Biomedical subjects

M B Talawar

Publications and source records attributed to M B Talawar.

At least 19 recordsLinked to original sources

PubMed2006

Synthesis, characterization and thermolysis studies on new derivatives of 2,4,5-trinitroimidazoles: potential insensitive high energy materials.

This paper reports the synthesis of three new derivatives of 2,4,5-trinitroimidazole namely, 1-methyl-2,4,5-trinitroimidazole (III), 1-carboethoxy-2,4,5-trinitroimidazole (V) and 1-picryl-2,4,5-trinitroimidazole (VII). The title compounds (III) and (V) were synthesized by the nitration of 1-methyl-/1-carboethoxy-(2,4,5-triiodoimidazole) (II and IV) with fuming nitric acid at 0 degrees C and (VII) was synthesized by condensation of 2,4,5-triiodoimidazole (I) with picryl chloride to obtain 1-picryl-2,4,5-triiodoimidazole (VI) followed by its nitration with fuming nitric acid at 0 degrees C. The synthesized compounds have been characterized by elemental analysis, spectral and thermal techniques. The thermolysis studies using TG-DTA revealed exothermic decomposition of the nitroimidazoles (III, V and VII) with T(max) in the temperature range of 196-225 degrees C. The energy of activation obtained for these compounds was in the range 150-170 kJ/mol. The sensitivity data obtained for the newly synthesized compounds (III, V and VII) indicated their safe nature towards external stimuli (h(50%)>100 cm; friction>36 kg) and could be potential candidates for low vulnerable applications in the futuristic systems. The theoretically predicted performance parameters suggest that 1-methyl-2,4,5-trinitroimidazole (III), exhibits higher velocity of detonation (VOD: 8.8 km/s) compared to compounds V and VII (VOD: 7.6 and 8.41 km/s, respectively).

Calorimetry, Differential Scanning↗

PubMed2006

Method for preparation of fine TATB (2-5 microm) and its evaluation in plastic bonded explosive (PBX) formulations.

There is a need of fine 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) (2-5 microm) for various high explosive formulations to achieve desired mechanical strength, ease in processing and finally, provide better performance of end product. The reprecipitation method for TATB has been developed using concentrated sulfuric acid as a solvent. The reprecipitation parameters of TATB were optimized to achieve required fine TATB of particle size approximately 2-5 microm. The characteristic properties of fine TATB thus obtained have been confirmed by FTIR, DSC and TG-FTIR. The spectroscopic and thermal data obtained for fine TATB were compared with standard coarse TATB and found chemically unchanged during particle size reduction. In the present study, the preparation of fine TATB was also attempted using ultrasonication method. The fine (2-5 microm) TATB has been introduced to study in the bimodal high explosive formulations. High explosive formulations based on coarse (55 microm) and fine TATB ( approximately 2-5 microm) with 10% polyurethane were studied. It was observed that properties like bulk density (1.70 g/cm(3)), mechanical strength/compressed strength (115.9 mg/cm(2)), %elongation (6.36) were improved for fine TATB in comparison with coarse TATB ( approximately 55 microm) alone in high explosive formulations.

Calorimetry, Differential Scanning↗

PubMed2006

Synthesis, characterization and thermolysis of 1,1-diamino-2,2-dinitroethylene (FOX-7) and its salts.

The present paper discusses the efforts made in HEMRL to establish the synthesis of FOX-7 at 100 g/batch level. In the present study, 1,1-diamino-2,2-dinitroethylene has been synthesised by treatment of acetamidinium chloride with diethylmalonate to obtain 2-methyl-pyrimidine-4,6-dione which on nitration followed by hydrolysis gave FOX-7. The synthesised FOX-7 has been characterized by spectroscopic and thermal techniques. The data obtained confirms the structure of FOX-7. The sensitivity of FOX-7 towards mechanical stimuli indicated its insensitive nature. The theoretically computed explosive and ballistic parameters are close to that of RDX. The synthesised FOX-7 has been used as a precursor for the synthesis of potassium and guanidinium salts and the thermal analysis of these salts indicate their exothermic nature.

Ethylenes↗

PubMed2006

Primary explosives: electrostatic discharge initiation, additive effect and its relation to thermal and explosive characteristics.

