Biomedical subjects

R L Reis

Publications and source records attributed to R L Reis.

At least 19 recordsLinked to original sources

PubMed2007

In vivo response to starch-based scaffolds designed for bone tissue engineering applications.

Our purpose was to evaluate the in vivo endosseous response to three starch-based scaffolds implanted in rats (n = 54). We implanted the three scaffold groups; a 50/50 (wt %) blend of corn starch and ethylene-vinyl alcohol (SEVA-C), the same composition coated with a biomimetic calcium phosphate (Ca-P) layer (SEVA-C/CaP), and a 50/50 (wt %) blend of corn starch and cellulose acetate (SCA), all produced by extrusion with blowing agents, into distal femurs proximal to the epiphyseal plate, for 1, 3, or 6 weeks. Our results showed that at 1 week considerable reparative bone formed around all scaffold groups, although the bone was separated from the scaffold by an intervening soft tissue interfacial zone that comprised two distinct compartments: the surface of the scaffold was occupied by multinucleate giant cells and the compartment between these cells and the surrounding bone was occupied by a streaming fibrous-like tissue. The extracellular matrix of the latter was continuous with the extracellular bone matrix itself, labeled positively for osteocalcin and appeared mineralized by back-scattered electron imaging. All three scaffolds showed a similar tissue response, with the soft tissue interface diminishing with time. No bone contact was observed with SEVA-C at any time point, only transitory bone contact was observed with SEVA-C/CaP at 3 weeks, but SCA exhibited direct bone contact at 6 weeks where 56.23 +/- 6.46% of the scaffold surface was occupied by bone. We conclude that all materials exhibited a favorable bony response and that the rapidly forming initial "connective tissue" seen around all scaffolds was a very early form of bone formation.

Animals↗

PubMed2007

Synthesis and characterization of pH-sensitive thiol-containing chitosan beads for controlled drug delivery applications.

The aim of this study was to develop chitosan-based materials in drug delivery systems possessing covalent attachment of thiol moieties. Thiol-containing chitosan (TCS), found to be soluble in water, was synthesized by graft copolymerization technique. The TCS beads were prepared by using tripolyphoshate, at pH 4.0. The morphology of TCS beads was examined by scanning electron microscopy. The in vitro drug release behavior was studied in phosphate buffer solution at various pH, using indomethacin as a model drug at two different concentrations (0.3 and 0.6% w/w). The release amounts of indomethacin from TCS beads were higher increasing pHs in the dissolution medium. The release rate of indomethacin at pH 7.4 was higher than the release rate at pH 1.4 due to ionization of thiol groups and high solubility of indomethacin in an alkaline medium. These results indicated that the TCS beads may become a delivery system for the controlled release of different drugs wherever pH sensitive mechanics might be useful. This is especially applicable in cases when it is important to minimize drug release in acidic sites, such as in the stomach.

Body Fluids↗

PubMed2006

Modulating bone cells response onto starch-based biomaterials by surface plasma treatment and protein adsorption.

The effect of oxygen-based radio frequency glow discharge (rfGD) on the surface of different starch-based biomaterials (SBB) and the influence of proteins adsorption on modulating bone-cells behavior was studied. Bovine serum albumin, fibronectin and vitronectin were used in single and complex protein systems. RfGD-treated surfaces showed to increase in hydrophilicity and surface energy when compared to non-modified SBB. Biodegradable polymeric blends of cornstarch with cellulose acetate (SCA; 50/50wt%), ethylene vinyl alcohol (SEVA-C; 50/50wt%) and polycaprolactone (SPCL; 30/70wt%) were studied. SCA and SCA reinforced with 10% hydroxyapatite (HA) showed the highest degree of modification as result of the rfGD treatment. Protein and control solutions were used to incubate with the characterized SBB and, following this, MG63 osteoblast-like osteosarcoma cells were seeded over the surfaces. Cell adhesion and proliferation onto SCA was found to be enhanced for non-treated surfaces and on SCA+10%HA no alteration was brought up by the plasma modification. Onto SCA surfaces, BSA, FN and VN single solutions improved cell adhesion, and this same effect was found upscaled for ternary systems. In addition, plasma treated SEVA-C directed an increase in both adhesion and proliferation comparing to non-treated surfaces. Even though adhesion onto treated and untreated SPCL was quite similar, plasma modification clearly promoted MG63 cells proliferation. Regarding MG63 cells morphology it was shown that onto SEVA-C surfaces the variation of cell shape was primarily defined by the protein system, while onto SPCL it was mainly affected by the plasma treatment.

