Biomedical subjects

Petros G Koutsoukos

Publications and source records attributed to Petros G Koutsoukos.

6 recordsLinked to original sources

PubMed2006

Calcium sulfate precipitation in the presence of water-soluble polymers.

The effect of four different polymers on the precipitation of calcium sulfate was investigated in the present work. The degree of inhibition was estimated from measurements of the calcium ion activity and from specific solution conductivity measurements in the supersaturated solutions during the course of the precipitation process. The effects of polyacrylic acid (PAA, three different polymers with average molecular weight 2000, 50,000, and 240,000, respectively) and of a co-polymer of PAA with polystyrene sulfonic acid (PSA, average molecular weight<20,000) were investigated with respect to their effect on the kinetics of spontaneous precipitation of calcium sulfate salts. The results of the kinetics experiments suggested that the spontaneous precipitation from supersaturated calcium sulfate solutions at 25 degrees C yielded exclusively calcium sulfate dihydrate (gypsum) both in the absence and in the presence of the polymeric additives. The induction times, preceding the formation of the solid increased in all cases in the presence of the polymeric additives. Polymer concentrations as low as 2.0 ppm increased induction time from practically zero to 10 min. The rates of precipitation were reduced according to the solutions content in the polymers added and precipitation was completely suppressed in the presence of 6.0 ppm of the polymers tested, depending on their molecular weight. The lower the molecular weight of PAA, the more efficient was the threshold inhibition and the stronger the reduction of the rates of spontaneous precipitation. PSA yielded the poorest inhibition efficiency in comparison with the PAA, possibly because of the relatively lower affinity of the sulfonate groups for the calcium ions of the surface of the solid forming. The kinetics results analysis assuming Langmuir-type adsorption of the polymeric molecules on the growing supercritical gypsum nuclei showed different affinity for the polymers tested in agreement with the respective inhibition efficiency, in the order: PAA1>PAA2>PSA>PAA3. The presence of the polymers in the supersaturated solutions resulted in modification of the precipitated gypsum crystals morphology.

Journal Article↗

PubMed2006

Adsorption of atrazine on soils: model study.

The adsorption of the widely used herbicide atrazine onto three model inorganic soil components (silica gel, gamma-alumina, and calcite (CaCO(3)) was investigated in a series of batch experiments in which the aqueous phase equilibrated with the solid, under different solution conditions. Atrazine did not show discernible adsorption on gamma-alumina (theta=25 degrees C, 3.8<pH<12.1) or calcite (theta=25 degrees C, 7.7<pH<11.7). Significant and completely reversible adsorption from solutions was found for silica gel suspensions. The adsorption isotherms obtained for atrazine uptake on silica gel particles were best fitted with the Freundlich model. An increase of the ionic strength of the electrolytic solution induced an increase of the surface concentration of atrazine on silica gel, indicating significant electrostatic interactions between atrazine and silica gel particles, possibly through interaction with the surface silanol groups of the solid substrate. Increase of the pH value of the electrolyte solution from 6 to 9 considerably decreased the amount of atrazine adsorbed on the silica gel substrate. Decrease of the solution pH from 6 to 3 had only a slight effect on the surface concentration of the adsorbed atrazine. The adsorption of atrazine on silica gel increased when the temperature was decreased from 40 to 25 degrees C, an indication that the adsorption is exothermic. The calculated enthalpy of adsorption ( approximately 10 kJ/mol) indicates that the uptake at the solid-liquid equilibrium pH (6.1) was largely due to physisorption.

Journal Article↗

PubMed2006

The interaction of diphosphonates with calcitic surfaces: understanding the inhibition activity in marble dissolution.

The rates of dissolution of calcitic Carrara marble have been reported to be significantly reduced in alkaline pH (pH 8.25) at 25 degrees C in the presence of (1-hydroxyethylidene)-1,1 diphosphonic acid (HEDP). The adsorption takes place at the calcite/water interface at the double layer through the interaction of charged surface species with the charged solution species of the adsorbate. The present work focused on obtaining a better understanding of the interaction of the calcite surface with HEDP. Calculations were performed according to the triple layer model, assuming the formation of surface complexes between the charged surface species of calcite and the species of HEDP dominant at pH 8.25. According to the model, the adsorbed species are located at the inner Helmholtz plane of the electrical double layer. Strong lateral interactions between the adsorbed species were suggested and were corroborated from the calculation of the respective energy, which was equal to 69 kJ mol(-1). The adsorption isotherm was consistent with the proposed model at low surface coverage values, while discrepancies between the values experimentally measured and the predicted were found at higher adsorbate concentrations. The deviations from the predicted values were attributed to the fact that HEDP adsorption on calcite resulted in the formation of multiple layers. The model explained adequately the changes in the zeta-potential values of calcite in the presence of HEDP in the solution which resulted in charge reversal upon adsorption.