All explosives, under all conditions must be considered vulnerable to generation, accumulation and discharge of static charge. The low energy static hazards of the order as low as 2-3 mJ need to be guarded against in case of highly sensitive compounds namely primary explosives. The hazard is normally associated with manufacturing and filling operations due to discharge of static charge accumulated on a person supplying energy up to 20 mJ. To reduce the risk associated with static initiation hazard in the processing and handling of the explosives, the electrostatic sensitivity tests can provide an important input regarding electrostatic hazards. This paper presents electrostatic sensitivity data in terms of zero ignition probability data (E(SE0)) of some of the initiatory explosives such as nickel/cobalt hydrazinium nitrate, silver azide, lead azide and mercury salt of 5-nitro tetrazole. Similar data has also been presented for samples coated with polyvinyl pyrrolidone to study its effect on electrostatic sensitivity. The electrostatic spark sensitivity of some conventional and novel made to explain the increased spark sensitivity behavior on the basis of the possible primary explosives has been studied. The electrostatic spark sensitivity of primary explosives decreased in the order of AgN3 = NHN > PbN6 > MNT > CoHN > BNCP. A possible correlation of spark energy with approximation and assumption has been drawn with thermal, detonation and mechanical properties. The polyvinyl pyrrolidone coated samples followed the same order but interestingly with increased spark sensitivity. An attempt has been reasoning of dielectric nature of the materials or exothermic effects of decomposition products of PVP. The present work also reports the electrostatic spark sensitivity of cap compositions.

Explosive Agents↗

PubMed2006

Synthesis, characterization and thermolysis studies on triazole and tetrazole based high nitrogen content high energy materials.

This paper reports the synthesis, characterisation and thermolysis studies of hydrazinium azotetrazolate (HAZ) and 1,1'-dinitro-3,3'-azo-1,2,4-triazole (N-DNAT). TGA and DSC results suggested that HAZ decomposes in the range of 150-180 degrees C and N-DNAT in the range of 160-170 degrees C, respectively. The pattern of decomposition of HAZ dihydrate and N-DNAT has been predicted with the help of pyrolysis GC/MS technique and a probable decomposition mechanism has been proposed. The theoretically predicted performance data suggests the potential nature of HAZ and N-DNAT for their use in propellant/explosive as well as in gas generator formulations.

Hot Temperature↗

PubMed2006

Computer code for the optimization of performance parameters of mixed explosive formulations.

LOTUSES is a novel computer code, which has been developed for the prediction of various thermodynamic properties such as heat of formation, heat of explosion, volume of explosion gaseous products and other related performance parameters. In this paper, we report LOTUSES (Version 1.4) code which has been utilized for the optimization of various high explosives in different combinations to obtain maximum possible velocity of detonation. LOTUSES (Version 1.4) code will vary the composition of mixed explosives automatically in the range of 1-100% and computes the oxygen balance as well as the velocity of detonation for various compositions in preset steps. Further, the code suggests the compositions for which least oxygen balance and the higher velocity of detonation could be achieved. Presently, the code can be applied for two component explosive compositions. The code has been validated with well-known explosives like, TNT, HNS, HNF, TATB, RDX, HMX, AN, DNA, CL-20 and TNAZ in different combinations. The new algorithm incorporated in LOTUSES (Version 1.4) enhances the efficiency and makes it a more powerful tool for the scientists/researches working in the field of high energy materials/hazardous materials.

Algorithms↗

PubMed2006

Diaminofurazan (DAF): Thermolysis and evaluation as ballistic modifier in double base propellant.

Diaminofurazan (DAF) is used as a precursor in the synthesis of many high performance insensitive high explosives. This paper reports the thermal studies on DAF and its evaluation as a ballistic modifier in double base propellant formulations. Differential scanning calorimetry (DSC) and differential thermal analysis (DTA) revealed that DAF shows two-stage decomposition, whereas the kinetics of initial stage of thermal decomposition of DAF evaluated from TG data gave activation energy (E(a)) of 67 kJ mol(-1). The evolution of gases containing species such as CN, NH, OH and oxides of nitrogen during thermal decomposition of DAF was also revealed by hyphenated TG-FTIR data. Evaluation of DAF as a ballistic modifier in RDX incorporated double base propellant formulations indicated that it brings down the pressure index to 0.20 compared to 0.70 for a control composition in the pressure range 6.9-8.8 MPa when used in combination with basic lead salicylate (BLS). It was observed that DAF does not have adverse effect on vulnerability and chemical stability of the propellant formulation.

