PubMed Health⌕ Search

Biomedical subjects

Mark S Drew

Publications and source records attributed to Mark S Drew.

4 recordsLinked to original sources

Analytic solution for separating spectra into illumination and surface reflectance components.

The measured light spectrum is the result of an illuminant interacting with a surface. The illuminant spectral power distribution multiplies the surface spectral reflectance function to form a color signal--the light spectrum that gives rise to our perception. Disambiguation of the two factors, illuminant and surface, is difficult without prior knowledge. Previously [IEEE Trans. Pattern Anal. Mach. Intell.12, 966 (1990); J. Opt. Soc. Am. A21, 1825 (2004)], one approach to this problem applied a finite-dimensional basis function model to recover the separate illuminant and surface reflectance components that make up the color signal, using principal component bases for lights and for reflectances. We introduce the idea of making use of finite-dimensional models of logarithms of spectra for this problem. Recognizing that multiplications turn into additions in such a formulation, we can replace the original iterative method with a direct, analytic algorithm with no iteration, resulting in a speedup of several orders of magnitude. Moreover, in the new, logarithm-based approach, it is straightforward to further design new basis functions, for both illuminant and reflectance simultaneously, such that the initial basis function coefficients derived from the input color signal are optimally mapped onto separate coefficients that produce spectra that more closely approximate the illuminant and the surface reflectance for any given dimensionality. This is accomplished by using an extra bias correction step that maps the analytically determined basis function coefficients onto the optimal coefficient set, separately for lights and surfaces, for the training set. The analytic equation plus the bias correction is then used for unknown input color signals.

Journal Article↗

On the removal of shadows from images.

This paper is concerned with the derivation of a progression of shadow-free image representations. First, we show that adopting certain assumptions about lights and cameras leads to a 1D, gray-scale image representation which is illuminant invariant at each image pixel. We show that as a consequence, images represented in this form are shadow-free. We then extend this 1D representation to an equivalent 2D, chromaticity representation. We show that in this 2D representation, it is possible to relight all the image pixels in the same way, effectively deriving a 2D image representation which is additionally shadow-free. Finally, we show how to recover a 3D, full color shadow-free image representation by first (with the help of the 2D representation) identifying shadow edges. We then remove shadow edges from the edge-map of the original image by edge in-painting and we propose a method to reintegrate this thresholded edge map, thus deriving the sought-after 3D shadow-free image.

Algorithms↗

Multispectral processing without spectra.

It is often the case that multiplications of whole spectra, component by component, must be carried out,for example when light reflects from or is transmitted through materials. This leads to particularly taxing calculations, especially in spectrally based ray tracing or radiosity in graphics, making a full-spectrum method prohibitively expensive. Nevertheless, using full spectra is attractive because of the many important phenomena that can be modeled only by using all the physics at hand. We apply to the task of spectral multiplication a method previously used in modeling RGB-based light propagation. We show that we can often multiply spectra without carrying out spectral multiplication. In previous work [J. Opt. Soc. Am. A 11, 1553 (1994)] we developed a method called spectral sharpening, which took camera RGBs to a special sharp basis that was designed to render illuminant change simple to model. Specifically, in the new basis, one can effectively model illuminant change by using a diagonal matrix rather than the 3 x 3 linear transform that results from a three-component finite-dimensional model [G. Healey and D. Slater, J. Opt. Soc. Am. A 11, 3003 (1994)]. We apply this idea of sharpening to the set of principal components vectors derived from a representative set of spectra that might reasonably be encountered in a given application. With respect to the sharp spectral basis, we show that spectral multiplications can be modeled as the multiplication of the basis coefficients. These new product coefficients applied to the sharp basis serve to accurately reconstruct the spectral product. Although the method is quite general, we show how to use spectral modeling by taking advantage of metameric surfaces, ones that match under one light but not another, for tasks such as volume rendering. The use of metamers allows a user to pick out or merge different volume structures in real time simply by changing the lighting.

Journal Article↗

A practical approach to spectral volume rendering.

To make a spectral representation of color practicable for volume rendering, a new low-dimensional subspace method is used to act as the carrier of spectral information. With that model, spectral light material interaction can be integrated into existing volume rendering methods at almost no penalty. In addition, slow rendering methods can profit from the new technique of postillumination-generating spectral images in real-time for arbitrary light spectra under a fixed viewpoint. Thus, the capability of spectral rendering to create distinct impressions of a scene under different lighting conditions is established as a method of real-time interaction. Although we use an achromatic opacity in our rendering, we show how spectral rendering permits different data set features to be emphasized or hidden as long as they have not been entirely obscured. The use of postillumination is an order of magnitude faster than changing the transfer function and repeating the projection step. To put the user in control of the spectral visualization, we devise a new widget, a "light-dial," for interactively changing the illumination and include a usability study of this new light space exploration tool. Applied to spectral transfer functions, different lights bring out or hide specific qualities of the data. In conjunction with postillumination, this provides a new means for preparing data for visualization and forms a new degree of freedom for guided exploration of volumetric data sets.

Algorithms↗