PubMed Health⌕ Search

Biomedical subjects

Osamu Terasaki

Publications and source records attributed to Osamu Terasaki.

At least 19 recordsLinked to original sources
PubMed2006

Complex zeolite structure solved by combining powder diffraction and electron microscopy.

Many industrially important materials, ranging from ceramics to catalysts to pharmaceuticals, are polycrystalline and cannot be grown as single crystals. This means that non-conventional methods of structure analysis must be applied to obtain the structural information that is fundamental to the understanding of the properties of these materials. Electron microscopy might appear to be a natural approach, but only relatively simple structures have been solved by this route. Powder diffraction is another obvious option, but the overlap of reflections with similar diffraction angles causes an ambiguity in the relative intensities of those reflections. Various ways of overcoming or circumventing this problem have been developed, and several of these involve incorporating chemical information into the structure determination process. For complex zeolite structures, the FOCUS algorithm has proved to be effective. Because it operates in both real and reciprocal space, phase information obtained from high-resolution transmission electron microscopy images can be incorporated directly into this algorithm in a simple way. Here we show that by doing so, the complexity limit can be extended much further. The power of this approach has been demonstrated with the solution of the structure of the zeolite TNU-9 (|H9.3|[Al9.3Si182.7O384]; ref. 10) with 24 topologically distinct (Si,Al) atoms and 52 such O atoms. For comparison, ITQ-22 (ref. 11), the most complex zeolite known to date, has 16 topologically distinct (Si,Ge) atoms.

Journal Article↗
PubMed2006

An analytical approach to determine the pore shape and size of MCM-41 materials from X-ray diffraction data.

The pore shape and size of MCM-41 were studied analytically by comparing the observed powder X-ray diffraction intensities with that derived from the MCM-41 crystal structure models, with two different pore shapes, a hexagon and a circle. The powder diffraction patterns from the as-synthesized and the calcined MCM-41 were measured by a synchrotron radiation at SPring-8, Japan. The MCM-41 structure with circular and hexagonal pore shapes explains well for the as-synthesized and the calcined MCM-41 crystals, respectively. The pore size and boundary obtained by this approach agree with those obtained from an N2 gas adsorption measurement combined with the Fourier synthesized density map.

Journal Article↗
PubMed2006

Complete shape retention in the transformation of silica to polymer micro-objects.

Controlled morphogenesis and shape replication are challenges for several rapidly developing fields of materials science. Indeed, although complex forms have been generated by the condensation of inorganic matter in organized media, the shaping of plastic matter on the micrometre scale is still limited to simple forms that are typically obtained as inverse replicas of channel-like cavities and colloidal crystals. Here we report the fabrication of individual plastic micro-objects that follow an elaborate design and are faithful copies of nanoporous inorganic morphotypes. The direct replica method produces an unprecedented library of curved geometrical solids made of plastics, such as cones, bicones, hollow cylinders, rings, test tubes, clubs and vases. The shape retention of the original structures on the microscale and the creation of a new nanostructure produced objects with homogeneous nanopores of 7 nm and cylindrical microcavities as large as 1 microm. This strategy of shape transcription from one material to another opens new perspectives in microfabrication, separation, anchorage and storage of chemical and biological species. Until now it has not been possible to realize such transformations.

Evaluation Study↗
PubMed2005

Self-assembly of designed oligomeric siloxanes with alkyl chains into silica-based hybrid mesostructures.

A novel self-assembly route to ordered silica-organic hybrids using well-defined siloxane oligomers with alkoxy functionality and covalently attached alkyl chains has been investigated. Various hybrid mesostructures were obtained by hydrolysis and polycondensation without the use of any structure-directing agents. The oligomers 1(Cn), having an alkylsilane core and three branched trimethoxysilyl groups, formed highly ordered lamellar phases when n = 14-18, while those with shorter alkyl chains formed cylindrical assemblies, slightly distorted two-dimensional (2D) hexagonal structures (n = 6-10), and a novel 2D monoclinic structure (n = 12). Furthermore, the mixtures of 1(Cn) with different chain lengths yielded well-ordered 2D hexagonal phases, possibly due to the better packing of the precursors. The hybrids consisting of cylindrical assemblies were converted to ordered porous silica with tunable pore sizes upon calcination to remove organic groups. The liquid-state 29Si NMR analysis of the hydrolysis and polycondensation processes of 1(Cn) revealed a unique intramolecular reaction yielding primarily the oligomer with a tetrasiloxane ring which is a new class of amphiphilic molecule having both self-assembling ability and high cross-linking ability. We also found that the mesostructure (lamellar or 2D hexagonal) was strictly controlled by varying the number of siloxane units per alkyl chain. These results provide a deeper understanding of the present self-assembly process that is strongly governed by the molecular packing of oligosiloxane precursors.

Magnetic Resonance Spectroscopy↗
PubMed2005

Three-dimensional low symmetry mesoporous silica structures templated from tetra-headgroup rigid bolaform quaternary ammonium surfactant.

