PubMed Health⌕ Search

Biomedical subjects

Michael Grätzel

Publications and source records attributed to Michael Grätzel.

At least 19 recordsLinked to original sources
PubMed2006

Molecular engineering of organic sensitizers for solar cell applications.

Novel organic sensitizers comprising donor, electron-conducting, and anchoring groups were engineered at molecular level and synthesized. The functionalized unsymmetrical organic sensitizers 3-{5-[N,N-bis(9,9-dimethylfluorene-2-yl)phenyl]-thiophene-2-yl}-2-cyano-acrylic acid (JK-1) and 3-{5'-[N,N-bis(9,9-dimethylfluorene-2-yl)phenyl]-2,2'-bisthiophene-5-yl}-2-cyano-acrylic acid (JK-2), upon anchoring onto TiO2 film, exhibit unprecedented incident photon to current conversion efficiency of 91%. The photovoltaic data using an electrolyte having composition of 0.6 M M-methyl-N-butyl imidiazolium iodide, 0.04 M iodine, 0.025 M LiI, 0.05 M guanidinium thiocyanate, and 0.28 M tert-butylpyridine in a 15/85 (v/v) mixture of valeronitrile and acetonitrile revealed a short circuit photocurrent density of 14.0 +/- 0.2 mA/cm2, an open circuit voltage of 753 +/- 10 mV, and a fill factor of 0.76 +/- 0.02, corresponding to an overall conversion efficiency of 8.01% under standard AM 1.5 sunlight. DFT/TDDFT calculations have been performed on the two organic sensitizers to gain insight into their structural, electronic, and optical properties. Our results show that the cyanoacrylic acid groups are essentially coplanar with respect to the thiophene units, reflecting the strong conjugation across the thiophene-cyanoacrylic groups. Molecular orbitals analysis confirmed the experimental assignment of redox potentials, while TDDFT calculations allowed assignment of the visible absorption bands.

Journal Article↗
PubMed2006

A supercooled imidazolium iodide ionic liquid as a low-viscosity electrolyte for dye-sensitized solar cells.

A series of allyl-functionalized imidazolium salts are reported, including 1-allyl-3-ethylimidazolium iodide and 1-allyl-3-propylimidazolium iodide, which have melting points close to room temperature and show typical properties of supercooled fluids if heated above their melting points. Their viscosities in the liquid state are considerably lower than the benchmark ionic liquid used in solar cells, viz., 1-propyl-3-methylimidazolium iodide. Electrolytes containing these new liquids provide excellent efficiencies and good stability in dye-sensitized solar cells when subjected to an accelerated-light soaking test at 60 degrees C. The structures of three of the new salts have been established in the solid state by single-crystal X-ray analysis.

Journal Article↗
PubMed2006

Characteristics of high efficiency dye-sensitized solar cells.

Impedance spectroscopy was applied to investigate the characteristics of dye-sensitized nanostructured TiO2 solar cells (DSC) with high efficiencies of light to electricity conversion of 11.1% and 10.2%. The different parameters, that is, chemical capacitance, steady-state transport resistance, transient diffusion coefficient, and charge-transfer (recombination) resistance, have been interpreted in a unified and consistent framework, in which an exponential distribution of the localized states in the TiO2 band gap plays a central role. The temperature variation of the chemical diffusion coefficient dependence on the Fermi-level position has been observed consistently with the standard multiple trapping model of electron transport in disordered semiconductors. A Tafel dependence of the recombination resistance dependence on bias potential has been rationalized in terms of the charge transfer from a distribution of surface states using the Marcus model of electron transfer. The current-potential curve of the solar cells has been independently constructed from the impedance parameters, allowing a separate analysis of the contribution of different resistive processes to the overall conversion efficiency.

Journal Article↗
PubMed2006

Alkyl chain barriers for kinetic optimization in dye-sensitized solar cells.

