Biomedical subjects

O H Willemsen

Publications and source records attributed to O H Willemsen.

4 recordsLinked to original sources

PubMed2000

Biomolecular interactions measured by atomic force microscopy.

Atomic force microscopy (AFM) is nowadays frequently applied to determine interaction forces between biological molecules. Starting with the detection of the first discrete unbinding forces between ligands and receptors by AFM only several years ago, measurements have become more and more quantitative. At the same time, theories have been developed to describe and understand the dynamics of the unbinding process and experimental techniques have been refined to verify this theory. In addition, the detection of molecular recognition forces has been exploited to map and image the location of binding sites. In this review we discuss the important contributions that have led to the development of this field. In addition, we emphasize the potential of chemically well-defined surface modification techniques to further improve reproducible measurements by AFM. This increased reproducibility will pave the way for a better understanding of molecular interactions in cell biology.

Biophysics↗

PubMed1999

A physical approach to reduce nonspecific adhesion in molecular recognition atomic force microscopy.

Atomic force microscopy is one of the few techniques that allow analysis of biological recognition processes at the single-molecule level. A major limitation of this approach is the nonspecific interaction between the force sensor and substrate. We have modeled the nonspecific interaction by looking at the interaction potential between a conical Si3N4 tip with a spherical end face and a mica surface in solution, using DLVO (Derjaguin, Landau, Verwey, Overbeek) theory and numerical calculations. Insertion of the tip-sample potential in a simulation of an approach-retract cycle of the cantilever gives the well-known force-distance curve. Simulating a force-distance curve at low salt concentration predicts a discrete hopping of the tip, caused by thermal fluctuations. This hopping behavior was observed experimentally and gave rise to a novel approach to making measurements in adhesion mode that essentially works in the repulsive regime. The distance between tip and sample will still be small enough to allow spacer-involved specific interactions, and the percentage of nonspecific interactions of the bare tip with the mica is minimized. We have validated this physical model by imaging intercellular adhesion molecule 1 (ICAM-1) antigen with a tip functionalized with anti-ICAM-1 antibody. The measurement demonstrated that a significant decrease in the number of nonspecific interactions was realized, and the topographical image quality and the specific bonding capability of the tip were not affected.

Algorithms↗

PubMed1999

Optimization of adhesion mode atomic force microscopy resolves individual molecules in topography and adhesion.

The force sensor of an atomic force microscope (AFM) is sensitive enough to measure single molecular binding strengths by means of a force-distance curve. In order to combine high-force sensitivity with the spatial resolution of an AFM in topography mode, adhesion mode has been developed. Since this mode generates a force-distance curve for every pixel of an image, the measurement speed in liquid is limited by the viscous drag of the cantilever. We have equipped our adhesion mode AFM with a cantilever that has a low viscous drag in order to reach pixel frequencies of 65 Hz. Optimized filtering techniques combined with an auto-zero circuitry that reduces the drift in the deflection signal, limited high- and low-frequency fluctuations in the height signal to 0.3 nm. This reduction of the height noise, in combination with a thermally stabilized AFM, allowed the visualization of individual molecules on mica with an image quality comparable to tapping mode. The lateral resolution in both the topography and the simultaneously recorded adhesion image are only limited by the size of the tip. Hardware and software position feedback systems allows individual molecules to be followed in time during more than 30 min with scan sizes down to 60 x 60 nm2.

Evaluation Studies as Topic↗

PubMed1998

Simultaneous height and adhesion imaging of antibody-antigen interactions by atomic force microscopy.

Specific molecular recognition events, detected by atomic force microscopy (AFM), so far lack the detailed topographical information that is usually observed in AFM. We have modified our AFM such that, in combination with a recently developed method to measure antibody-antigen recognition on the single molecular level (Hinterdorfer, P., W. Baumgartner, H. J. Gruber, K. Schilcher, and H. Schindler, Proc. Natl. Acad. Sci. USA 93:3477-3481 (1996)), it allows imaging of a submonolayer of intercellular adhesion molecule-1 (ICAM-1) in adhesion mode. We demonstrate that for the first time the resolution of the topographical image in adhesion mode is only limited by tip convolution and thus comparable to tapping mode images. This is demonstrated by imaging of individual ICAM-1 antigens in both the tapping mode and the adhesion mode. The contrast in the adhesion image that was measured simultaneously with the topography is caused by recognition between individual antibody-antigen pairs. By comparing the high-resolution height image with the adhesion image, it is possible to show that specific molecular recognition is highly correlated with topography. The stability of the improved microscope enabled imaging with forces as low as 100 pN and ultrafast scan speed of 22 force curves per second. The analysis of force curves showed that reproducible unbinding events on subsequent scan lines could be measured.

Aluminum Silicates↗