Biocompatible Materials↗

PubMed2006

Microhardness of starch based biomaterials in simulated physiological conditions.

In this work the variation of the surface mechanical properties of starch-based biomaterials with immersion time was followed using microhardness measurements. Two blends with very distinct water uptake capabilities, starch/cellulose acetate (SCA) and starch/poly(epsilon-caprolactone) (SPCL), were immersed in a phosphate buffer solution (PBS) at 37.5 degrees C for various times. The microhardness of the blends decreased significantly ( approximately 50% for SPCL and approximately 94% for SCA), within a time period of 30 days of immersion, reflecting the different hydrophilic character of the synthetic components of the blends. The dependence of microhardness on the applied loading time and load was also analysed and showed a power law dependency for SCA. Water uptake and weight loss measurements were performed for the same immersion times used in the microhardness experiments. The different swelling/degradation behaviour presented by the blends was related to the respective variation in microhardness. Moreover, complementary characterization of the mechanical properties of SCA and SPCL was accomplished by dynamic mechanical analysis (DMA) and creep measurements. Microhardness measurements proved to be a useful technique for characterizing the mechanical behaviour near the surface of polymeric biomaterials, including in simulated physiological conditions.

Biocompatible Materials↗

PubMed2006

A comparative analysis of scaffold material modifications for load-bearing applications in bone tissue engineering.

To facilitate optimal application of appropriate scaffold architectures for clinical trials, there is a need to compare different scaffold modifications under similar experimental conditions. In this study was assessed the effectiveness of poly-e-caprolactone (PCL) scaffolds fabricated by fused deposition modelling (FDM), with varying material modifications, for the purposes of bone tissue engineering. The incorporation of hydroxyapatite (HA) in PCL scaffolds, as well as precalcification through immersion in a simulated body fluid (SBF) to produce a biomimetic apatite coating on the scaffolds, was assessed. A series of in vitro studies spanning 3 weeks as well as in vivo studies utilizing a subcutaneous nude mouse model were carried out. PCL and HA-PCL scaffolds demonstrated increasing tissue growth extending throughout the implants, as well as superior mechanical strength and mineralization, as evidenced by X-ray imaging after 14 weeks in vivo. No significant difference was found between PCL and HA-PCL scaffolds. Precalcification with SBF did not result in increased osteoconductivity and cell proliferation as previously reported. Conversely, tensile forces exerted by tissue sheets bridging adjacent struts of the PCL scaffold caused flaking of the apatite coating that resulted in impaired cell attachment, growth and mineralization. The results suggest that scaffolds fabricated by FDM may have load-bearing applications.

Animals↗

PubMed2005

Entrapment ability and release profile of corticosteroids from starch-based microparticles.

We previously described the synthesis of starch-based microparticles that were shown to be bioactive (when combined with Bioactive Glass 45S5) and noncytotoxic. To further assess their potential for biomedical applications such as controlled release, three corticosteroids with a similar basic structure-dexamethasone (DEX), 16alpha-methylprednisonole (MP), and 16alpha-methylprednisolone acetate (MPA)-were used as models for the entrapment and release of bioactive agents. DEX, MP, and MPA were entrapped into starch-based microparticles at 10% wt/wt of the starch-based polymer and the loading efficiencies, as well as the release profiles, were evaluated. Differences were found for the loading efficiencies of the three corticosteroids, with DEX and MPA being the most successfully loaded (82 and 84%, respectively), followed by MP (51%). These differences might be explained based on the differential distribution of the molecules within the matrix of the microparticles. Furthermore, a differential burst release was observed in the first 24 h for all corticosteroids with DEX and MP being more pronounced (around 25%), whereas only 12% of MPA was released during the same time period. Whereas the water uptake profile can account for this first stage burst release, the subsequent slower release stage was mainly attributed to degradation of the microparticle network. Differences in the release profiles can be explained based on the structure of the molecule, because MPA, a more bulky and hydrophobic molecule, is released at a slower rate compared with DEX and MP. In this work, it is shown that these carriers were able to sustain a controlled release of the entrapped corticosteroids over 30 days, which confirms the potential of these systems to be used as carriers for the delivery of bioactive agents.

