PubMed Health⌕ Search

Biomedical subjects

P Ducheyne

Publications and source records attributed to P Ducheyne.

At least 19 recordsLinked to original sources
PubMed1992

Acoustic emission during fatigue of porous-coated Ti-6Al-4V implant alloy.

Acoustic emission (AE) events and event intensities (e.g., event amplitude, counts, duration, and energy counts) were recorded and analyzed during fatigue loading of uncoated and porous-coated Ti-6Al-4V. AE source location, spatial filtering, event, and event intensity distributions were used to detect, monitor, analyze, and predict failures. AE provides the ability to spatially and temporally locate multiple fatigue cracks, in real time. Fatigue of porous-coated Ti-6Al-4V is governed by a sequential, multimode fracture process of: transverse fracture in the porous coating; sphere/sphere and sphere/substrate debonding; substrate fatigue crack initiation; slow and rapid substrate fatigue crack propagation. Because of the porosity of the coating, the different stages of fracture within the coating occur in a discontinuous fashion. Therefore, the AE events generated are intermittent and the onset of each mode of fracture in the porous coating can be detected by increases in AE event rate. Changes in AE event rate also correspond to changes in crack extension rate, and may therefore be used to predict failure. AE offers two distinct advantages over conventional optical and microscopic methods of analyzing fatigue cracks--it is more sensitive and it can determine the time history of damage progression. The magnitude of the AE event intensities increased with increasing stress. Failure mechanisms are best differentiated by analyzing AE event amplitudes. Intergranular fracture and microvoid coalescence generated the highest AE event amplitudes (100 dB), whereas, plastic flow and friction generated the lowest AE event amplitudes (55-65 dB). Fractures in the porous coating were characterized by AE event amplitudes of less than 80 dB.

Alloys↗
PubMed1992

The effect of phase differences on the time-dependent variation of the zeta potential of hydroxyapatite.

The osteoconductive nature of calcium phosphate ceramics (CPC) follows from several proven effects, such as a direct bone attachment and enhanced bone tissue formation. Mechanisms leading to these phenomena are still largely undiscovered. Specifically, little is known about the CPC surface and cell-driven reactions. These atomic and molecular level events are involved in tissue attachment and enhanced tissue formation. It is hypothesized that the zeta potential of these ceramics is directly related to the surface reactivity governing osteoconductivity. As a first step in our analysis, the zeta potential of stoichiometric and Ca-deficient hydroxyapatite was determined as a function of immersion time. It is concluded that, under the conditions of the experiment, the observations support the hypothesis in a dual way. First, the absolute values of the zeta potential which were measured are related to electrokinetic potentials known to cause substantial effect on the cellular activities and bone tissue formation when applied exogenously. Second, the magnitude and duration of the changes in zeta potential are related to an ion exchange between the hydrated layer around the ceramic and the ceramic surface, and a net precipitation of new material. If these findings could be confirmed in other solutions, i.e., solutions with a substantially equivalent composition as the fluids in developing bone tissue, a basis would be provided to explain the bridging of the ceramic surface with the surrounding developing tissue.

Biocompatible Materials↗
PubMed1992

The mechanisms of passive dissolution of titanium in a model physiological environment.

The surface chemistry, oxidation, and disolution kinetics of titanium were measured to establish the mechanisms of passive dissolution in physiological environments. Titanium thin films were immersed in 8.0 mM ethylenediamine-tetraacetic acid in simulated interstitial electrolyte (EDTA/SIE) and maintained at 37 degrees C, 10% O2, 5% CO2 and 7.2 pH for periods of time up to 3200 h (133 days). Two immersion schemes were employed: the integral sequentially determined the titanium released into a solution of accumulated dissolution products; and the differential continuously replenished the test solution. The solutions were analyzed for titanium by electrothermal atomic absorption spectrometry (EAAS), and the sample surfaces were analyzed by Auger electron spectroscopy (AES) and x-ray photoelectron spectroscopy (XPS) to determine oxide composition, stoichiometry, and thickness. Prior to immersion two types of hydroxyl (OH) groups were distinguished on the TiO2 surface. Upon immersion, the chemistry of the surface changed as a function of immersion: the presence of OH groups increased and P (nonelemental) was detected at the surface. The dissolution kinetics obeyed a two-phase logarithmic model, where the transition between phases occurred simultaneously with the adsorption of the P-containing species. The dissolution kinetics depended on surface reactions, electric field strength, and molecular diffusion. These mechanisms explain the observed dependence of dissolution kinetics on the properties of the surface oxide and solution ligands.

Edetic Acid↗
PubMed1992

The fracture toughness of titanium-fiber-reinforced bone cement.

