Biomedical subjects

M-K Yeh

Publications and source records attributed to M-K Yeh.

3 recordsLinked to original sources

PubMedDate not supplied

The characteristics of betamethasone-loaded chitosan microparticles by spray-drying method.

Betamethasone (BTM)-loaded microparticles prepared by a spray drying method using chitosan (CTS) as raw material, type-A gelatin and ethylene oxide-propylene oxide block copolymer (Pluronic F68) as modifiers. The BTM-loaded in varied chitosan/Pluronic F68/gelatin microparticle formulations was investigated. By properly choosing excipient type and concentration a high degree of control was achieved over the physical properties of the BTM-loaded microparticles. Microparticle characteristics (zeta potential, tap density, particle size and yield), loading efficiencies, microparticle morphology and in-vitro release properties were examined. Surface morphological characteristics and surface charges of prepared microparticles were observed by using scanning electron microscopy (SEM) and microelectrophoresis. A SEM micrograph shows that the particle sizes of the varied chitosan composed microparticles ranged from 1.1-4.7 microm and the external surfaces appear smooth. The BTM-loaded microparticles entrapped in the chitosan/Pluronic F68/gelatin microparticles with trapping efficiencies up to 93%, collected yield rate 44%, and mean particle size varied between 1-3 microm, positive surface charge (20-40 mv), and tap densities (0.04-0.40 g/cm3) were obtained. The collected BTM yield and size of particle was increased with increasing BTM-loaded amount but both zeta potential and tap density of the particles decreased with increasing BTM-loaded amount. The in vitro release of BTM showed a dose-dependent burst followed by a slower release phase that was proportional to the drug concentration in the concentration range between 5-30%w/w. The in vitro drug release from the chitosan/Pluronic F68/gelatin 1/0.1/0.4 microspheres had a prolong release pattern. These formulation factors were correlated to particulate characteristics for optimizing BTM microspheres in pulmonary delivery.

Anti-Inflammatory Agents↗

PubMedDate not supplied

Japanese encephalitis virus vaccine formulations using PLA lamellar and PLG microparticles.

Japanese encephalitis virus (JEV)-loaded poly(lactide) (PLA) lamellar and poly(DL-lactide-co-glycolide) (PLG) microparticles were successfully prepared with low molecular weight PLA by the precipitate method and with 6% w/v PLG in the organic phase, 10% w/v PVP and 5% w/v NaCl in the continuous phase, by using a water-in-oil-in-water emulsion/solvent extraction technique, respectively. JEV was entrapped in the PLG microparticles by a solvent extraction technique with trapping efficiencies up to 98%, loading level 5.5% w/w, and mean particle size 3.8 microm. The distribution (%) of JEV on the PLG microparticles surface, outer layer, and core were 11.2, 41.7 and 46.4%, respectively. The cumulative release of JEV had an upper limit of approximately 58% of the JEV load at 24 days. The steady release rate was 1.33 microg JEV/mg microparticles/day of JEV release maintained for 24 days. The corresponding virus loading of the PLA lamellae is approximately 0.78% w/w and the loading efficiency (77.8%), JEV content (7.84 microg/mg), and yield (96.3%), respectively. The distribution (%) of JEV on the microparticles surface, outer layer, and core were 82.1, 13.3 and 2.2%, respectively. The live JEV challenge in mice test, in which mice received one dose of 20 mg JEV-loaded PLG microparticles, 20 mg JEV-loaded PLA lamellar in comparison with JEV or PBS solution, was evaluated after IP immunization of BALB/c mice. The study results show that the greatest survival was observed in the group of mice immunized with 20 mg JEV-loaded PLG microparticles and 20 mg JEV-loaded PLA microparticles group (80%). The JEV incorporation, physicochemical characterization data, and the animal results obtained in this study may be relevant in optimizing the vaccine incorporation and delivery properties of these potential vaccine targeting carriers.

Animals↗

PubMedDate not supplied

Optimizing formulation factors in preparing chitosan microparticles by spray-drying method.

The chitosan only, chitosan/Pluronic F68, chitosan/gelatin, chitosan/Pluronic F68/gelatin microparticles and betamethasone-loaded chitosan/Pluronic F68/gelatin microparticles were successfully prepared by a spray-drying method. Microparticle characteristics (yield rate, zeta potential, particle size and tap density), loading efficiencies, microparticle morphology and in-vitro release properties were investigated. By properly choosing excipient type, concentration and varying the spray-drying parameters, a high degree of control was achieved over the physical properties of the dry chitosan powders. SEM micrograph shows that the particle sizes of the varied chitosan composed microparticles ranged from 2.12-5.67 microm and the external surfaces appear smooth. Using betamethasone as model drug, the spray-drying is a promising way to produce good spherical and smooth surface microparticles with a narrow particle size range for controlled delivery of betamethasone. The positively charged betamethasone-loaded microparticles entrapped in the chitosan/Pluronic F68/gelatin microparticles with trapping efficiencies up to 94.5%, yield rate 42.5% and mean particle size 5.64 microm varied between 4.32-6.20 microm and tap densities 0.128 g/cm(3). The pH of particle was increased with increasing betamethasone-loaded amount, but both zeta potential and tap density of the particles decreased with increasing betamethasone-loaded amount. The betamethasone release rates from chitosan/Pluronic F68/gelatin microparticles were influenced by the drug/polymer ratio in the manner that an increase in the release% and burst release% was observed when the drug loading was decreased. The in vitro release of betamethasone showed a dose-dependent burst followed by a slower release phase that was proportional to the drug concentration in the concentration range between 14-44%w/w.

Betamethasone↗