Calorimetry, Differential Scanning↗

PubMed2005

Quantum chemical, ballistic and explosivity calculations on 2,4,6,8-tetranitro-1,3,5,7-tetraaza cyclooctatetraene: a new high energy molecule.

Ab initio molecular orbital calculations have been carried out on 2,4,6,8-tetranitro-1,3,5,7-tetraazacyclooctatetraene, the tetramer of the series (NO(2)CN)(n) where n=1-4, using the Hartree-Fock theory with the 6-31 G(d) basis set. These calculations yield three conformers for the tetramer with D(4h), C(4h) and C(2) symmetries. The nonplanar conformer with the C(2) symmetry turns out to be 99.0 and 164.4kJmol(-1), respectively, lower in energy than the C(4h) and D(4h) conformers. The electron density topography - the density at the bond critical point - has been used as a measure of the CNO(2) strengths. Based on these bond strengths, heats of formation [obtained from the parametric model 3 (PM3) method] and specific decomposition energies, it may be concluded that (NO(2)CN)(4) is a promising candidate in the class of high energy molecules. Theoretically computed explosive (velocity of detonation, detonation pressure, etc.) and ballistic (characteristic velocity, specific impulse, etc.) parameters support these conclusions.

Electrons↗

PubMed2005

Effect of organic additives on the mitigation of volatility of 1-nitro-3,3'-dinitroazetidine (TNAZ): next generation powerful melt cast able high energy material.

1-Nitro-3,3'-dinitroazetidine (TNAZ) was synthesized based on the lines of reported method. Thermolysis studies on synthesized and characterized TNAZ using differential scanning calorimetry (DSC) and hyphenated TG-FT-IR techniques were undertaken to generate data on decomposition pattern. FT-IR of decomposition products of TNAZ revealed the evolution of oxides of nitrogen and HCN containing species suggesting the cleavage of C/N-NO(2) bond accompanied with the collapse of ring structure. The effect of incorporation of 15% additives namely, 3-amino-1,2,4-triazole (AT), 3,5-diamino-1,2,4-triazole (DAT), carbohydrazide (CHZ), 5,7-dinitrobenzofuroxan (DNBF), bis (2,2-dinitropropyl) succinate (BNPS), triaminoguanidinium nitrate (TAGN), 2,4,6-trinitrobenzoic acid (TNBA) and nitroguanidine (NQ) on the volatility of TNAZ was investigated by undertaking thermogravimetric analysis. The TG pattern brings out the potential of BNPS and TAGN as additives to mitigate the volatility of TNAZ. The influence of additives on thermal decomposition of pattern of TNAZ was also investigated by DSC. The DSC results indicated that the additives did not have appreciable effect on the melting point of TNAZ. Scanning electron microscopic (SEM) studies were carried out to investigate the effect of additives on morphology of TNAZ. This paper also discusses the possible mechanism involved in between the TNAZ and TAGN and BNPS. It appears that the formation of charge transfer complex formation between the TNAZ and TAGN/BNPS. The effect of addition of high explosives such as CL-20, HMX and RDX on thermo-physical characteristics of TNAZ is also reported in this paper.

Azetidines↗

PubMed2005

Prediction of heat of formation and related parameters of high energy materials.

Heat of formation is one of the most important parameters in the performance prediction of explosive and propellant formulations and their individual ingredients. This paper reports the development of user-friendly computer code for the prediction of heat of formation based on two approaches. In first methodology, the logic of Benson's Group additivity method and in the second method, the logic of Pedley method was used for predicting the heats of formation of high energy materials (HEMs). The predicted heats of formation by Benson method for various classes of high energy materials gave deviation in the range of 2-10%, whereas nearly 10-15% deviation was observed using Pedley methodology in comparison to experimental values. The linear regression coefficient values (R(2)) of 0.9947 and 0.9637 are obtained for heat of formation values predicted by this code using methodologies I and II, respectively. The newly developed code LOTUSES (version 1.3) has been validated by calculating the heats of formation of standard explosives such as TNT, pentaerythritol tetranitrate (PETN), RDX, HMX, etc., To the best of our knowledge, no such code is reported in literature which can predict heats of formation values integrated with performance parameters of HEMs belonging to all categories of organic compounds viz. aliphatic, aromatic and heterocyclic materials. The code can also be used to obtain parameters such as velocity of detonation, C-J pressure, volume of explosion products, power index, temperature of explosion and oxygen balance of HEMs. The code has been developed in Visual Basic having enhanced Windows environment. This software namely LOTUSES 1.3 is an updated version of the earlier ones namely LOTUSES 1.1 and 1.2 which do not cater for the calculation of heat of formation and temperature of explosion of HEMs. LOTUSES 1.3 is, therefore, a totally integrated software for computing most of the vital parameters of HEMs requiring mainly the molecular structural information of an explosive under consideration.

