and corneal cells are complex and should be further examined.

Biocompatible Materials↗

PubMed2003

Biodiesel production from waste cooking oil: 1. Process design and technological assessment.

Four different continuous process flowsheets for biodiesel production from virgin vegetable oil or waste cooking oil under alkaline or acidic conditions on a commercial scale were developed. Detailed operating conditions and equipment designs for each process were obtained. A technological assessment of these four processes was carried out to evaluate their technical benefits and limitations. Analysis showed that the alkali-catalyzed process using virgin vegetable oil as the raw material required the fewest and smallest process equipment units but at a higher raw material cost than the other processes. The use of waste cooking oil to produce biodiesel reduced the raw material cost. The acid-catalyzed process using waste cooking oil proved to be technically feasible with less complexity than the alkali-catalyzed process using waste cooking oil, thereby making it a competitive alternative to commercial biodiesel production by the alkali-catalyzed process.

Catalysis↗

PubMed2003

Biodiesel production from waste cooking oil: 2. Economic assessment and sensitivity analysis.

The economic feasibilities of four continuous processes to produce biodiesel, including both alkali- and acid-catalyzed processes, using waste cooking oil and the 'standard' process using virgin vegetable oil as the raw material, were assessed. Although the alkali-catalyzed process using virgin vegetable oil had the lowest fixed capital cost, the acid-catalyzed process using waste cooking oil was more economically feasible overall, providing a lower total manufacturing cost, a more attractive after-tax rate of return and a lower biodiesel break-even price. On the basis of these economic calculations, sensitivity analyses for these processes were carried out. Plant capacity and prices of feedstock oils and biodiesel were found to be the most significant factors affecting the economic viability of biodiesel manufacture.

Biotechnology↗

PubMed2002

Novel dendrimer based polyurethanes for PEO incorporation.

A series of segmented polyurethanes based on methylene diisocyanate/poly (tetramethylene oxide) and chain extended with either ethylene diamine or butane diol in combination with a generation 2 polypropylenimine octaamine dendrimer were synthesized. For polymer synthesis, the dendrimers were protected with either t-boc or Fmoc groups and were incorporated into the polyurethane microstructure to permit further functionalization with biologically active groups. Following deprotection, the dendrimers were reacted with succinimidyl propionate polyethylene oxide (SPA-PEO) to improve the protein resistance of the polymers and to examine the potential of this technique for polymer functionalization. Different synthesis techniques were examined to optimize the incorporation of the PEO into the polymer microstructure. Incorporation of the dendrimers and the PEO were confirmed by NMR and FTIR. Gel permeation chromatography was used to examine the molecular weights of the various polyurethanes. The dendrimer incorporated polymers had significantly lower molecular weights than the ED or BDO chain extended controls, likely due to lower reactivity of the dendrimers as a result of steric factors. Following PEO reaction, the molecular weights of the resultant polymers were consistent with the levels of PEO incorporation noted by comparison of peak intensities in the NMR spectra. Due to the highly hydrophilic nature of the PEO, some migration to the polymer surface was expected. Water contact angles and XPS, used to characterize the surfaces, suggest that there was some PEO enrichment at the surface of the polymers. Adsorption of radiolabeled fibrinogen to the polymer surfaces was decreased by a factor of approximately 40% in some of the PEO incorporated polymers. There were also differences in the patterns of plasma protein adsorption on the various surfaces as evaluated by SDS PAGE and immunoblotting. Therefore, the use of dendrimers in biomaterials for incorporation of a large number of functional groups seems to be promising.

Biocompatible Materials↗