PubMed Health⌕ Search

Biomedical subjects

M Sferrazza

Publications and source records attributed to M Sferrazza.

13 recordsLinked to original sources
PubMed2006

Early-stage roughening of the polymer-polymer interface approaching the glass transition temperature by real-time neutron reflection.

The early-stage roughening of the interface between thin deuterated poly(methyl methacrylate) (d-PMMA) layers on thick polystyrene (PS) films was studied as a function of the temperature using real-time specular neutron reflectivity. By measuring the growth of the interface roughness as a precursor of the dewetting, the characteristic time constant of the early stages of the process was studied as a function of the temperature approaching the glass transition temperature (T(g)) of the two polymers from above and compared with the prediction of the growth of the interface by the spinodal process. Both solid and liquid regimes were probed, in which the viscosity of the thin film or the substrate dominates respectively. The characteristic growth time of the process also depends on the upper film thickness to a power of 5 or 6 in the solid or liquid regimes, respectively, as predicted by the theory of spinodal dewetting.

Journal Article↗
PubMed2005

Approaching criticality in polymer-polymer systems.

The interfacial width of polyolefins blends has been probed as a function of distance away from the critical point by using neutron reflectivity. For strongly immiscible polymer pairs, the width of the interface increases slowly when the degree of immiscibility is decreased and the interfacial width varies with the interaction parameter chi of the polymers. Closer to the critical point the dependence on the degree of miscibility becomes stronger and the way in which the interfacial width diverges, as criticality is approached, is related to both the chain length and chi. The self-consistent field theory numerical calculations, with the additional contribution due to capillary waves, provides a good description of the width of the interface between two polymer bulk phases in particular at intermediate values of the degree of immiscibility.

Journal Article↗
PubMed2004

Thickness dependence of structural relaxation in spin-cast, glassy polymer thin films.

The isothermal structural relaxation of glassy, spin-cast polymer thin films has been investigated. Specifically, the thickness h of freshly cast poly(methyl methacrylate) thin films was measured over time using spectroscopic ellipsometry. The spin-cast films exhibit a gradual decrease in thickness, which is attributed to structural relaxation of the glass combined with simultaneous solvent loss. In all cases, h was found to be greater than the equilibrium thickness h(infinity) , which is obtained by cooling slowly from the melt. It is observed that both the rate of the volume relaxation and the fractional departure from h(infinity) (referred to as delta(0) ) increase with increasing film thickness. In the limit of very thin films, the initial h is close to h(infinity) , and delta(0) is small, whereas in thick films (>500 nm) , a plateau value of delta(0) of 0.16 is observed, which is close to the volume fraction of the solvent at the vitrification point. This dependence of delta(0) on thickness is observed regardless of the substrate, polymer molecular weight, or angular velocity during spin casting. Enhanced mobility near film surfaces could be leading to greater relaxation in thinner films prior to, and immediately after, the vitrification of the polymer during the deposition process.

Journal Article↗
PubMed2004

Structural relaxation of spin-cast glassy polymer thin films as a possible factor in dewetting.

Reiter has recently reported a situation in which the dewetting of quasi-solid films is linked to plastic deformation--rather than viscous flow--resulting from capillary forces. Herein we propose that, in thin films of some glassy polymers--especially poly(methyl methacrylate) (PMMA)--prepared by spin-casting from solvent, structural relaxation might impart sufficient stress to cause plastic deformation. We find that PMMA films decrease in thickness by several percent, which is sufficient to create significant stress in those cases in which the film is attached to a rigid substrate. The floating technique, which can take tens of minutes, might allow most of the structural relaxation to occur prior to dewetting experiments.

Journal Article↗
PubMed2003

Influence of the glass transition on solvent loss from spin-cast glassy polymer thin films.

The interdependence of solvent loss and vitrification in spin-cast poly(methyl methacrylate) thin films is explored. Fast measurements of decreases in film thickness, achieved with ellipsometry, indicate that the rate of solvent (toluene) loss decreases sharply when the solvent volume fraction phi(solv) falls below about 0.15 and the film vitrifies. Ellipsometry and microgravimetry show that solvent is lost from a glassy thin film (150 nm thick) over of a period of more than ten hours, which is much longer than would be required if it was limited by diffusion in the glass. These results support the recently-proposed idea that the compression of the glass creates an energy barrier that slows down solvent loss.

Journal Article↗
PubMed2003

Early stages of polymer interdiffusion.

We have examined the wavelength dependence of the diffusion coefficient in a multilayer deuterated polystyrene-hydrogenated polystyrene system. The measurements were performed using neutron reflectivity. The decay of the Bragg peak was also followed in great detail. The measured wavelength diffusion coefficient D(k) was also not found spatially dependent on the distance of the diffusional couples to the substrate. On the basis of our results, it was possible to reconstruct the broadening interface of polymer bilayer sample geometry which had characteristics of a diffuse tail and a sharp core.

Journal Article↗
PubMed2003

Dewetting of thin polymer films at temperatures close to the glass transition.

We present detailed studies on dewetting of thin polystyrene (PS) films which were deposited onto silicon wafers coated with a polydimethylsiloxane (PDMS) monolayer. Experiments were performed at temperatures close to the glass transition temperature of PS. Several significant deviations from the dewetting behaviour of Newtonian liquids were observed. The length of the PS molecules, and thus the viscosity, turned out to be of minor importance in determining the dewetting velocity, in particular for the later regimes. In stark contrast, the geometry of the drying spot had a striking influence on the dewetting velocity. Initially, dewetting from straight contact lines proceeded faster than the opening of circular holes. At later stages, the process slowed down significantly in both cases. Under the conditions at which our experiments were performed, PS cannot flow like a simple liquid. Thus, the observed dewetting has to be the consequence of plastic deformation induced by capillary forces. Our results indicate that under such conditions the energy dissipation process is strongly affected by geometry, which is not the case for viscous liquids.

Journal Article↗
PubMed2002

The timescale of spinodal dewetting at a polymer/polymer interface.

We investigate the dynamics of spinodal dewetting in liquid-liquid polymer systems. Dewetting of poly(methyl-methacrylate) (PMMA) thin films on polystyrene (PS) "substrates" is followed in situ using neutron reflectivity. By following the development of roughness at the PS/PMMA interface and the PMMA surface we extract characteristic growth times for the dewetting process. These characteristic growth times are measured as a function of the molecular weight of the two polymers. By also carrying out experiments in the regime where the dynamics are independent of the PS molecular weight, we are able to use dewetting to probe the scaling of the PMMA thin film viscosity with temperature and molecular weight. We find that this scaling reflects bulk behaviour. However, absolute values are low compared to bulk viscosities, which we suggest may be due in part to slippage at the polymer/polymer interface.

Journal Article↗
PubMed1999

Neutron Reflectivity Study of the Adsorption of beta-Lactoglobulin at a Hydrophilic Solid/Liquid Interface.

Adsorption of a globular protein on a hydrophilic solid/liquid interface was investigated. Neutron reflectivity was used to determine structural information on an adsorbed beta-lactoglobulin layer at a hydrophilic silicon surface. The thickness of the protein film was found to be compatible with the diameter of the native protein, indicating that possible conformational changes of the protein during adsorption are not gross enough to alter the shape of the protein. The amount adsorbed is consistent with that derived by our ellipsometry measurements, obtained in similar experiments. Evidence for significant H-D exchange in the adsorbed protein was found. Copyright 1999 Academic Press.

Journal Article↗