The optimization of interfacial charge transfer is crucial to the design of dye-sensitized solar cells. In this paper we address the dynamics of the charge separation and recombination in liquid-electrolyte and solid-state cells employing a series of amphiphilic ruthenium dyes with varying hydrocarbon chain lengths, acting as an insulating barrier for electron-hole recombination. Dynamics of electron injection, monitored by time-resolved emission spectroscopy, and of charge recombination and regeneration, monitored by transient optical absorption spectroscopy, are correlated with device performance. We find that increasing dye alkyl chain length results in slower charge recombination dynamics to both the dye cation and the redox electrolyte or solid-state hole conductor (spiro-OMeTAD). These slower recombination dynamics are however paralleled by reduced rates for both electron injection into the TiO2 electrode and dye regeneration by the I-/I3- redox couple or spiro-OMeTAD. Kinetic competition between electron recombination with dye cations and dye ground state regeneration by the iodide electrolyte is found to be a key factor for liquid electrolyte cells, with optimum device performance being obtained when the dye regeneration is just fast enough to compete with electron-hole recombination. These results are discussed in terms of the minimization of kinetic redundancy in solid-state and liquid-electrolyte dye-sensitized photovoltaic devices.

Journal Article↗
PubMed2006

Pyrene fluorescence at air/sodium dodecyl sulfate solution interface.

The dependence of pyrene fluorescence spectra on the concentration of sodium dodecyl sulfate (SDS) was observed, where the solution was prepared from water saturated with pyrene. The values of the I(1)/I(3) ratio from the bulk solution and from the upper meniscus region in an optical cell were similar but decreased rapidly around the critical micelle concentration (cmc) of SDS, indicating that pyrene molecules preferred to be solubilized in the micelles having a lower dielectric constant. The fluorescence intensity of the excimer indicated the concentration of pyrene molecules at the air/solution interface or the surface activity of pyrene molecules. In addition, the intensity from the meniscus region is much larger than that from the bulk at the concentrations below the cmc, whereas there was no difference in the intensity between the bulk and the meniscus above 8 mmol dm(-3) of SDS. The analysis of the fluorescence intensity from the excimer strongly suggests the presence of molecular aggregates that are favorable to the pyrene molecules just like the micelles in the bulk, making them less movable.

Air↗
PubMed2006

New benchmark for water photooxidation by nanostructured alpha-Fe2O3 films.

Thin films of silicon-doped Fe2O3 were deposited by APCVD (atmospheric pressure chemical vapor deposition) from Fe(CO)5 and TEOS (tetraethoxysilane) on SnO2-coated glass at 415 degrees C. HRSEM reveals a highly developed dendritic nanostructure of 500 nm thickness having a feature size of only 10-20 nm at the surface. Real surface area determination by dye adsorption yields a roughness factor of 21. XRD shows the films to be pure hematite with strong preferential orientation of the [110] axis vertical to the substrate, induced by silicon doping. Under illumination in 1 M NaOH, water is oxidized at the Fe2O3 electrode with higher efficiency (IPCE = 42% at 370 nm and 2.2 mA/cm2 in AM 1.5 G sunlight of 1000 W/m2 at 1.23 VRHE) than at the best reported single crystalline Fe2O3 electrodes. This unprecedented efficiency is in part attributed to the dendritic nanostructure which minimizes the distance photogenerated holes have to diffuse to reach the Fe2O3/electrolyte interface while still allowing efficient light absorption. Part of the gain in efficiency is obtained by depositing a thin insulating SiO2 interfacial layer between the SnO2 substrate and the Fe2O3 film and a catalytic cobalt monolayer on the Fe2O3 surface. A mechanistic model for water photooxidation is presented, involving stepwise accumulation of four holes by two vicinal iron or cobalt surface sites.

Adsorption↗
PubMed2006

Stable single-layer light-emitting electrochemical cell using 4,7-diphenyl-1,10-phenanthroline-bis(2-phenylpyridine)iridium(III) hexafluorophosphate.

A significant improvement in the stability of a light emitting electrochemical cell was achieved by utilizing a novel iridium(III) complex: 4,7-diphenyl-1,10-phenanthroline-bis(2-phenylpyridine)iridium(III) hexafluorophosphate. The enhanced device stability is correlated by means of DFT studies to be related to a more efficient shielding of the reactive LUMO of the complex.

Journal Article↗
PubMed2006

Three-channel transmission line impedance model for mesoscopic oxide electrodes functionalized with a conductive coating.

A three-channel transmission line (TL) impedance model is proposed to address the charge transport behavior of molecular functionalized mesoscopic oxide electrodes at different bias conditions. A full general solution of the three-channel TL for the system is provided in this paper. Selected experimental results of impedance spectroscopy of mesoscopic Al2O3 and TiO2 networks, covered with a monolayer of Ru complex cis-RuLL'(NCS)2 (L = 2,2'-bipyridyl-4,4'-dicarboxylic acid, L' = 4,4'-dinonyl-2,2'-bipyridyl) (Z907), are briefly discussed. It shows that the model constitutes a useful tool for characterizing nanoporous electrodes functionalized with organic conducting layers in the surface. The model makes it possible to determine the separate conductivity of substrate oxide and molecular layer, and interfacial charge transfer, in the functionalized nanostructured electrodes.