Dexamethasone↗

PubMed2005

Study of the influence of beta-radiation on the properties and mineralization of different starch-based biomaterials.

In this work, the effects of beta-radiation are assessed, for the first time, on starch-based biodegradable polymers, with the aim of using it as an alternative sterilization process to the previously studied sterilization methods. Different doses of radiation were used in order to investigate the possibility of using this sterilization technique as a treatment to tailor the surface and bulk properties (namely mechanical) of these polymers. The as-treated substrates were characterized by water-uptake measurements and contact angle (theta) measurements. The mechanical properties of the materials were characterized by tensile tests by means of ultimate tensile strength (UTS) and strain at break (epsilon). The fracture of the surfaces was observed by scanning electron microscopy (SEM). Dynamic mechanical analysis (DMA) was also used to characterize the viscolelastic behavior of the irradiated materials. The main effect of sterilization with beta-radiation over the starch-based polymers seems to be a surface modification by an increase of the hydrophilicity. Nevertheless, because beta-radiation did not significantly affect the mechanical properties, it can be regarded as an effective way of modifying the surface for applications were more hydrophilic surfaces are desirable.

Beta Particles↗

PubMed2005

Physical properties and biocompatibility of chitosan/soy blended membranes.

Blends of polysaccharides and proteins are a source for the development of novel materials with interesting and tailorable properties, with potential to be used in a range of biomedical applications. in this work a series of blended membranes composed by chitosan and soy protein isolate was prepared by solvent casting methodology. in addition, cross-linking was performed in situ with glutaraldehyde solutions in the range 5x10(-3)-0.1 M. Furthermore, the influence of the composition and cross-linking on the degradation behaviour, water uptake and cell adhesion was investigated. The obtained results showed that the incorporation of chitosan, associated to network formation by cross linking, promoted a slight decrease of water absorption and a slower degradability of the membranes. Moreover, direct contact biocompatibility studies, with L929 cells, indicate that the cross-linking enhances the capability of the material to support cell growth.

Absorbable Implants↗

PubMed2005

Effect of starch-based biomaterials on the in vitro proliferation and viability of osteoblast-like cells.

The cytotoxicity of starch-based polymers was investigated using different methodologies. Poly-L-lactic acid (PLLA) was used as a control for comparison purposes. Extracts of four different starch-based blends (corn starch and ethylene vinyl alcohol (SEVA-C), corn starch and cellulose acetate (SCA), corn starch and polycaprolactone (SPCL) and starch and poly-lactic acid (SPLA70) were prepared in culture medium and their toxicity was analysed. Osteoblast-like cells (SaOs-2) were incubated with the extracts and cell viability was assessed using the MTT test and a lactate dehydrogenase (LDH) assay. In addition DNA and total protein were quantified in order to evaluate cell proliferation. Cells were also cultured in direct contact with the polymers for 3 and 7 days and observed in light and scanning electron microscopy (SEM). LDH and DNA quantification revealed to be the most sensitive tests to assess respectively cell viability and cell proliferation after incubation with starch-based materials and PLLA. SCA was the starch blend with higher cytotoxicity index although similar to PLLA polymer. Cell adhesion tests confirmed the worst performance of the blend of starch with cellulose acetate but also showed that SPCL does not perform as well as it could be expected. All the other materials were shown to present a comparable behaviour in terms of cell adhesion showing slight differences in morphology that seem to disappear for longer culture times. The results of this study suggest that not only the extract of the materials but also their three-dimensional form has to be biologically tested in order to analyse material-associated parameters that are not possible to consider within the degradation extract. In this study, the majority of the starch-based biomaterials presented very promising results in terms of cytotoxicity, comparable to the currently used biodegradable PLLA which might lead the biocompatibility evaluation of those novel biomaterials to other studies.