Energy-Generating Resources↗

PubMed2005

Studies on diaminoglyoxime (DAG): thermolysis and evaluation as ballistic modifier in double base propellant.

This paper reports thermolysis of diaminoglyoxime (DAG) and its evaluation as a ballistic modifier in double base propellant formulations. Differential scanning calorimetry (DSC) and simultaneous thermal analysis (DTA-thermogravimetric (TG)) revealed that DAG decomposes in two stages. Kinetics of initial stage of thermal decomposition of DAG evaluated from TG data gave activation energy (E(a)) of 153 kJmol(-1). The high-temperature Fourier transform Infrared (FTIR) spectra of DAG suggested preferential cleavage of NO and CNH2 during decomposition. Mass spectral data also suggest possibility of similar process. The hyphenated TG-FTIR data also revealed the evolution of gases containing species, such as CN, NH, OH and oxides of nitrogen during thermal decomposition. Evaluation of DAG as a ballistic modifier in RDX incorporated double base propellant formulations indicated that it brings down the pressure index to 0.17 compared to 0.79 for a control composition in the pressure range 6.9-8.8 MPa when used in combination with basic lead salycilate (BLS). The study suggests that combination of DAG and BLS need to be optimized to achieve more remarkable effects than BLS alone. It was observed that DAG does not have adverse effect on vulnerability and chemical stability of the propellant formulation.

Aerosol Propellants↗

PubMed2005

Establishment of process technology for the manufacture of dinitrogen pentoxide and its utility for the synthesis of most powerful explosive of today--CL-20.

This paper reviews the recent work done on the synthesis as well as characterization of dinitrogen pentoxide (DNPO). The physico-chemical characteristics of DNPO are also discussed. The review brings out the key aspects of N2O5 technology with relevance to realize modern and novel HEMs. The paper also includes the aspects related with establishing the synthesis facility of dinitrogen pentoxide at HEMRL by gas phase interaction of N2O4 with O3. The process parameters for the synthesis of N2O5 at 50 g/batch have been optimized. The synthesized dinitrogen pentoxide has been characterized by UV [204, 213, 258 nm (pi-->pi*) 378 and 384 nm (n-->pi*)] and IR (1428, 1266, 1249, 1206, 1044, 822, 750, 546 and 454 cm(-1)) spectroscopy. The DSC clearly showed the sublimation of N2O5 at 32 degrees C. The nitration studies on 2,6,8,12-tetraacetylhexaaza tetracyclo[5,5,0,0(3,11)0(5,9)]dodecane (TAIW) proved its viability in 2,4,6,8,10,12-hexanitro-2,4,6,8(10,12))-hexaazatetracyclo [5,5,0,0(3,11)0(5,9)]dodecane (CL-20) synthesis. The synthesized CL-20 and its precursors have also been subjected to hyphenated TG-FTIR studies to understand decomposition pattern.

Aza Compounds↗

PubMed2005

Studies on salts of 3-nitro-1,2,4-triazol-5-one (NTO) and 2,4,6-trinitroanilino benzoic acid (TABA): potential energetic ballistic modifiers.