Journal Article↗
PubMed2006

Translucent thin film Fe2O3 photoanodes for efficient water splitting by sunlight: nanostructure-directing effect of Si-doping.

Thin, silicon-doped nanocrystalline alpha-Fe2O3 films have been deposited on F-doped SnO2 substrates by ultrasonic spray pyrolysis and chemical vapor deposition at atmospheric pressure. The photocatalytic activity of these films with regard to photoelectrochemical water oxidation was measured at pH 13.6 under simulated AM 1.5 global sunlight. The photoanodes prepared by USP and APCVD gave 1.17 and 1.45 mA/cm2, respectively, at 1.23 V vs RHE. The morphology of the alpha-Fe2O3 was strongly influenced by the silicon doping, decreasing the feature size of the mesoscopic film. The silicon-doped alpha-Fe2O3 nano-leaflets show a preferred orientation with the (001) basal plane normal to the substrate. The best performing photoanode would yield a solar-to-chemical conversion efficiency of 2.1% in a tandem device using two dye-sensitized solar cells in series.

Journal Article↗
PubMed2006

Molecular wiring of nanocrystals: NCS-enhanced cross-surface charge transfer in self-assembled Ru-complex monolayer on mesoscopic oxide films.

We report on rapid ambipolar cross-surface charge transfer within self-assembled monolayers (SAM) of the heteroleptic Ru-complexes cis-RuLL'(NCS)(2) (L = 2,2'-bipyridyl-4,4'-dicarboxylic acid, L' = 4,4'-dinonyl-2,2'-bipyridyl) (1) and cis-RuLL' '(NCS)(2) (L = 2,2'-bipyridyl-4,4'-dicarboxylic acid, L' = 4,4'-dimethyl-2,2'-bipyridyl) (2) on the surface of mesoscopic insulating oxide films. The bipyridyl ligands of the Ru-complex transport electrons, while the NCS groups plays a pivotal role in mediating surface confined hole percolation. Molecular dynamics calculations show the NCS ligands of 1 and 2 to orient in a fashion that enhances the overlap of the HOMOs of neighboring ruthenium complexes. Using ab initio Hartree-Fock calculations the electronic coupling matrix element for intermolecular hole exchange at the surface is estimated to be 0.13 eV. Cyclic voltammetry as well as spectroelectrochemical and impedance measurements performed with a series of other Ru-complexes confirmed the control of the cross surface charge transfer by the molecular structure. Complex 2 shows the highest percolation rate, the surface hole diffusion coefficient being 1.1 x 10(-8) cm(2)/s. The effects of the ligand properties, such as denticity, geometry, and size, on the intermolecular charge transport are discussed in detail.

Journal Article↗
PubMed2006

High molar extinction coefficient heteroleptic ruthenium complexes for thin film dye-sensitized solar cells.

Two novel heteroleptic sensitizers, Ru((4,4-dicarboxylic acid-2,2'-bipyridine)(4,4'-bis(p-hexyloxystyryl)-2,2-bipyridine)(NCS)2 and Ru((4,4-dicarboxylic acid-2,2'-bipyridine)(4,4'-bis(p-methoxystyryl)-2,2'-bipyridine) (NCS)2, coded as K-19 and K-73, respectively, have been synthesized and characterized by 1H NMR, FTIR, UV-vis absorption, and emission spectroscopy and excited-state lifetime and spectroelectrochemical measurements. The introduction of the alkoxystyryl group extends the conjugation of the bipyridine donor ligand increasing markedly their molar extinction coefficient and solar light harvesting capacity. The dynamics of photoinduced charge separation following electronic excitation of the K-19 dye was scrutinized by time-resolved laser spectroscopy. The electron transfer from K-19 to the conduction band of TiO2 is completed within 20 fs while charge recombination has a half-life time of 800 s. The high extinction coefficients of these sensitizers enable realization of a new generation of a thin film dye sensitized solar cell (DSC) yielding high conversion efficiency at full sunlight even with viscous electrolytes based on ionic liquids or nonvolatile solvents. An unprecedented yield of over 9% was obtained under standard reporting conditions (simulated global air mass 1.5 sunlight at 1000 W/m2 intensity) when the K-73 sensitizer was combined with a nonvolatile "robust" electrolyte. The K-19 dye gave a conversion yield of 7.1% when used in conjunction with the binary ionic liquid electrolyte. These devices exhibit excellent stability under light soaking at 60 degrees C. The effect of the mesoscopic TiO2 film thickness on photovoltaic performance has been analyzed by electrochemical impedance spectroscopy (EIS).

