PubMed Health⌕ Search

Biomedical subjects

M Wesseling

Publications and source records attributed to M Wesseling.

5 recordsLinked to original sources
PubMed2001

Influence of plasticization time, curing conditions, storage time, and core properties on the drug release from Aquacoat-coated pellets.

Theophylline or chlorpheniramine maleate pellets were coated with an aqueous ethylcellulose dispersion, Aquacoat. The influence of the plasticization time, curing conditions, storage time, and core properties on the drug release were investigated. The plasticization time (time between plasticizer addition to the polymer dispersion and the spraying process) did not affect the drug release, when the water-soluble plasticizer triethyl citrate, was used because of its rapid uptake by the colloidal polymer particles. In contrast, with the water-insoluble plasticizer acetyltributyl citrate (ATBC), plasticization time (1/2 h vs 24 h) influenced the drug release, the longer plasticization time resulted in a slower drug release because of a more complete plasticizer uptake prior to the coating step. However a thermal aftertreatment of the coated pellets at eleylated temperatures (curing step) reduced/eliminated the effect of the plasticization time with ATBC. In general, curing reduced the drug release and resulted in stable drug release profiles. The time period between the coating and the curing step was not critical when the pellets were cured for a longer time. The structure of the pellet core (high dose matrix vs low dose layered pellet) strongly affected the drug release. A slow, zero-order drug release was obtained with high dose theophylline pellets, while a more rapid, first-order release pattern was obtained with low dose theophylline-layered nonpareil pellets.

Cellulose↗
PubMed1999

Drug release from beads coated with an aqueous colloidal ethylcellulose dispersion, Aquacoat, or an organic ethylcellulose solution.

The objective was to investigate several factors (composition of the coating formulation, the type and pH of the release medium and curing conditions), which influence the drug release from beads coated with either the aqueous ethylcellulose dispersion, Aquacoat or an organic ethylcellulose solution. The chlorpheniramine maleate release from Aquacoat-coated beads was faster in pH 7.4 buffer than in 0.1 N HCl. Increasing the curing time and curing temperature decreased the drug release in pH 7.4 buffer but did not affect the release in 0.1 N HCl. In contrast, the drug release from beads coated with the ethanolic ethylcellulose solution was not affected by the curing step, the release medium or the addition of sodium lauryl sulfate. Scanning electron microscopy and contact angle measurements explained the release data. The differences in the drug release behavior of aqueous--and organic solvent--ethylcellulose--coated beads could be attributed to the differences in the film formation process.

Cellulose↗
PubMed1999

Tackiness of acrylic and cellulosic polymer films used in the coating of solid dosage forms.

The objective was to determine the tackiness of acrylic and cellulosic polymer films in order to make predictions on the tackiness (agglomeration) of coated dosage forms during coating and curing. Force-displacement curves of the detachment process of two polymeric films were used as a measure of tackiness. Various polymers (cellulosic (Aquacoat and acrylics (Eudragit RS 30D, L 30D, NE 30D)), plasticizers (triacetin, triethyl citrate, tributyl citrate, acetyltributyl citrate) and anti-tacking agents (talc and glyceryl monostearate) were investigated. The order of tackiness for films prepared from the different aqueous polymer dispersions was in order of Eudragit NE 30D > RS 30D > RL 30D > Aquacoat. The tackiness increased with increasing plasticizer concentration due to the softening of the polymer. A correlation between the minimum film formation temperature and the tackiness was observed, however, no correlation between the tackiness and the lipophilicity of the plasticizer was seen. Talc and glyceryl monostearate (GMS) reduced the tackiness of the films significantly, with GMS being effective at much lower concentrations. Curing of Eudragit RS 30D-coated theophylline beads at temperatures higher than 40 degrees C in an irreversible agglomeration of the beads and damage of the coating upon separation of the beads. This resulted in a faster release than with uncured beads. Blending the beads with talc just prior to the curing step eliminated the agglomeration and therefore film damage, even at a curing temperature of 60 degrees C.

Acrylates↗
PubMed1993

Multiprocessor and memory architecture of the neurocomputer SYNAPSE-1.

A general purpose neurocomputer, SYNAPSE-1, which exhibits a multiprocessor and memory architecture is presented. It offers wide flexibility with respect to neural algorithms and a speed-up factor of several orders of magnitude--including learning. The computational power is provided by a 2-dimensional systolic array of neural signal processors. Since the weights are stored outside these NSPs, memory size and processing power can be adapted individually to the application needs. A neural algorithms programming language, embedded in C(+2) has been defined for the user to cope with the neurocomputer. In a benchmark test, the prototype of SYNAPSE-1 was 8000 times as fast as a standard workstation.

Algorithms↗