Biomedical subjects

Pentti Kalliokoski

Publications and source records attributed to Pentti Kalliokoski.

6 recordsLinked to original sources

PubMed2004

Detection of mouse and rat urinary aeroallergens with an improved ELISA.

BACKGROUND: Risk analysis of laboratory animal work presupposes allergen monitoring with sensitive methods. Commercial ELISA kits have recently become available for the detection of mouse (Mus m 1) and rat (Rat n 1) urinary allergen from settled dust samples and air samples with high allergen levels. OBJECTIVE: Our aims were to enhance the sensitivities of the commercial ELISA kits for low aeroallergen levels (less than 1 ng/m(3)) and to test these methods with air samples collected from an animal facility. METHODS: Personal and stationary air samples were collected from an animal facility during various tasks of laboratory animal work and from various premises of the animal facility. RESULTS: The sensitivities of the ELISA assays were improved with a careful choice of analysis parameters and reagents. The detection limits of 0.1 ng/m(3) for Mus m 1 and 0.8 ng/m(3) for Rat n 1 were established. The sensitized assays enabled detection of mouse and rat aeroallergens also from premises in which animals or dirty cages were not present during sampling. CONCLUSION: These sensitive assays will help to perform risk assessment in laboratory animal work. However, there remains a lack of standardized analytic procedures and occupational exposure limits for laboratory animal allergens.

Air Pollutants, Occupational↗

PubMed2004

Potentially pathogenic, slow-growing mycobacteria released into workplace air during the remediation of buildings.

Construction workers' exposure to airborne viable mycobacteria was studied during the remediation of three moldy and two nonmoldy buildings. Furthermore, the concentrations of airborne fungal and actinobacterial spores were determined. The samples for the microbial analyses were collected using a six-stage impactor and an all-glass impinger sampler, and by filter sampling. Specific mycobacteria media and nonselective media were used for the cultures. The samples were cultured for the total numbers of rapidly growing and slow-growing mycobacteria, and the isolates obtained were identified to the genus or species level. Mycobacteria were recovered from the air during the remediation of two of the moldy buildings and one nondamaged building. Concentrations of mycobacteria up to 160 cfu/m3 were detected. A total of 43 mycobacterial isolates was recovered. Most of the isolates were slow-growers, only two rapid-growing strains being detected. The 38 identified isolates belonged to potentially pathogenic species, including Mycobacterium avium complex, M. scrofulaceum, and M. fortuitum, and to saprophytic species, including M. nonchromogenicum and M. terrae. Mycobacteria were the most often detected in samples taken with a six-stage impactor. They were found in buildings with both high and low concentrations of fungi. In conclusion, mycobacteria, both potentially pathogenic and saprophytic species, may be released into the indoor air during the remediation of buildings.

Air Pollution, Indoor↗

PubMed2004

Evaluation of exposure to man-made vitreous fibers by nasal lavage.

The objectives of this study were to develop a biomonitoring method for the assessment of exposure to man-made vitreous fibers (MMVF), to examine the level of exposure to MMVF in the prefabricated house industry, and to study nasal inflammatory reactions and respiratory symptoms associated with MMVF among workers. Nasal lavage was performed on workers from two factories, and concentrations of MMVF were measured by electron microscopy. Cytokines (IL-6, IL-8, TNF-alpha, and IFN-gamma) were also assayed and inflammatory cells (lymphocytes, eosinophils, neutrophils, and macrophages) were counted microscopically. Concentrations of airborne fibers (longer than 5 microm) were measured for comparison. Moreover, the exposure to MMVF and the related symptoms were studied with a structured questionnaire. In nasal lavage samples, the mean concentration of MMVF (length >1.5 microm) was 3260 f/ mL in Factory 1, 1680 f/mL in Factory 2, and below 500 f/mL in the control group. About 52% of the retained fibers were longer than 100 microm. The group-specific mean concentrations of MMVF in nasal lavage samples correlated with production rates and airborne fiber levels in both plants. The airborne concentrations of MMVF both in the breathing zone and fixed-point samples were low (below 0.1 f/cm(3)). No significant differences in the biological response (inflammatory cells, cytokines) were found between the groups exposed and the control group. The workers complained of some irritation of the skin, eyes, and upper respiratory tract, which could be reduced by appropriate protective equipment. It is concluded that nasal lavage can be used as a biomonitoring method in the assessment of MMVF exposure.

Air Pollution, Indoor↗

PubMed2002

Low-flow active and passive sampling of VOCs using thermal desorption tubes: theory and application at an offset printing facility.

