PubMed Health⌕ Search

Biomedical subjects

N Wen

Publications and source records attributed to N Wen.

5 recordsLinked to original sources

Three types of defense-responsive genes are involved in resistance to bacterial blight and fungal blast diseases in rice.

Bacterial blight and fungal blast diseases of rice, caused by Xanthomonas oryzae pv. oryzae and Pyricularia grisea Sacc., respectively, are two of the most devastating diseases in rice worldwide. To study the defense responses to infection with each of these pathogens, expression profiling of 12 defense-responsive genes was performed using near-isogenic rice lines that are resistant or susceptible to bacterial blight and fungal blast, respectively, and rice cultivars that are resistant or susceptible to both pathogens. All 12 genes showed constitutive expression, but expression levels increased in response to infection. Based on their expression patterns in 12 host-pathogen combinations, these genes could be classified into three types, pathogen non-specific (6), pathogen specific but race non-specific (4) and race specific (2). Most of the 12 genes were only responsive during incompatible interactions. These results suggest that bacterial blight and fungal blast resistances share common pathway(s), but are also regulated by different defense pathways in rice. Activation of the corresponding R gene is the key step that initiates the action of these genes in defense responses. The chromosomal locations and pathogen specificities of seven of the 12 genes were consistent with those of previously identified quantitative trait loci for rice disease resistance, which indicates that some of the 12 genes studied may have a phenotypic impact on disease resistance in rice.

Bacteria↗

[The influential factors on DNA cycle sequencing and data evaluation of practical example].

OBJECTIVE: To study some factors that may influence DNA sequencing by analyzing 2040 sequencing samples retrospectively. METHODS: The effects of DNA templates, primers, cycle sequencing reactions as well as purification methods were comparatively analyzed. RESULTS: 70 percent of sequencing failure is caused by DNA template. Characteristics of data from poor template preparation include top-heavy with a short read length, acceptable signal with some noise peaks (Ns), weak signal, overall noise and flat lines or no signal. The ineffective primers can cause 15.4 percent sequencing failure. Possible explanations include primer mismatches and low Tm value. CONCLUSIONS: The quality of template DNA can have a major impact on the quality of the DNA sequencing. Purification of the extension products is absolutely necessary in DNA sequencing, and isopropanol precipitation is highly recommended for this procedure.

Animals↗

Fusion of low-fusing porcelain to Ti-75 alloy: an experimental study.

OBJECTIVE: To study the stomatological feasibility of low-fusing porcelain fused to Ti-75 alloy. METHODS: Electroprobemicroanalysis (EPMA) and shear test were used to observe interface state and bonding strength of porcelaintitanium. RESULTS: Shear bond strengths of low-fusing porcelain with Ti-75 alloy and conventional porcelain each fused to metal (NC-VMK68) were 47.38 +/- 7.95 MPa and 48.50 +/- 7.60 MPa, respectively. There was no significant difference between the shear bonding strength of low-fusing porcelain with Ti-75 and that of conventional porcelain fused to metal (PFM) (P > 0.05). EPMA showed that Ti-75 alloy and low-fusing porcelain bound tightly, had no fissure, and that low-fusing porcelain had good infiltration to Ti-75. It was shown that Ti spread from Ti-75 basal body into porcelain, and elements such as Si-Sn spread from porcelain to Ti-75. CONCLUSION: Ti-75 alloy can be used stomatologically, as a porcelain alloy.

Biocompatible Materials↗

[Study of low-fusing porcelain fused to Ti-75 alloy].

OBJECTIVE: To study the feasibility of low-fusing porcelain fused to Ti-75 alloy. METHODS: The bond strength and interfacial state of porcelain-titanium were observed by EPM analysis and shear test. RESULTS: The results showed that the shear bond strength of low-fusing porcelain fused with Ti-75 alloy and the conventional porcelain fused to base metal alloy (NC-VMK68) respectively were 47.38 +/- 7.95 MPa and 48.50 +/- 7.60 MPa. There were no significant difference in the shear bond strength between the two results (P > 0.05). The analysis of electron microprobe showed that there was no crack in the interface, the low-fusing porcelain permeated Ti-75 alloy fairly, and titanium diffused from Ti-75 alloy to porcelain, and silicon, stannum diffused from porcelain to Ti-75 alloy. CONCLUSION: Ti-75 alloy can be regarded as a suitable alloy for low-fusing porcelain.

Dental Alloys↗

Atherosclerosis of the carotid artery: evaluation by magnetic resonance angiography.

Carotid artery atherosclerotic plaques (APs) can lead to brain ischemia, an event shown to correlate with both the degree of stenosis and the composition of the AP. Currently, accurate estimates of stenosis can be obtained by either x-ray angiography or three-dimensional time-of-flight (TOF) magnetic resonance angiography (MRA). Our purpose was to determine whether three-dimensional TOF MRA images could also provide information on plaque location, morphology, and composition. Seven pre-endarterectomy patients underwent three-dimensional TOF MRA. After endarterectomy, plaque histology was evaluated. Three-dimensional TOF MRA images contained sufficient soft tissue contrast to differentiate the plaques from the surrounding tissues in all cases. Estimation of plaque morphology had 80% correlation with histology. Finally, intraplaque hemorrhage and calcification were deplicted as regions of moderately high and very low intensity, respectively. These preliminary results suggest that three-dimensional TOF MRA may be useful in studying the development and progression of carotid atherosclerosis.

Aged↗