Two kinds of highly ordered mesoporous silica materials (FDU-11, FDU-13) with novel three-dimensional (3-D) tetragonal and orthorhombic structures were synthesized by using tetra-headgroup rigid bolaform quaternary ammonium surfactant [(CH(3))(3)NCH(2)CH(2)CH(2)N(CH(3))(2)CH(2)(CH(2))(11)OC(6)H(4)C(6)H(4)O(CH(2))(11)CH(2)N(CH(3))(2)CH(2)CH(2)CH(2)N(CH(3))(3).4Br] (C(3-12-12)(-)(3)) as a template under alkaline conditions. High-resolution transmission electron microscopy (HRTEM), small-angle X-ray scattering (SAXS), and X-ray diffraction (XRD) show that mesoporous silica FDU-11 has primitive tetragonal P4/mmm structure with cell parameters a = b = 8.46 nm, c = 5.22 nm, and c/a ratio = 0.617. N(2) sorption isotherms show that calcined FDU-11 has a high BET surface area of approximately 1490 m(2)/g, a uniform pore size of approximately 2.72 nm, and a pore volume of approximately 1.88 cm(3)/g. Mesoporous silica FDU-13 has primitive orthorhombic Pmmm structure. The cell parameters are a = 9.81, b = 5.67, and c = 3.66 nm. N(2) sorption isotherms show that calcined FDU-13 has a high BET surface area of 1210 m(2)/g, a uniform mesopore size of approximately 1.76 nm, and a large pore volume of approximately 1.83 cm(3)/g. Such low symmetries for 3-D mesostructures (tetragonal and orthorhombic system) have not been observed before even in amphiphilic liquid crystals, which maybe resulted from an oblate aggregation of the bolaform surfactant and its strong electrostatic interaction with inorganic precursor. A probable mechanism has been proposed for the formation of such a 3-D low symmetrical mesostructure. These results will further extend the synthesis of mesoporous materials and may open up new opportunities for their new applications in catalysis, separation, and nanoscience.

Journal Article↗
PubMed2005

Synthesis and structural identification of a highly ordered mesoporous organosilica with large cagelike pores.

Using 1,2-bis(trimethoxysilyl)ethane as organosiloxane precursor and a triblock copolymer surfactant, Pluronic F127, as template, a highly ordered mesoporous organosilica with large cagelike pores has been successfully synthesized. Its structure was resolved to be 3-D cubic Fmm by high-resolution transmission electron microscopy. The intergrowth of hexagonal close-packed and cubic close-packed phases was observed in this material. The effect of different siliceous precursors on the mesostructure was also investigated.

Ethane↗
PubMed2005

Characterization of chiral mesoporous materials by transmission electron microscopy.

By using transmission electron microscopy (TEM), the chirality of novel mesoporous materials has been studied. In addition, a computer simulation that uses a simple structural model was employed. The existence of chiral channels inside a tubelike material was confirmed by the observation of fringes along the length of the tubes. The chiral pitch of the channels was measured from the intermittent period, the chirality (right- or left-handed) was determined from the tilt direction of a tube compared with the direction of incident electrons and the curvature direction of the curved intermitted fringes as viewed in the TEM images.

Absorption↗
PubMed2004

Fine structures of zeolite-Linde-L (LTL): surface structures, growth unit and defects.

High-resolution electron microscopy (HREM) has been used to image the surface structure of nano- and micrometer-sized synthetic crystals of zeolite-Linde-L (LTL). Columnar holes and rotational, nano-sized, wheel-like defects were observed within the crystals, where the hole has a minimum size equal to that of the rotational defect. Predictions of surface structure from atomistic computer simulation concur with the observations from HREM and provide insight into the crystal growth mechanism of perfect and defective LTL. Analysis of the energetics of the formation of rotational defect structures reveals that the driving force for defect creation is thermodynamic and furthermore, the rotational defects could be created in high concentrations. Formation of a columnar hole is found to be slightly energetically unfavourable and therefore we speculate that the incidence of both rotational and nano-sized vacancy defects is strongly dependent on kinetic factors and reaction conditions. The morphology of nano- and microcrystalline LTL is contradistinct and we use insights from simulation to propose an explanation of the disparity in crystal shape.

Journal Article↗
PubMed2004

Bis(2-methylimidazolium) hydroxodiphosphatoaluminium.

The title compound, (C4H7N2)2[AlP2O7(OH)], is a one-dimensional extended-chain aluminophosphate prepared by a solvothermal synthesis from an alcohol system. The infinite [AlP2O7(OH)]2- chains composed of AlO4, PO2(=O)2 and PO2(=O)(OH) tetrahedra are linked via hydrogen bonds to the 2-methylimidazolium cations.

Journal Article↗
PubMed2004

Synthesis and characterization of chiral mesoporous silica.

Chirality is widely expressed in organic materials, perhaps most notably in biological molecules such as DNA, and in proteins, owing to the homochirality of their components (d-sugars and l-amino acids). But the occurrence of large-scale chiral pores in inorganic materials is rare. Although some progress has been made in strategies to synthesize helical and chiral zeolite-like materials, the synthesis of enantiomerically pure mesoporous materials is a challenge that remains unsolved. Here we report the surfactant-templated synthesis of ordered chiral mesoporous silica, together with a general approach for the structural analysis of chiral mesoporous crystals by electron microscopy. The material that we have synthesized has a twisted hexagonal rod-like morphology, with diameter 130-180 nm and length 1-6 micro m. Transmission electron microscopy combined with computer simulations confirm the presence of hexagonally ordered chiral channels of 2.2 nm diameter winding around the central axis of the rods. Our findings could lead to new uses for mesoporous silica and other chiral pore materials in, for example, catalysis and separation media, where both shape selectivity and enantioselectivity can be applied to the manufacturing of enantiomerically pure chemicals and pharmaceuticals.

Journal Article↗