The Co/Cu/Ni/Fe salts of 3-nitro-1,2,4-triazol-5-one (NTO) and 2,4,6-trinitroanilino benzoic acid (TABA) were prepared and characterized during this work. All the salts exhibited exothermic decomposition in DSC. The FT-IR spectra of the gaseous products evolved during TGA of NTO salts indicated the release of NO2 and cleavage of NTO ring during the course of decomposition. Thermal decomposition of TABA salts also produced NO2 on decomposition. The transition metal salts enhanced the burning rates of AP-HTPB composite propellant evaluated during this work. The best catalytic effect was obtained with Fe-NTO salt which increased the burning rate to the extent of approximately 80% as well as brought down the pressure index (n) to 0.18 (2-9MPa).

Aniline Compounds↗

PubMed2005

Energetic co-ordination compounds: synthesis, characterization and thermolysis studies on bis-(5-nitro-2H-tetrazolato-N2)tetraammine cobalt(III) perchlorate (BNCP) and its new transition metal (Ni/Cu/Zn) perchlorate analogues.

Bis-(5-nitro-2H-tetrazolato-N2)tetraammine[cobalt(III)/nickel(III)] perchlorates (BNCP/BNNP) and mono-(5-nitro-H-tetrazolato-N)triammine [copper(II)/zinc(II)] perchlorates (MNCuP/MNZnP) have been synthesized during this work. The synthesis was carried out by addition of carbonato tetraammine metal [Co/Ni/Cu/Zn] nitrate [CTCN/CTNN/CTCuN/CTZnN] to the aqueous solution of sodium salt of 5-nitrotetrazole followed by reaction with perchloric acid. The precursors were synthesized by the reaction of aqueous solution of their respective nitrates with ammonium carbonate at 70 degrees C. The complexes and their precursors were characterized by determining metal and perchlorate content as well as infrared (IR), electron spectra for chemical analysis (ESCA) and X-ray diffraction (XRD) techniques. The TG profiles indicated that BNCP, BNNP and MNCuP are thermally stable up to the temperature of 260-278 degrees C unlike MNZnP (150 degrees C). Sudden exothermic decomposition was observed in case of bis-(5-nitro-2H-tetrazolato-N2)tetraammine cobalt(III) perchlorate, bis-(5-nitro-2H-tetrazolato-N2)tetraammine nickel(III) perchlorate and mono-(5-nitro-H-tetrazolato-N)triammine zinc(II) perchlorate resulting in the severe damage of the sample cup. Sensitivity data indicated that the Co/Ni/Cu complexes are more friction sensitive (3-4.8 kg) than mono-(5-nitro-H-tetrazolato-N)triammine zinc(II) perchlorate (14 kg). The impact sensitivity results of the complexes corresponded to h50% of 30-36 cm.

Cobalt↗

PubMed2005

Synthesis, characterization, thermolysis and performance evaluation studies on alkali metal salts of TABA and NTO.

The lithium (Li) and potassium (K) salts of 3-nitro-1,2,4-triazol-5-one (NTO) and 2,4,6-trinitroanilino benzoic acid (TABA) were prepared and characterized during this work. The synthesis was carried out by addition of a solution of lithium/potassium hydroxide to the aqueous solution of NTO and TABA, respectively. The products were characterized by elemental analysis, metal content determination and Fourier Transform Infrared (FTIR) Spectrum. Differential scanning calorimetry (DSC) profile indicated that Li and K salts of NTO and TABA undergo exothermic decomposition in the temperature range of 257-360 degrees C suggesting their energetic nature. The thermo gravimetric (TG) weight loss pattern revealed loss of water for Li/K salts of NTO and TABA in the temperature range of 115-155 degrees C. Sensitivity results revealed that the compounds are insensitive to impact and friction (impact sensitivity--height of 50% explosion>170 cm and friction insensitivity up to 36 kg) stimuli despite even the parent molecule of NTO salts (NTO) being HEM in the hazard category of 1.1. The FTIR spectra of the gaseous products evolved during TGA of NTO and TABA salts indicated the release of NO2. The formation of products such as LiNCO and KNCO was also observed in case of NTO salts, whereas that of CO2 and NH containing products was indicated in case of TABA salts during this study. In order to assess the performance as energetic ballistic modifiers (EBMs), NTO and TABA salts were incorporated in the ammonium perchlorate-hydroxyl terminated polybutadiene (AP-HTPB) composite propellants. The potassium salts enhanced the burning rate of the propellant. The best catalytic effect was obtained with K-TABA salt, which increased the burning rate to the extent of approximately 81% as well as brought down the n-value to 0.15 (pressure 2-9 MPa).