Biocompatible Materials↗

PubMed2005

Chitosan particles agglomerated scaffolds for cartilage and osteochondral tissue engineering approaches with adipose tissue derived stem cells.

It is well accepted that natural tissue regeneration is unlikely to occur if the cells are not supplied with an extracellular matrix (ECM) substitute. With this goal, several different methodologies have been used to produce a variety of 3D scaffolds as artificial ECM substitutes suitable for bone and cartilage tissue engineering. Furthermore, osteochondral tissue engineering presents new challenges since the combination of scaffolding and co-culture requirements from both bone and cartilage applications is required in order to achieve a successful osteochondral construct. In this paper, an innovative processing route based on a chitosan particles aggregation methodology for the production of cartilage and osteochondral tissue engineering scaffolds is reported. An extensive characterization is presented including a morphological evaluation using Micro-Computed Tomography (microCT) and 3D virtual models built with an image processing software. Mechanical and water uptake characterizations were also carried out, evidencing the potential of the developed scaffolds for the proposed applications. Cytotoxicity tests show that the developed chitosan particles agglomerated scaffolds do not exert toxic effects on cells. Furthermore, osteochondral bilayered scaffolds could also be developed. Preliminary seeding of mesenchymal stem cells isolated from human adipose tissue was performed aiming at developing solutions for chondrogenic and osteogenic differentiation for osteochondral tissue engineering applications.

Adipose Tissue↗

PubMed2005

Nano- and micro-fiber combined scaffolds: a new architecture for bone tissue engineering.

One possible interesting way of designing a scaffold for bone tissue engineering is to base it on trying to mimic the biophysical structure of natural extracellular matrix (ECM). This work was developed in order to produce scaffolds for supporting bone cells. Nano and micro fiber combined scaffolds were originally produced from starch based biomaterials by means of a fiber bonding and a electrospinning, two step methodology. The cell culture studies with SaOs-2 human osteoblast-like cell line and rat bone marrow stromal cells demonstrated that presence of nanofibers influenced cell shape and cytoskeletal organization of the cells on the nano/micro combined scaffolds. Moreover, cell viability and Alkaline Phosphatase (ALP) activity for both cell types was found to be higher in nano/micro combined scaffolds than in control scaffolds based on fiber meshes without nanofibers. Consequently, the developed structures are believed have a great potential on the 3D organization and guidance of cells that is provided for engineering of 3-dimensional bone tissues.

Alkaline Phosphatase↗

PubMed2005

The effect of starch-based biomaterials on leukocyte adhesion and activation in vitro.

Leukocyte adhesion to biomaterials has long been recognised as a key element to determine their inflammatory potential. Results regarding leukocyte adhesion and activation are contradictory in some aspects of the material's effect in determining these events. It is clear that together with the wettability or hydrophilicity/hydrophobicity, the roughness of a substrate has a major effect on leukocyte adhesion. Both the chemical and physical properties of a material influence the adsorbed proteins layer which in turn determines the adhesion of cells. In this work polymorphonuclear (PMN) cells and a mixed population of monocytes/macrophages and lymphocytes (mononuclear cells) were cultured separately with a range of starch-based materials and composites with hydroxyapatite (HA). A combination of both reflected light microscopy and scanning electron microscopy (SEM) was used in order to study the leukocyte morphology. The quantification of the enzyme lactate dehydrogenase (LDH) was used to determine the number of viable cells adhered to the polymers. Cell adhesion and activation was characterised by immunocytochemistry based on the expression of several adhesion molecules, crucial in the progress of an inflammatory response. This work supports previous in vitro studies with PMN and monocytes/macrophages, which demonstrated that there are several properties of the materials that can influence and determine their biological response. From our study, monocytes/macrophages and lymphocytes adhere in similar amounts to more hydrophobic (SPCL) and to moderately hydrophilic (SEVA-C) surfaces and do not preferentially adhere to rougher substrates (SCA). Contrarily, more hydrophilic surfaces (SCA) induced higher PMN adhesion and lower activation. In addition, the hydroxyapatite reinforcement induces changes in cell behaviour for some materials but not for others. The observed response to starch-based biodegradable polymers was not significantly different from the control materials. Thus, the results reported herein indicate the low potential of the starch-based biodegradable polymers to induce inflammation especially the HA reinforced composite materials.

