Biomedical subjects

Reginald B H Tan

Publications and source records attributed to Reginald B H Tan.

6 recordsLinked to original sources

PubMed2006

Dry powder aerosol delivery of large hollow nanoparticulate aggregates as prospective carriers of nanoparticulate drugs: effects of phospholipids.

The present work details the effects of incorporating phospholipids, a major component of lung surfactants, in the formulation of large hollow nanoparticulate aggregates, which are specifically designed to serve as potential carrier particles in inhaled delivery of nanoparticulate drugs. The large hollow aerosol particles (d(g) approximately 10 microm), whose shells are composed of nanoparticulate aggregates, are manufactured via the spray drying of nanoparticulate suspensions under a predetermined operating condition. Polyacrylate and silica nanoparticles of various sizes (20-170 nm), without loaded drugs, are employed as the model nanoparticles. The effects of increasing the phospholipids concentration in the presence of the nanoparticles, and vice versa, on the degree of hollowness and morphology of the spray-dried particles are investigated. Varying the phospholipids concentration in the presence of a constant amount of nanoparticles is found to influence the degree of hollowness, without significantly affecting the particle size distribution and respirable fine particle fraction, of the aerosol particles. The effects of increasing the phospholipids concentration on the degree of hollowness of the spray-dried particles are found to depend on the size and chemical nature of the nanoparticles.

Acrylates↗

PubMed2006

Influence of particle wall adhesion on particle electrification in mixers.

In this work, particle electrification in the Turbula and horizontally oscillating mixers were investigated for adipic acid, microcrystalline cellulose (MCC), and glycine particles. MCC and glycine particles acquired positive electrostatic charges, while adipic acid particles attained negative charges in both mixers. Adipic acid (of sieved size larger than 500 microm), MCC, and glycine particles were monotonically charged to saturated values, and had negligible wall adhesion. On the contrary, the adipic acid particles, both unsieved and sieved but of smaller sieved size fraction, exhibited very different charging kinetics in the horizontally oscillating mixer. These adipic acid particles firstly acquired charges up to a maximum value, and then the charges slowly reduced to a lower saturated value with increasing mixing time. Furthermore, these particles were found to adhere to the inner wall of the mixer, and the adhesion increased with mixing time. Surface specific charge densities for adipic acid particles were estimated based on particle size distribution, and were found to increase with particle mean diameters under the conditions investigated. The results obtained from the current work suggested that electrostatic force enhanced particle-wall adhesion, and the adhered particles can have a significant impact on particle electrification.

Adhesiveness↗

PubMed2006

Life cycle investigation of CO2 recovery and sequestration.

The Life Cycle Assessment of four CO2 recoverytechnologies, combined with nine CO2 sequestration systems, serves to expand the debate of CO2 mitigation methods beyond a single issue-prevention of global warming-to a wider range of environmental concerns: resource depletion, acidic and toxic gases, wastes, etc, so that the overall, and unexpected, environmental impacts may be revealed.

Carbon Dioxide↗

PubMed2006

Impact assessment of waste management options in Singapore.

This paper describes the application of life cycle assessment for evaluating various waste management options in Singapore, a small-island city state. The impact assessment method by SimaPro is carried out for comparing the potential environmental impacts of waste treatment options including landfilling, incineration, recycling, and composting. The inventory data include gases and leachate from landfills, air emissions and energy recovery from incinerators, energy (and emission) savings from recycling, composting gases, and transport pollution. The impact assessment results for climate change, acidification, and ecotoxicity show that the incineration of materials imposes considerable harm to both human health and the environment, especially for the burning of plastics, paper/cardboard, and ferrous metals. The results also show that, although some amount of energy can be derived from the incineration of wastes, these benefits are outweighed by the air pollution (heavy metals and dioxins/furans) that incinerators produce. For Singapore, landfill gases and leachate generate minimal environmental damage because of the nation's policy to landfill only 10% of the total disposed wastes. Land transportation and separation of waste materials also pose minimal environmental damage. However, sea transportation to the landfill could contribute significantly to acidification because of the emissions of sulfur oxides and nitrogen oxides from barges. The composting of horticultural wastes hardly imposes any environmental damage. Out of all the waste strategies, the recycling of wastes offers the best solution for environmental protection and improved human health for the nation. Significant emission savings can be realized through recycling.

Air Pollutants↗

PubMed2005

Selective polymorph transformation via solvent-drop grinding.

A method of inducing specific polymorph transformations is exemplified with two single-component systems, whereby a given crystal form undergoes conversion when subjected to solid state grinding in the presence of a minor quantity of a certain solvent.

Combinatorial Chemistry Techniques↗

PubMed2005

Life cycle assessment of EPS and CPB inserts: design considerations and end of life scenarios.

Expanded polystyrene (EPS) and corrugated paperboard (CPB) are used in many industrial applications, such as containers, shock absorbers or simply as inserts. Both materials pose two different types of environmental problems. The first is the pollution and resource consumption that occur during the production of these materials; the second is the growing landfills that arise out of the excessive disposal of these packaging materials. Life cycle assessment or LCA will be introduced in this paper as a useful tool to compare the environmental performance of both EPS and CPB throughout their life cycle stages. This paper is divided into two main parts. The first part investigates the environmental impacts of the production of EPS and CPB from 'cradle-to-gate', comparing two inserts--both the original and proposed new designs. In the second part, LCA is applied to investigate various end-of-life cases for the same materials. The study will evaluate the environmental impacts of the present waste management practices in Singapore. Several 'what-if' cases are also discussed, including various percentages of landfilling and incineration. The SimaPro LCA Version 5.0 software's Eco-indicator 99 method is used to investigate the following five environmental impact categories: climate change, acidification/eutrophication, ecotoxicity, fossil fuels and respiratory inorganics.

Environmental Monitoring↗