Aniline Compounds↗

PubMed2005

Spectro-thermal decomposition study of 1,4-dinitroglycoluril (DINGU).

Simultaneous thermal analysis and high temperature FTIR study of 1,4-dinitroglycoluril (DINGU) is reported. TG showed 90% weight loss in the temperature range 225-250 degrees C. Isothermal TG of DINGU showed about 70% weight loss in the temperature range 210-230 degrees C. Kinetic parameters evaluated using a computer program showed that alpha-t data are best described by the Avrami-Erofeev's equation for n=2 with an activation energy of 165 kJ/mol. The kinetics of decomposition of DINGU was followed by studying NH (3388 cm(-1)), CO (1770-1810 cm(-1)) and NO2 symmetric stretching (1565-1570 cm(-1)) IR bands. All three bands showed loss of intensity with temperature and time. alpha-t data of decomposition with respect to NO2 stretching was again best described by the Avrami-Erofeev's equation for n=2. Gaseous decomposition products observed in the IR were N2O, NO2, CO2, HCN and NO. PM3 and Hartree-Fock level calculations on various bond lengths, bond angles and dihedral angles were computed to support the analysis of decomposition study using TG and IR. The data showed that CN and NH bonds are much shorter than the NN bonds, indicative of the weaker NN bond and hence, the possibilities of rupture of the same bond preferentially. This paper also discusses the sensitivity and performance properties of DINGU.

Explosions↗

PubMed2004

Synthesis, characterization and thermal studies on furazan- and tetrazine-based high energy materials.

This paper reports the synthesis of high energy materials (HEMs) viz. 3,3'-diamino-4,4'-azoxyfurazan (DAAF), 3,3s'-azobis(6-amino-1,2,4,5-tetrazine) [DAAT] and 1,4-dihydrazino tetrazine (DHTz). The products obtained were characterized by IR, 1H NMR, 13C NMR and mass spectra. Thermolysis of these compounds carried out by applying TG-DTA and DSC techniques indicated that the thermal stability of DAAF and DAAT was in the temperature range of 230-250 degrees C, whereas that of DHTz was up to approximately 140 degrees C. TG-FTIR of gaseous products of these compounds suggests the evolution of NH2CN/NH3 and HCN as major decomposition products. The impact and friction sensitivity data revealed that DAAF is insensitive to mechanical stimuli whereas DAAT and DHTz are vulnerable to impact stimuli. The cyclic voltammetric studies brought out that, DAAF, DAAT and DHTz are electroactive compounds and thereby can be detected at even low concentration at pH 7 and 13. The theoretical predictions of explosive power of DAAF, DAAT and DHTz alone and their combinations with well-known insensitive high explosives using Becker-Kistiakowsky Wilson (BKW) code as well as that of propellants based on them by NASA-CEC-71 suggest their potential in specific systems.

Explosions↗

PubMed2004

Synthesis, characterization, thermolysis and performance evaluation of mercuric-5-nitrotetrazole (MNT).

Mercuric-5-nitrotetrazole (MNT) was synthesized on using a reported method. The product having bulk density of 1.5 g/cm3, was obtained during this work using mercuric nitrate doped with additives such as cephol/dextrin in the process. Synthesized MNT was characterized by metal content analysis, IR and ESCA. The DTA profile indicated the thermal stability of MNT up to 200 degrees C. It revealed its higher thermally sensitive [thermal sensitive figure (S) approximately 0.8] in comparison to that of service lead azide (SLA) [S approximately 0.4]. Percussion sensitivity data also showed higher sensitivity of MNT. However, it was found less friction sensitive than SLA. The chemical stability of MNT in a carbon dioxide environment was evaluated in comparison to SLA by determining mercury (gravimetrically) and lead azide (volumetrically) contents respectively. Results obtained indicated that no discernable changes occurred in MNT, even after storage for 90 days while in case of SLA, drastic change in lead azide content was observed. IR spectra of MNT sample stored in a closed aluminum dish for 5-10 years could be superimposed on that of the freshly prepared MNT sample. The performance of MNT filled detonator no. 27 assessed in terms of extent of damage on a witness plate was found equivalent to that of the standard ASA (azide, styphynate and aluminium) composition filled detonator.

Explosions↗