While air sampling techniques using adsorbent-based collection, thermal desorption and chromatographic analysis have found a niche in ambient air sampling, occupational applications have been more limited. This paper evaluates the use of thermal desorption techniques for low flow active and passive sampling configurations which allow conveniently long duration sampling in occupational settings and other high concentration environments. The use of an orifice enables flows as low as 0.5 ml min(-1) and sampling periods up to several days without significant biases. A model is used to predict sampling rates of a passive sampler encompassing an orifice, a void space, glass wool, and the adsorbent. Laboratory and field tests conducted at a commercial offset printing facility, which contained a variety of volatile organic compounds (primarily aromatic but also a few chlorinated and terpene compounds at levels from 1 to 67,000 microg m(-3)), are used to evaluate the approach. Tenax GR and Carbosieve SIII, both singly and together, were employed as adsorbents. Side-by-side tests comparing high flow, low flow and passive samplers show excellent agreement and high linearity (r = 0.95) for concentrations spanning nearly five orders of magnitude. Active samplers were tested at flows as low as 0.5 ml min(-1), compared to typical flows up to 40 ml min(-1). Passive samplers demonstrated a linear range and agreement with predictions for adsorbate loadings from approximately 1 ng to nearly 10 microg. Using a chemical mass balance receptor model, concentrations in the facility were apportioned to solvents, inks and other indoor and outdoor sources. Overall, the use of low flow active and passive sampling approaches employing thermal desorption techniques provides good performance and tremendous flexibility that facilitates use in many applications, including workplace settings.

Adsorption↗

PubMed2002

Diffusive uptake in passive and active adsorbent sampling using thermal desorption tubes.

Low flow active sampling techniques collecting vapors and gases using thermally desorbable adsorbents are now feasible and desirable in many applications as they permit long integration times, the potential for miniaturized sampling configurations, and other advantages. At very low air flow rates (< 1 ml min(-1)), diffusive uptake on adsorbents in conventional sorbent tubes may equal or exceed the active (pumped) uptake rate, and even at low flow rates (1-4 ml min(-1)), diffusive uptake may significantly bias measurements. Thus, corrections to account for the diffusive flux or means to limit the diffusive uptake are needed in low flow applications. This paper presents (1) a theoretical analysis of the role of diffusive and advective uptake for several sampling geometries of tube-type samplers; (2) experimental confirmation using both laboratory and field studies; (3) estimates of the tortuosity and porosity of the glass wool packing used to retain the adsorbent, parameters needed to estimate diffusive fluxes in passive and active sampling; (4) a demonstration that orifice-equipped low flow active samplers can reduce diffusive uptake and improve precision, and (5) a model predicting the saturated adsorbent layer that helps to account for the gradual decline in uptake rates seen in passive sampling. Diffusive uptake will depend on the tube configuration and diffusion coefficient of the substance of interest, but for conventional sampling tubes (0.4-0.5 cm id, 1.5 cm air gap), sample flow rates should be maintained above 1 to 4 ml min(-1) to keep errors below 5%. Laboratory experiments showed close agreement with theoretical calculations, and the field study using 1 to 4 d sampling periods and 0.3 ml min(-1) flows demonstrated that the orifice-equipped samplers essentially eliminated diffusive uptake. No significant practical difficulties are encountered using orifices, e.g., pressure drop is minimal. Experimental estimates of tortuosity (0.79 +/- 0.02) and porosity (0.92 +/- 0.10) of the glass wool packing (0.3 cm length) represent relatively little resistance to diffusion; however, variation in the packing and adsorbent placement can degrade the precision achievable by passive samplers. Diffusion barriers, consisting most simply of an orifice, may be used to lower the diffusive uptake. A needle-type orifice permits flows below 0.1 ml min(-1) and is suitable for sampling periods as long as several weeks, and it provided greater precision than conventional open-ended sampling tubes (8% compared to 13%). Finally, the gradual decrease in diffusive fluxes often seen in passive sampling is attributed to additional resistance posed by a saturated adsorbent layer, in agreement with a simple model based on total VOCs and specific adsorptivity of the adsorbent.

Adsorption↗

PubMedDate not supplied

Laboratory and field testing of particle size-selective sampling methods for mineral dusts.

The performances of eight sampling devices were tested with mineral dusts in the laboratory and in a talc production plant. The IOM sampler was chosen as the reference method for inhalable dust, and the IOM samplers provided with the porous plastic foam media were used as the reference methods for both the thoracic and respirable aerosols. The other size-selective instruments tested included the Respicon virtual impactor, the optical GRIMM aerosol monitor, and a two-stage cascade impactor with cut points of 10 and 4 microm. The 37-mm cassettes were also included both as open- and closed-face versions. The study confirmed the usability of the IOM samplers for mineral dust, not only in its original version for the inhalable fraction but also its modified versions for the thoracic and respirable fractions. A high correlation with the two-stage impactor results is an indication of good reproducibility. The results increased the evidence that the 37-mm cassette is a poor indicator of inhalable aerosol. The concentrations obtained with both cassette methods were not only systematically too low but also showed large collection efficiency variability. Therefore, the results cannot be corrected by using correction factors. The concentrations of inhalable aerosol measured with the Respicon were generally low, but its performances for the thoracic and respirable fractions were closer to those for the reference samplers. The results also indicate that the GRIMM monitor is well-suited for such mineral dust determinations when very good accuracy is not required, but the immediate availability of the result is more important.

Air Pollutants, Occupational↗