Biomedical subjects

Mark W Rutland

Publications and source records attributed to Mark W Rutland.

9 recordsLinked to original sources

PubMed2007

Effect of capillary condensation on friction force and adhesion.

Friction force measurements have been conducted with a colloid probe on mica and silica (both hydrophilic and hydrophobized) after long (24 h) exposure to high-humidity air. Adhesion and friction measurements have also been performed on cellulose substrates. The long exposure to high humidity led to a large hysteresis between loading and unloading in the friction measurements with separation occurring at large negative applied loads. The large hysteresis in the friction-load relationship is attributed to a contact area hysteresis of the capillary condensate which built up during loading and did not evaporate during the unloading regime. The magnitude of the friction force varied dramatically between substrates and was lowest on the mica substrate and highest on the hydrophilic silica substrate, with the hydrophobized silica and cellulose being intermediate. The adhesion due to capillary forces on cellulose was small compared to that on the other substrates, due to the greater roughness of these surfaces.

Adhesiveness↗

PubMed2006

Friction and forces between cellulose model surfaces: a comparison.

Four different cellulose model surfaces, and one silica surface, have been studied by means of atomic force microscopy (AFM). The normal interactions have been found to consist of a longer range double layer force with a short range steric interaction, the nature of which is extensively discussed. Both the surface charge and range of the steric force depend on the type of cellulose substrate used, as does the magnitude of the adhesion. Studies of friction reveal that surface roughness is the determining factor for the friction coefficient, with which it increases monotonically. The absolute value, however, is determined by the surface chemistry. All studied cellulose surfaces show similar behavior in response to xyloglucan addition.

Cellulose↗

PubMed2006

Friction between cellulose surfaces and effect of xyloglucan adsorption.

The forces and friction between cellulose spheres have been measured in the absence and presence of xyloglucan using an atomic force microscope. The forces between cellulose are monotonically repulsive with negligible adhesion after contact is achieved. The friction coefficient is observed to be unusually high in comparison with other nanotribological systems. We have confirmed that xyloglucan adsorbs strongly to cellulose, which results in a much stronger adhesion, which is dependent on the time the surfaces are in contact. Xyloglucan also increases the repulsion on approach of the cellulose surfaces, and the friction is markedly reduced. The apparently incompatible observations of decreased friction in combination with increased adhesion fulfills many of the necessary criteria for a papermaking additive.

Adsorption↗

PubMed2005

Hydration state of nonionic surfactant monolayers at the liquid/vapor interface: structure determination by vibrational sum frequency spectroscopy.

The OH stretching region of water molecules in the vicinity of nonionic surfactant monolayers has been investigated using vibrational sum frequency spectroscopy (VSFS) under the polarization combinations ssp, ppp, and sps. The surface sensitivity of the VSFS technique has allowed targeting the few water molecules present at the surface with a net orientation and, in particular, the hydration shell around alcohol, sugar, and poly(ethylene oxide) headgroups. Dramatic differences in the hydration shell of the uncharged headgroups were observed, both in comparison to each another and in comparison to the pure water surface. The water molecules around the rigid glucoside and maltoside sugar rings were found to form strong hydrogen bonds, similar to those observed in tetrahedrally coordinated water in ice. In the case of the poly(ethylene oxide) surfactant monolayer a significant ordering of both strongly and weakly hydrogen bonded water was observed. Moreover, a band common to all the surfactants studied, clearly detected at relatively high frequencies in the polarization combinations ppp and sps, was assigned to water species located in proximity to the surfactant hydrocarbon tail phase, with both hydrogen atoms free from hydrogen bonds. An orientational analysis provided additional information on the water species responsible for this band.

Alcohols↗

PubMed2005

Friction force measurements relevant to de-inking by means of atomic force microscope.

In the pulping step of the de-inking process, the ink detaches from the fibers due to shear and physical chemical interaction. In order to get a better understanding of the forces involved between cellulose and ink, the atomic force microscope and the colloidal probe technique have been used in the presence of a model chemical dispersant (hexa-ethyleneglycol mono n-dodecyl ether, C12E6). A cellulose bead was used as the colloidal probe and three different lower surfaces have been used, an alkyd resin, mica and a cellulose sphere. The normal and lateral forces have been measured at a range of nonionic concentrations. It was found that the lateral sliding friction forces deceased with increasing surfactant concentration for both the alkyd resin and mica while no differences were observed for the cellulose surface. In addition, only a very small change in normal force could be detected for the alkyd surface as the concentration changed.

Journal Article↗

PubMed2005

Forces between silica surfaces with adsorbed cationic surfactants: influence of salt and added nonionic surfactants.