Fracture of the poly(methyl methacrylate) bone cement mantle can lead to the loosening and ultimate failure of cemented total joint prostheses. The addition of fibers to the bone cement increases fracture resistance and may reduce, if not eliminate, in vivo fracturing. This study discusses the effect of incorporating titanium (Ti) fibers on fracture toughness. Essential characteristics of the composite bone cement included a homogeneous and uniform fiber distribution, and a minimal increase in apparent viscosity of the polymerizing cement. Ti fiber contents of 1%, 2%, and 5% by volume increased the fracture toughness over non-reinforced bone cement by up to 56%. Bone cements of two different viscosities were used as matrix material, but when reinforced with the same fiber type and content, they showed no difference in fracture toughness. Four different fiber aspect ratios (68, 125, 227, 417) were tested. At 5% fiber content, there was no statistically significant dependence of fracture toughness on fiber aspect ratio. Scanning electron microscopy revealed important toughening mechanisms such as fiber/matrix debonding, local fracture path alteration, and ductile fiber deformation and fracture. Fiber fracture was evidence that the critical fiber length was exceeded. The surfaces of the Ti fibers were rough and irregular, indicating that a high degree of mechanical interlock between matrix and fiber was likely. The energy absorption contribution of plastic deformation and ductile fracture is absent in brittle fibers, like carbon, but is a distinction of the Ti fibers used in this study.

Biocompatible Materials↗
PubMed1992

Bone tissue growth enhancement by calcium phosphate coatings on porous titanium alloys: the effect of shielding metal dissolution product.

The possible mechanism of minimization of prosthesis-derived bone growth inhibitors by shielding of the metal and the reduction, if not elimination, of the associated metal dissolution was investigated. Titanium, aluminium and vanadium release rates were determined in vitro for Ti alloy specimens both with and without a calcium phosphate coating. Ti orderly oriented wire mesh (OOWM) porous coatings on Ti-6Al-4V substrates were used as the metal specimens. Half of the specimens were coated with a 75 microns calcium phosphate ceramic (CPC coating). Seven reference (OOWM) and seven coated (OOWM-CPC) specimens were immersed and placed along with seven control solutions for various periods in an incubator maintained at 37 degrees C and 5% CO2 - air atmosphere. Whereas the reference solutions showed a Ti release increasing as a function of time, the solutions that had the CPC-coated specimens contained no measurable amounts of titanium. The Al in solution around the CPC-coated specimens was significantly greater than the concentration around non-coated specimens. The Al, however, did not increase significantly with time, at least up to 4 wk immersion. The ceramic coating had a small beneficial effect on V concentration. In the absence of a significant adverse effect of Ti on local bone tissue formation, we focus on the Al data of our study. The possible adverse effect of this element is well documented. The calcium phosphate coating produced a significant increase of biological fixation, yet at the same time a greater Al release into solution, calling into question the significance of CPC coating in shielding adverse metal passive dissolution to explain enhanced bone growth [corrected].

Alloys↗
PubMed1992

Hydration and preferential molecular adsorption on titanium in vitro.

Surface sensitive spectroscopies, Auger electron and X-ray photoelectron (XPS), were used to determine changes in titanium oxide composition, oxide stoichiometry, and adsorbed surface species as a function of exposure to human serum in a balanced electrolyte (serum/SIE) and 8.0 mM ethylenediaminetetraacetic acid in a balanced electrolyte (EDTA/SIE) at 37 degrees C. Before immersion, the oxide was near ideal TiO2, covered by two types of hydroxyl groups: acidic OH(s) with oxygens doubly coordinated to titanium, and basic Ti-OH groups singly coordinated. After extended exposure to both solutions, up to 5000 h (ca. 208 d), the surface concentration of OH groups increased and non-elemental P appeared. The P LVV Auger transition and P 2p spectra indicated the peak positions were similar to reference phosphate compounds. The adsorbed phosphate species were presumed to be either Ti-H2PO4 or Ti-HPO4-. The XPS data suggested that a lipoprotein and/or glycolipid film was adsorbed to the specimens exposed to serum/SIE. Analysis of the preferential lipoprotein/glycolipid adsorption using electrostatic bonding concepts contributed to the refinement of the hierarchical model for the Ti-tissue interface. The salient features are that Ti metal is not in direct contact with the biological milieu, rather there is a gradual transition from the bulk metal, near-stoichiometric oxide, Ca and P substituted hydrated oxide, adsorbed lipoproteins and glycolipids, proteoglycans, collagen filaments and bundles to cells.

Adsorption↗
PubMed1992

Field distributions in the rat tibia with and without a porous implant during electrical stimulation: a parametric modeling.

