PubMed Health⌕ Search

Biomedical subjects

Richard J Bushby

Publications and source records attributed to Richard J Bushby.

7 recordsLinked to original sources
PubMed2007

A model system to study the insertion of cholesterol into a phospholipid monolayer.

Colloidal probe atomic force microscopy (AFM) was used to study the interaction between a surface bearing tethered cholesterol groups and an egg phosphatidylcholine (egg-PC) monolayer. The cholesterol bearing surface was comprised of a mixed self-assembled monolayer comprised of O-cholesteryl N-(8'-mecapto-3',6'-dioxaoctyl)carbamate (CPEO3) molecules and beta-mercaptoethanol formed on a 20 mum diameter gold-coated silica particle. The egg-PC monolayer was adsorbed onto an octadecylthiol monolayer formed on template-stripped gold. The force between the surfaces, as a function of separation, was measured for surface concentrations of CPEO3 from 0 to 100 mol %. At all concentrations there was a long-range repulsive double-layer force due to weak surface charges. At surface concentrations of CPEO3 from 1 to 29 mol % the interaction on the approach of the surfaces showed a maximum in the repulsive force, followed by a small (2-5 nm) jump into a force minimum corresponding to adhesion of the surfaces. On separation, a normalized pull-off force of 1.0-1.6 mN m(-1) was measured. Over the same concentration range, the calculated interaction energy per CPEO3 molecule decreased from 1.1 +/- 0.2 kT to 0.04 kT. At surface concentrations of 35 mol % and above there was no reproducible adhesion between the cholesterol-bearing surface and the phospholipid monolayer. We attribute the occurrence of short-range attraction and adhesion in the 1-29 mol % regime to the insertion of (some) cholesterol groups into the phospholipid monolayer. At higher surface concentrations the efficiency of insertion is reduced due to steric effects. We discuss the experimental results in the light of the energetics of the insertion of a cholesterol molecule into a lipid bilayer.

Cholesterol↗
PubMed2006

Soft-UV photolithography using self-assembled monolayers.

We report thiol-on-gold self-assembled monolayers (SAMs) that can be photodeprotected using soft UV irradiation (lambda = 365 nm) to yield CO(2)H functionalized surfaces complementing those reported previously, which yielded NH(2) functionalized surfaces. The photolysis of these SAMs were monitored using a combination of surface sensitive techniques. In the SAM environment the photodeprotection yields are lower than those obtained for equivalent reactions in dilute solution. The protected carboxylic acids SAMs are shown to have a low yield approximately 50% due to competing photoreduction reactions of the nitro group. The results from infrared studies show that, as the photolysis progresses, the long chain protected residues reorganize and shield the functional COOH groups, thereby reducing the hydrophilic character of the surface.

Journal Article↗
PubMed2006

Redox enzymes in tethered membranes.

An electrode surface is presented that enables the characterization of redox-active membrane enzymes in a native-like environment. An ubiquinol oxidase from Escherichia coli, cytochrome bo(3) (cbo(3)), has been co-immobilized into tethered bilayer lipid membranes (tBLMs). The tBLM is formed on gold surfaces functionalized with cholesterol tethers which insert into the lower leaflet of the membrane. The planar membrane architecture is formed by self-assembly of proteoliposomes, and its structure is characterized by surface plasmon resonance (SPR), electrochemical impedance spectroscopy (EIS), and tapping-mode atomic force microscopy (TM-AFM). The functionality of cbo(3) is investigated by cyclic voltammetry (CV) and is confirmed by the catalytic reduction of oxygen. Interfacial electron transfer to cbo(3) is mediated by the membrane-localized ubiquinol-8, the physiological electron donor of cbo(3). Enzyme coverages observed with TM-AFM and CV coincide (2-8.5 fmol.cm(-)(2)), indicating that most-if not all-cbo(3) on the surface is catalytically active and thus retains its integrity during immobilization.

Cholesterol↗
PubMed2005

Self-assembly of actin scaffolds at ponticulin-containing supported phospholipid bilayers.

Phospholipid vesicles containing ponticulin have been used to form solid supported and tethered bilayer lipid membranes. The ponticulin serves as both a nucleation site for actin polymerization as well as a binding site for F-actin. Studies of F-actin binding to such bilayers have demonstrated the formation of an in vitro actin scaffold. The dissociation constant for the binding of F-actin filaments to a ponticulin-containing tethered bilayer was found to be 11 +/- 5 nM, indicative of high affinity binding.

Actins↗
PubMed2005

A mild photoactivated hydrophilic/hydrophobic switch.

Surface modification using light is one of the most powerful methods for controlling the physical and chemical properties offunctionalized surfaces. In this paper, we report on systems where soft UV irradiation (lambda = 365 nm) converts a "low" activity fluorocarbon to a "high" activity amine-functionalized surface. An amine-functionalized SAM (self-assembled monolayer) is first masked using a tertiary amine catalyzed reaction with an N-hydroxysuccinimidyl carbonyl reagent. This mild, room-temperature reaction introduces a hydrophobic photocleavable nitrobenzyl "protecting group" terminated with a fluorocarbon end-chain. UV irradiation (lambda = 365 nm) of this hydrophobic/fluorocarbon surface cleaves the nitrobenzyl residue, returning the surface to the original hydrophilic/amine-functionalized state. This provides a mild, generic method of producing surfaces with hydrophilic/hydrophobic patterns or patterned with amine functional residues. Two different protecting groups, one terminated with a single and the other with three fluorocarbon end chains, are compared. In the case of the more bulky protecting group, only a small proportion of the amine residues react, but the surface is equally hydrophobic and the amine residues equally well shielded from further reaction. Surfaces are characterized by X-ray photoelectron spectroscopy, ellipsometry, surface potential, and contact angle measurements. Images of the photopatterned SAMs were obtained using scanning electron microscopy.

Journal Article↗
PubMed2005

Direct electrochemical interaction between a modified gold electrode and a bacterial membrane extract.

A novel electrochemical approach is described for redox-active membrane proteins. A total membrane extract (in the form of vesicles) of Bacillus subtilis is tethered onto gold surfaces modified with cholesterol based thiols. The membrane vesicles remain intact on the surface and do not rupture or fuse to form a planar bilayer. Oxidation/reduction signals are obtained of the natural co-enzyme, menaquinone-7, located in the membrane. The membrane protein, succinate menaquinone oxidoreductase (SQR), remains in the vesicles and is able to reduce fumarate using menaquinone as mediator. The catalysis of the reverse reaction (oxidation of succinate), which is the natural catalytic function of SQR, is almost absent with menaquinone. However, adding the co-enzyme ubiquinone, which has a reduction potential that is about 0.2 V higher, restores the succinate oxidation activity.

Bacillus subtilis↗