Journal Article↗
PubMed2006

Influence of ionic liquids bearing functional groups in dye-sensitized solar cells.

Ionic liquids containing the nitrile and vinyl functional groups attached to imidazolium cations combined with various anions, e.g., iodide, bis[(trifluoromethyl)sulfonyl]imide ([TFSI]-), or dicyanamide ([N(CN)2]-), have been prepared and characterized. These ionic liquids have been successfully used as electrolytes for dye-sensitized solar cells based on nanocrystalline TiO2 with the amphiphilic ruthenium sensitizer [ruthenium (4,4'-dicarboxylic acid-2,2'-bipyridine)(4,4'-bis(p-hexyloxystyryl)-2,2'-bipyridine)][NCS]2 (coded K-19). The iodide salt was used in 3-methoxypropionitrile-based electrolytes, and the performances of both types of devices were evaluated on the basis of their photocurrent density-voltage characteristics and dark current measurements, demonstrating that the functional groups do not exert a detrimental effect on the performance. The solid-state structure of the nitrile-functionalized salt [C1C3CN(im)]I has also been established by single-crystal X-ray diffraction, revealing extensive hydrogen bonding between the cation protons and the iodide.

Journal Article↗
PubMed2006

DFT-INDO/S modeling of new high molar extinction coefficient charge-transfer sensitizers for solar cell applications.

A new ruthenium(II) complex, tetrabutylammonium [ruthenium (4-carboxylic acid-4'-carboxylate-2,2'-bipyridine)(4,4'-di(2-(3,6-dimethoxyphenyl)ethenyl)-2,2'-bipyridine)(NCS)(2)] (N945H), was synthesized and characterized by analytical, spectroscopic, and electrochemical techniques. The absorption spectrum of the N945H sensitizer is dominated by metal-to-ligand charge-transfer (MLCT) transitions in the visible region, with the lowest allowed MLCT bands appearing at 25 380 and 18 180 cm(-1). The molar extinction coefficients of these bands are 34 500 and 18 900 M(-1) cm(-1), respectively, and are significantly higher when compared to than those of the standard sensitizer cis-dithiocyanatobis(4,4'-dicarboxylic acid-2,2'-bipyridine)ruthenium(II). An INDO/S and density functional theory study of the electronic and optical properties of N945H and of N945 adsorbed on TiO(2) was performed. The calculations point out that the top three frontier-filled orbitals have essentially ruthenium 4d (t(2g) in the octahedral group) character with sizable contribution coming from the NCS ligand orbitals. Most critically the calculations reveal that, in the TiO(2)-bound N945 sensitizer, excitation directs charge into the carboxylbipyridine ligand bound to the TiO(2) surface. The photovoltaic data of the N945 sensitizer using an electrolyte containing 0.60 M butylmethylimidazolium iodide, 0.03 M I(2), 0.10 M guanidinium thiocyanate, and 0.50 M tert-butylpyridine in a mixture of acetonitrile and valeronitrile (volume ratio = 85:15) exhibited a short-circuit photocurrent density of 16.50 +/- 0.2 mA cm(-2), an open-circuit voltage of 790 +/- 30 mV, and a fill factor of 0.72 +/- 0.03, corresponding to an overall conversion efficiency of 9.6% under standard AM (air mass) 1.5 sunlight, and demonstrated a stable performance under light and heat soaking at 80 degrees C.

Journal Article↗
PubMed2006

Efficient and stable solid-state light-emitting electrochemical cell using tris(4,7-diphenyl-1,10-phenanthroline)ruthenium(II) hexafluorophosphate.

The complex tris(4,7-diphenyl-1,10-phenanthroline)ruthenium(II), prepared via a simple microwave-assisted synthesis, was used to prepare a single-layer light-emitting electrochemical cell. This device reaches a high power efficiency of 1.9 Lum/W at a brightness of 390 cd/m2. Moreover, its lifetime is an order of magnitude longer than that of a similar cell making use of tris(bipyridine)ruthenium(II) as the emitting complex.

Journal Article↗