Expeditious post-operative ingrowth of bone is necessary for clinically successful fixation of porous joint prostheses. Electrical or electromagnetic fields to stimulate bone growth into porous implants have been used; however, they produced nonconvincing data. This was partially attributable to the lack of quantification of the localized electric fields produced in the pores of the implants. Therefore, this study set out: i) to quantify the local electric field values induced into the surface pores of nonconducting implants by "capacitive" coupling and to determine the magnitude of the macroscopically applied capacitively coupled electrical currents to induce specific electric field amplitudes in the pores, ii) to identify the important dielectric properties of the implant-tissue interface, and iii) to create the basis for successfully applying electrical fields in an animal model to stimulate bone ingrowth. A finite element method was used to calculate the electric field gradients and current densities present in a rat tibia modeled with a porous intramedullary implant when capacitively stimulated. Results indicated that while the current density in the pores are reduced in comparison to the region just outside the pore by about one order of magnitude, a significant current density still exists in the pore region. Furthermore, the presence of the implant increases the current densities in the trabecular bone while decreasing these values in the cortical bone. Replacing the trabecular bone in the pore by saline increases the current density in the pore by three-fold, but decreases the voltage gradient by a similar factor.

Animals↗
PubMed1992

Bioactive ceramic prosthetic coatings.

The concept of bioactive ceramic coatings on macroscopically smooth prostheses tries to reconcile opposing principles: the ceramic with beneficial bone tissue growth effects is used as a coating since it does not have sufficient strength and toughness to be used by itself as a prosthesis material. But strength is still an issue since the coating is the primary means of transferring stresses from prosthesis to surrounding tissues. The interface between the metal core and ceramic surface is then critical, since it essentially depends on the strength characteristics of the ceramic. Conversely, when the ceramic coating is used as a means to enhance bone-tissue formation around and into the prosthesis surface, thereby helping to establish a mechanical form of retention, the adhesion of ceramic coating to metallic substrate is not critical. The optimum characteristics of the ceramic are then those that produce the highest effect on bone-tissue growth rates immediately after surgery. The rate of bioactivity is related to the chemical reactivity of the material causing interfacial dissolution, precipitation, and ion exchange reactions. Furthermore, it also appears to depend on a substratum function affecting mineral precipitation, collagen deposition, and cellular differentiation and proliferation.

Biocompatible Materials↗
PubMed1991

Compositional variations in the surface and interface of calcium phosphate ceramic coatings on Ti and Ti-6Al-4V due to sintering and immersion.

The compositions of the surface and the interface of calcium phosphate ceramic (CPC) coatings electrophoretically deposited and sintered on titanium or its alloy, were determined by scanning Auger electron spectroscopy before and after 4 wk of immersion in a simulated physiological solution. In the CPC coating-metal interfaces, the phosphorus diffused beyond the titanium oxide layer. The phosphorus concentration in the interface followed a Gaussian distribution for both unalloyed and alloyed titanium. The diffusion depleted P in the ceramic adjacent to the metal. The surface of the ceramic, however, was substantially unchanged. A major change in the compositional depth profiles was induced by immersion: thick and uniform titanium phosphide layers of constant composition were observed on the Ti-based metal substrates.

Alloys↗
PubMed1991

Bioactive glass particulate material as a filler for bone lesions.

Calcium-phosphate ceramic particulates are often used as filler material for enhanced repair of dental bone defects. Although evidence of bone ingrowth in the scaffold of these particles has been described, it is not observed consistently. Fibrous tissue often encapsulates these particles, which can subsequently become dispersed into the surrounding tissues or even exfoliated. The aim of the present study was to evaluate bioactive glass granules (Biogran) as a filler for osseous lesions, and to compare them with two commercially available Hydroxylapatite (HA) granules. The particulates were implanted in the jaws of five beagle dogs, resected and evaluated after 1, 2, 3, 6 and 12 months of implantation. Histological analysis revealed an improvement in repair of all the lesions. A massive osteoconductive bone growth was seen near the walls of the bony cavities, but in greater amounts around the bioactive glass granules than around the HA materials. On top of this massive growth a trabecular bone growth was observed in the centre of the bony cavities. These trabeculae were associated with the glass particles, which exhibited osteophilic properties, while fibrous tissue separated the bone tissue from the HA particles. The centres of many of the particles are excavated, and are subsequently filled by newly formed bone tissue. This internally formed bone tissue is not necessarily connected to the surrounding bone tissue, and functions as a nucleation site for further bone repair. For the mesenchymal cells within the eroded glass particles this inner environment acts as a stimulus to differentiate into osteoblasts and to start their osteogenetic potential. This phenomenon was not observed around the HA materials. If the latter were surrounded by fibrous tissue, disintegration of the surface by giant cells was observed.