Journal Article↗

PubMed2006

In vitro evaluation for potential calcification of biomaterials used for staple line reinforcement in lung surgery.

Bovine pericardium (BPC) and polytetrafluoroethylene (PTFE) have been widely used to reinforce staple lines in lung resection. Since limited information regarding the calcification of these biomaterials is available, we undertook an in vitro study to evaluate their calcification potential. Commercially available BPC and PTFE biomaterials were evaluated and compared with custom-prepared BPC tissue. In vitro calcification was performed via submersion in supersaturated solution in a double-walled glass reactor at 37.0 degrees C +/- 0.1 degrees C, pH 7.4 +/- 0.1, mimicking most ion concentrations of human blood plasma. In processing of calcification, the pH decrease of the solution simulated the addition of consumed H(+), Ca(2+), and PO(4)(3-) ions from titrant solutions, the concentrations of which were based on the stoichiometry of octacalcium phosphate. The molar ion addition with time was recorded, and the initial slope of the curve was computed for each experiment. The rate of calcification developed (molar calcium phosphate ion addition rate per time and total surface area) (R) was computed after that with respect to the relative supersaturation (sigma) used in each experiment. R for custom-prepared BPC tissues was found to be in the range of 0.19 +/- 0.08 to 0.52 +/- 0.19 (n = 17) in sigma range of 0.72 to 1.42. Commercial BPC was found to be 0.016 to 0.052 (n = 4), and PTFE was 0.005 to 0.05 (n = 8) in the same sigma range. Both clinically applied biomaterials, BPC and PTFE, seemed to be calcified with rates of at least one order of magnitude lower than the custom-prepared BPC tissue. This data suggested that BPC and PTFE biomaterials showed a similar, relatively very low tendency for calcification compared with custom-prepared BPC tissue. Although further studies are necessary, staple line reinforcement by these two biomaterials should be considered safe from the calcification point of view.

Animals↗

PubMed2003

Kinetics of dissolution of powdered Pentelic marble in under-saturated solutions: the role of particle characteristics.

In the present study, the effect of mesopore and particle size distributions on the kinetics of dissolution of powdered Pentelic marble was investigated. Powders obtained by grinding marble slabs in an agate mortar with a pestle (1-3.5 min) were found to be non-porous by nitrogen absorption measurements. These powders, upon dissolution under conditions of constant under-saturation, 25 degrees C, pH 8.25, showed that the kinetics in the absence of mesopores depended on the number of active sites on the exposed surface. Thus, powders consisting of smaller particles, having higher specific surface areas, yielded higher rates of dissolution. Powders, however, which were prepared by grinding marble slabs in a cylinder mill for time periods between 2.0 and 30.0 min, and which exhibited considerable mesoporosity, showed the opposite trend. The rates of dissolution measured for these powders in under-saturated solutions increased with increasing mean particle size and decreased with increasing specific surface area. This finding suggested that the presence of mesopores resulted in lower dissolution rates even though the exposed total surface area was larger. Furthermore, the larger the number of mesopores in a powder sample the slower the corresponding dissolution rates in under-saturated solutions.

Journal Article↗

PubMed2002

Variability of dissolution rates at constant undersaturation.

Dissolution processes play an important role in marble weathering. Investigation of the dissolution kinetics of powdered Pentelic marble, a calcitic natural stone, showed that the rates measured at constant undersaturation decreased with time. It was found that the rate of dissolution decreased sharply to about 50% of the initial value before 5% of the initially suspended powder was dissolved. Past a dissolution extent corresponding to 25% with respect to the suspended solid, the rates of dissolution at the same constant undersaturation reached a stable value corresponding to 20-25% of the initial rate measured. The reduction in the rates of dissolution up to 25% of mass loss was in agreement with the reduction in the total surface area exposed to the solution, suggesting a dependence of the rate on the number of active sites on the surface of the dissolving material. The decrease in the dissolution rates did not depend on the undersaturation of the solution or on the physical characteristics of the particles such as specific surface area, porosity, and particle size distribution. Equal mass losses, with respect to the initially suspended solid, of different samples exhibited the same relative decrease in rate regardless of the conditions of the aqueous solutions.

Journal Article↗