Biocompatible Materials↗

PubMed2005

Surface modification of starch based blends using potassium permanganate-nitric acid system and its effect on the adhesion and proliferation of osteoblast-like cells.

The surface modification of three starch based polymeric biomaterials, using a KMnO4/HNO3 oxidizing system, and the effect of that modification on the osteoblastic cell adhesion has been investigated. The rationale of this work is as follows--starch based polymers have been proposed for use as tissue engineering scaffolds in several publications. It is known that in biodegradable systems it is quite difficult to have both cell adhesion and proliferation. Starch based polymers have shown to perform better than poly-lactic acid based materials but there is still room for improvement. This particular work is aimed at enhancing cell adhesion and proliferation on the surface of several starch based polymer blends that are being proposed as tissue engineering scaffolds. The surface of the polymeric biomaterials was chemically modified using a KMnO4/HNO3 system. This treatment resulted in more hydrophilic surfaces, which was confirmed by contact angle measurements. The effect of the treatment on the bioactivity of the surface modified biomaterials was also studied. The bioactivity tests, performed in simulated body fluid after biomimetic coating, showed that a dense film of calcium phosphate was formed after 30 days. Finally, human osteoblast-like cells were cultured on unmodified (control) and modified materials in order to observe the effect of the presence of higher numbers of polar groups on the adhesion and proliferation of those cells. Two of the modified polymers presented changes in the adhesion behavior and a significant increase in the proliferation rate kinetics when compared to the unmodified controls.

Body Fluids↗

PubMed2005

Biological response to pre-mineralized starch based scaffolds for bone tissue engineering.

It is known that calcium-phosphate (Ca-P) coatings are able not only to improve the bone bonding behaviour of polymeric materials, but at the same time play a positive role on enhancing cell adhesion and inducing the differentiation of osteoprogenitor cells. Recently an innovative biomimetic methodology, in which a sodium silicate gel was used as a nucleative agent, was proposed as an alternative to the currently available biomimetic coating methodologies. This methodology is especially adequate for coating biodegradable porous scaffolds. In the present work we evaluated the influence of the referred to treatment on the mechanical properties of 50/50 (wt%) blend of corn starch/ethylene-vinyl alcohol (SEVA-C) based scaffolds. These Ca-P coated scaffolds presented a compressive modulus of 224.6 +/- 20.6 and a compressive strength of 24.2 +/- 2.20. Cytotoxicity evaluation was performed according ISO/EN 10993 part 5 guidelines and showed that the biomimetic treatment did not have any deleterious effect on L929 cells and did not inhibit cell growth. Direct contact assays were done by using a cell line of human osteoblast like cells (SaOS-2). 3 x 10(5) cells were seeded per scaffold and allowed to grow for two weeks at 37( composite function)C in a humidified atmosphere containing 5% CO(2). Total protein quantification and scanning electron microscopy (SEM) observation showed that cells were able to grow in the pre-mineralized scaffolds. Furthermore cell viability assays (MTS test) also show that cells remain viable after two weeks in culture. Finally, protein expression studies showed that after two weeks osteopontin and collagen type I were being expressed by SaOS-2 cells seeded on the pre-mineralized scaffolds. Moreover, alkaline phosphatase (ALP) activity was higher in the supernatants collected from the pre-mineralized samples, when compared to the control samples (non Ca-P coated). This may indicate that a faster mineralization of the ECM produced on the pre-mineralized samples was occurring. Consequently, biomimetic pre-mineralization of starch based scaffolds can be a useful route for applying these materials on bone tissue engineering.

Alkaline Phosphatase↗

PubMed2004

Synthesis and evaluation of novel bioactive composite starch/bioactive glass microparticles.