Adhesiveness↗
PubMed1990

A fractographic analysis of in vivo poly(methyl methacrylate) bone cement failure mechanisms.

Cementing with poly(methyl methacrylate) (PMMA) is a common means of fixing total hip prostheses. Bone cement fails mechanically, and subsequent loosening frequently requires correction via revision surgery. An initial step in optimizing bone cement properties is to establish which properties are critical to the material's in vivo performance. The objectives were to discern the critical in vivo failure mechanisms of bone cement. Fracture surfaces of bone cement specimens that failed in vivo were compared with fatigue and rapid fracture surfaces created in vitro. In vivo fracture processes of bone cement were positively identified and explained by the elucidation of PMMA fracture micromechanisms. The ex vivo fracture surfaces are remarkably similar to in vitro fatigue fracture surfaces. The fractographic data document that the primary in vivo failure mechanism of bone cement is fatigue, and the fatigue cracks grow by developing a microcraze shower damage zone. Agglomerates of BaSO4 particles can be implicated in some bone cement failures, large flaws or voids in vivo can lead to a rapid, unstable fracture, pores in the PMMA mass have a clear influence on a propagating crack, and wear of the fracture surfaces occurs, and may produce PMMA debris, exacerbating bone destruction.

Aged↗
PubMed1990

A parametric study of the factors affecting the fatigue strength of porous coated Ti-6A1-4V implant alloy.

The high cycle fatigue strength of porous coated Ti-6A1-4V is approximately 75% less than the fatigue strength of uncoated Ti-6A1-4V. This study separates the effects of three parameters thought to be responsible for this reduction: interfacial geometry, microstructure, and surface alterations brought about by sintering. To achieve the goal of one parameter variations, hydrogen-alloying treatments, which refined the lamellar microstructure of beta-annealed and porous coated Ti-6A1-4V, were formulated. The fatigue strength of smooth-surfaced Ti-6A1-4V subjected to hydrogen-alloying treatments is 643-669 MPa, significantly greater than the fatigue strength of beta-annealed Ti-6A1-4V (497 MPa) and also greater than the fatigue strength of pre-annealed, equiaxed Ti-6A1-4V (590 MPa). The fatigue strength of porous coated Ti-6A1-4V, however, is independent of microstructure. This leads to the conclusion that the notch effect of the surface porosity does not allow the material to take advantage of the superior fatigue crack initiation resistance of a refined alpha-grain size. Thus, sinternecks acts as initiated microcracks and fatigue of porous coated Ti-6A1-4V is propagation controlled.

Alloys↗
PubMed1990

Calcium phosphate ceramic coatings on porous titanium: effect of structure and composition on electrophoretic deposition, vacuum sintering and in vitro dissolution.

Bioactive calcium phosphate ceramics (CPC) guide bone formation along their surface. This property is conceptually attractive from the viewpoint of enhancing early bone tissue formation in porous metal coatings. The various studies conducted to exploit this idea, however, reveal a considerable variability of the effect. This suggests material- and processing-induced parametric influences. Thus this study focuses on the formulation of model porous metal-CPC materials for use in one-parametric analyses of material factors. Easily reproducible, porous metals with a uniform porous structure and CPC coating are made with orderly oriented wire mesh (OOWM) porous metal coatings and electrophoretically deposited CPC films. The deposition of the ceramic can be hampered by adsorbed water. Subsequent vacuum sintering leads to several phase transformations: hydroxyapatite is transformed to a mixture of oxyhydroxyapatite and tetracalcium phosphate; the underlying titanium promotes the beta- to alpha-tricalcium phosphate transformation; and Ca-deficient hydroxyapatite is transformed to a mixture containing oxyhydroxyapatite and alpha- and beta-tricalcium phosphate. These phase transformations provoke a considerable increase of in vitro dissolution in 0.05 M tris buffered physiological solution.

Biocompatible Materials↗
PubMed1990

Effect of calcium phosphate coating characteristics on early post-operative bone tissue ingrowth.