Forces have been measured between silica surfaces with adsorbed surfactants by means of a bimorph surface force apparatus. The surfactants used are the cationic surfactant tetradecyltrimethylammonium bromide (TTAB) and the nonionic surfactant hexakis(ethylene glycol) mono-n-tetradecyl ether (C(14)E(6)) as well as mixtures of these two surfactants. The measurements were made at elevated pH, and the effect of salt was studied. At high pH the glass surface is highly charged, which increases the adsorption of TTAB. Despite the low adsorption generally seen for nonionic surfactants on silica at high pH, addition of C(14)E(6) has a considerable effect on the surface forces between two glass surfaces in a TTAB solution. The barrier force is hardly affected, but the adhesion is reduced remarkably. Also, addition of salt decreases the adhesion, but increases the barrier force. In the presence of salt, addition of C(14)E(6) also increases the thickness of the adsorbed layer. The force barrier height is also shown to be related to literature values for surface pressure data in these systems.

Journal Article↗

PubMed2005

A vibrational sum frequency spectroscopy study of the liquid-gas interface of acetic acid-water mixtures: 2. Orientation analysis.

Vibrational sum frequency spectroscopy has been used to investigate the surface of aqueous acetic acid solutions. By studying the methyl and carbonyl vibrations with different polarization combinations, an orientation analysis of the acetic acid molecules has been performed in the concentration range 0-100%. The surface tension of acetic acid solutions was also measured in order to obtain the surface concentration. The orientation of the interfacial acetic acid molecules was found to remain essentially constant in an upright position with the methyl group directed toward the gas phase in the whole concentration range. The tilt angle (theta(CH)3) of the symmetry axis of the methyl group with respect to the surface normal was found to be lower than 15 degrees when considering a delta distribution of angles or as narrow as 0 +/- 11 degrees when assuming a Gaussian distribution. Further investigations showed that the C=O bond tilt (theta(C)(=)(O)) of the acetic acid hydrated monomer was constant and close to 55 degrees in the concentration range where it was detected. Finally, the orientation information is discussed in terms of different species of acetic acid, where the formation of a surface layer of acetic acid cyclic dimers is proposed at high acid concentrations.

Journal Article↗

PubMed2005

A vibrational sum frequency spectroscopy study of the liquid-gas interface of acetic acid-water mixtures: 1. Surface speciation.

Aqueous acetic acid solutions have been studied by vibrational sum frequency spectroscopy (VSFS) in order to acquire molecular information about the liquid-gas interface. The concentration range 0-100% acetic acid has been studied in the CH/OH and the C-O/C=O regions, and in order to clarify peak assignments, experiments with deuterated acetic acid and water have also been performed. Throughout the whole concentration range, the acetic acid is proven to be protonated. It is explicitly shown that the structure of a water surface becomes disrupted even at small additions of acetic acid. Furthermore, the spectral evolution upon increasing the concentration of acetic acid is explained in terms of the different complexes of acetic acid molecules, such as the hydrated monomer, linear dimer, and cyclic dimer. In the C=O region, the hydrated monomer is concluded to give rise to the sum frequency (SF) signal, and in the CH region, the cyclic dimer contributes to the signal as well. The combination of results from the CH/OH and the C-O/C=O regions allows a thorough characterization of the behavior of the acetic acid molecules at the interface to be obtained.

Journal Article↗

PubMed2003

Lubricating properties of the initial salivary pellicle--an AFM study.

The role of saliva in the oral cavity is manifold; an important function is to serve as lubricant between hard (enamel) and soft (mucosal) tissues. Intraoral lubrication is of crucial importance in order to maintain functions such as deglutition, mastication and the faculty of speech. A large number of people suffer from impaired salivary functions, displaying symptoms such as 'dry mouth'. This results in a need for methods to assess the lubricating properties of both native saliva and potential artificial saliva formulations. Here, normal as well as lateral forces, acting between adsorbed salivary films, have been measured for the first time by means of colloidal probe atomic force microscopy (AFM). It was found that the presence of salivary pellicles between hard surfaces reduces the friction coefficient by a factor of 20. This reduction of friction is consistent with the long-range purely repulsive nature of the normal forces acting between the salivary films. The lubricating mechanism is presumably based on a full separation of the sliding surfaces by the salivary films. The friction between salivary films has been investigated at normal loads that cover the clinical jaw closing forces, and it can be concluded that the lubricating properties are maintained within this load interval. The present study indicates the usefulness of colloidal probe AFM, which offers a direct and quantitative measure of lubrication at a molecular level, in the study of biotribological phenomena. In particular, the results obtained here may have implications for the development of saliva substitutes.

Adult↗