The aim of the development of composite materials is to combine the most desired properties of two or more materials. In this work, the biodegradable character, good controlled-release properties, and natural origin of starch-based biomaterials are combined with the bioactive and bone-bonding properties of bioactive glass (BG). Novel, bioactive composite starch-BG microparticles were synthesized starting from a blend of starch and polylactic acid (50%/50% wt) with BG 45S5 powder using a simple emulsion method. Morphological and chemical characterization showed that these particles exhibited a spherical morphology with sizes up to 350 microm and that BG 45S5 was incorporated successfully into the composite particles. Upon immersion in a solution simulating body fluids, for periods up to 3 weeks, their bioactive nature was confirmed, as a calcium-phosphate layer resembling biological apatite was formed onto their surface. The short-term cytotoxicity of these materials was also tested by placing 24-h leachables of the materials extracted in culture medium in contact with a fibroblastic cell line (L929) up to 72 h. At this time period, two biochemical tests--MTT and total protein quantification--were performed. The results showed that these materials are not cytotoxic. These results constitute the basis of future encapsulation studies using bone-acting therapeutic agents such as bone morphogenetic proteins or other bone-relevant factors. The particles developed here may be very useful for applications in which controlled release, degradability, and bone-bonding ability are the main requirements.

Animals↗

PubMed2004

Multichannel mould processing of 3D structures from microporous coralline hydroxyapatite granules and chitosan support materials for guided tissue regeneration/engineering.

A three-dimensional composite material was produced from microporous coralline origin hydroxyapatite (HA) microgranules, chitosan fibers and chitosan membrane. Cylindrical HA microgranules were oriented along channel direction within multichannel mould space and aligned particles were supported with fibers and a chitosan membrane. The positive replica of mould channels was clasp fixed to produce thicker scaffolds. Light microphotographs of the developed complex structure showed good adhesion between the HA particles, the fibers and the supporting membrane. The composite material showed 88% (w/w) swelling in one hour and preserved the complex structure of the original material upon long-term incubation in physiological medium. MEM extract test of HA chitosan complex showed no cell growth inhibition and cell viability assay (MTS) indicated over 90% cell viability.

Animals↗

PubMed2004

Immobilisation of catalase on the surface of biodegradable starch-based polymers as a way to change its surface characteristics.

In this study, a specific enzyme catalase was immobilised onto the surface of two different biodegradable materials, starch cellulose acetate (SCA) and starch polycrapolactone (SPCL) blends. This immobilisation was achieved by several different routes, mainly by covalent binding and an adsorption method using as activation agents epichlorohydrin, cyanogen bromide (CNBr), and aminopropyltriethoxysilane. The effect of the coupling pH of the enzyme-support reaction was determined in terms of activity recovery (%). The catalase immobilised on SCA showed higher activity recovery (%) for all the methods used as compared with results obtained with SPCL. The immobilisation process using epichlorohydrin as an activation agent and polyethylenimine as a spacer-arm enhanced the stability and the half-lives at pH 7.0, 30 degrees C, for immobilised catalase on both SCA and SPCL. The half-lives were respectively, 1162 and 870 h compared with other treatments and free enzyme (480 h). The free glycerol present in the immobilisation medium was also a factor that contributed toward the better performance regarding the long-term stability at 30 degrees C and neutral pH. The extension of the morphological modifications on the surface of the materials was observed by scanning electron microscopy. In general, the results indicated that the chemical modification with epichlorohydrin could provide a simple and rather efficient technique to modify the starch-based materials' surface that might be useful in several biomedical applications.

Absorbable Implants↗

PubMed2004

Influence of beta-radiation sterilisation in properties of new chitosan/soybean protein isolate membranes for guided bone regeneration.

Novel chitosan (cts) and soybean protein isolate (SI) blended membranes were prepared. These membranes were produced by solvent casting. Besides combining the advantages of both materials, cts/SI membranes exhibit a biphasic structure that will eventually originate in situ porous formation, through a two-step degradation mechanism. In this particular work the effect of beta-radiation over the properties of these membranes was evaluated. beta-radiation sterilisation was performed at three different doses (25, 50 and 100 kGy) and eventual surface chemical changes were evaluated by Fourier transformed infrared--with attenuated total reflection and contact angle measurements. Moreover, eventual bulk properties changes due to beta-radiation were assessed by means of mechanical tensile tests and water uptake measurements. In general, no substantial changes were detected on the studied properties, with the exception of the surface energy that was found to be slightly increased for higher applied doses.

Beta Particles↗