The synthesis of model porous metal-CPC materials, and their use in one-parametric studies of bone tissue ingrowth enhancement were considered. By using the same starting calcium-deficient hydroxyapatite powder, three different coatings, CAP1, CAP2 and CAP3, were obtained of thicknesses 50 +/- 5, 75 +/- 5 and 75 +/- 5 microns, respectively. CAP1 and 2 were either the starting powder mixed in a 3:1 ratio CPC: poly(lactic acid) or the powder by itself. The CAP3 coating was the result of a thermal treatment producing a mixture of oxyhydroxyapatite, alpha- and beta-tricalcium phosphate. Orderly oriented wire mesh porous coated specimens were implanted, along with the same specimens lined with CAP 1, 2 or 3. Subsequently, the total of 156 specimens was retrieved at 2, 4 or 6 wk, and tested mechanically and processed for histomorphometry. The data produced considerable evidence for the CPC-dependent enhancement of bone tissue ingrowth in porous metals immediately after implantation. They prove that the materials processing of CPC coatings influences the resulting biological behaviour substantially. Furthermore, they support the hypothesis that ceramic dissolution is a causative factor on the bone tissue growth enhancement mechanisms.

Animals↗
PubMed1989

Interfacial analysis of fiber-reinforced bioactive glass dental root implants.

Bioactive glass can form an effective bond with bone. Essential for this connection are the interfacial reactions which lead to the development of a Si-rich film covered by a CaP-rich film. The presence of these layers can be demonstrated clearly by EDX analysis of fiber-reinforced bioactive glass and bulk bioactive glass implants installed for 4 and 16 months in the partial edentulous jaws of beagle dogs. EDX analysis reveals three types of microchemical interface. The first type develops when the implant is bonded to bone. Here, a smooth transition of the CaP profile can be observed between bioactive glass and the bone, thus providing for a compositional gradient between the implant and the surrounding tissues. The second type is seen when the implant surface is surrounded by fibrous tissue. This causes a discontinuity in the CaP profile. The third type is characterized by a gradual decrease in the Ca and P concentrations across the interface, caused by the presence of Ca and P in the fibrous tissue near the implant surface. This suggests that the interface is dynamic in time and transforms to a functionally better optimized interface. EDX analysis does not reveal any metal fiber ion contamination of the outer glass rim of the implant. When stainless-steel or wrought Co-Cr alloy is exposed to the surrounding fluids, the interfacial osteogenesis is disturbed, possibly by a synergistic effect of glass ions and metal ions. Exposure of titanium does not interfere with this osteogenesis. The bone bonding can also be influenced by surgical trauma. However, with precise implantation techniques, an enhancement of bone growth by osteoconductivity can be measured.

Animals↗
PubMed1988

The effect of plasma-sprayed calcium phosphate ceramic coatings on the metal ion release from porous titanium and cobalt-chromium alloys.

Bone tissue ingrowth in porous materials is enhanced by the deposition of bioactive calcium phosphate ceramic linings onto the pore walls. These bioactive coatings can be deposited using several methods which yield a variety of coating efficiencies and thereby influence the mechanisms and kinetics of ion release from the metal. We analyzed the effect of plasma-spraying hydroxyapatite onto titanium and cobalt-chromium alloys by measuring the release of Ti, Al, V, Co, and Cr in vitro. Plasma-sprayed coatings significantly reduced the Ti and Al release from titanium-based alloy specimens. The tendencies of release from the cobalt-based specimens are less pronounced. The data substantiate that neither localized enhanced passive dissolution of metal ions nor ceramic shielding of the metal occurs. The Scanning Auger Electron Microprobe Spectroscopic data suggest that the dissipation of thermal and kinetic energy of the ceramic particle at the time of impact can produce compositional and structural changes in the metal surfaces. The resulting effects are significant for the titanium alloy but less significant for the Co-Cr alloy system.

Alloys↗
PubMed1988

Histological and histomorphometrical analysis of bioactive glass and fibre reinforced bioactive glass dental root implants.

Bioactive glass has the ability to bond with bone, but it cannot be used as a load bearing device due to its limited mechanical properties. By reinforcing bioactive glass with a ductile second phase, a structurally reliable material is obtained. The aim of the present study was to evaluate histologically and morphometrically the interfacial behaviour of submerged composite dental root implants. Therefore, bulk and composite implants were subgingivally installed in the partially edentulous jaws of Beagle dogs and harvested after 4 and 16 months. Histologically, the connection between the implants and bone tissue could be clearly demonstrated. This bone connection is mainly located at the cortical bone level. In the vicinity of the infraalveolar nerve a fibrous tissue contact was found. It is shown that surgical trauma, motion at the glass to tissue interface, and gross ion dissolution from the material adversely affect the interfacial osteogenesis. If these factors are controlled, bone bonding is found over a larger area than the initial area of contact between the implant and bone tissue. This means that bone grows out along the implant surface, starting from the initial contact area. No difference was observed between the interfacial behaviour of bulk bioactive glass and intact fibre reinforced bioactive glass implants.

Animals↗