Biomedical subjects

Rivelino Montenegro

Publications and source records attributed to Rivelino Montenegro.

3 recordsLinked to original sources

PubMed2005

Coil-reinforced hydrogel tubes promote nerve regeneration equivalent to that of nerve autografts.

Despite spontaneous sprouting of peripheral axons after transection injury, peripheral regeneration is incomplete and limited to short gaps, even with the use of autograft tissue, which is considered to be the "gold" standard. In an attempt to obviate some of the problems associated with autografts, including limited donor tissue and donor site morbidity, we aimed to synthesize a synthetic nerve guidance channel that would perform as well as the nerve autograft. Given that the patency of the nerve guidance channel is critical for repair, we investigated a series of nerve guidance channel designs where patency and the resulting regenerative capacity were compared in a transected rat sciatic nerve injury model. Three tube designs were compared to autograft tissue: plain, corrugated and coil-reinforced tubes of poly(2-hydroxyethyl methacrylate-co-methyl methacrylate). Of the three designs, the coil-reinforced tubes demonstrated superior performance in terms of patency. By electrophysiology and histomorphometry, the coil-reinforced tubes demonstrated outcomes that were comparable to autografts after both 8 and 16 weeks of implantation. The nerve action potential (NAP) velocity and muscle action potential (MAP) velocity for the coil-reinforced PHEMA-MMA tube was 54.6+/-10.1 and 10.9+/-1.3 m/s, respectively at 16 weeks, which was statistically equivalent to those of the autograft at 37.5+/-7.9 and 11.3+/-2.0 m/s. The axon density in the coil-reinforced tube was 2.16+/-0.61x10(4) axons/mm2, which was statistically similar to that of the autograft of 2.41+/-0.62x10(4) axons/mm2 at 16 weeks. These coil-reinforced tubes demonstrated equivalence to autografts for nerve regeneration, demonstrating the importance of channel design to regenerative capacity and more specifically the impact of patency to regeneration.

Action Potentials↗

PubMed2005

Chitin-based tubes for tissue engineering in the nervous system.

The purpose of this study was to investigate chitin and chitosan as potential materials for biodegradable nerve guides. Transparent chitin hydrogel tubes were synthesized, for the first time, from chitosan solutions using acylation chemistry and mold casting techniques. Alkaline hydrolysis of chitin tubes resulted in chitosan tubes, with the extent of hydrolysis controlling the resulting amine content. This, in turn, impacted compressive strength and cell adhesion. Chitosan tubes were mechanically stronger than their chitin origins, as measured by the transverse compressive test, where tubes having degrees of acetylation of 1%, 3%, 18% (i.e. chitosan) and 94% (i.e. chitin) supported loads at a 30% displacement of 40.6 +/- 4.3, 25.3 +/- 4.5, 10.6 +/- 0.8, and 8.7 +/- 0.4 g, respectively. However, the chitin processing methodology could be optimized for compressive strength, by either incorporating reinforcing coils in the tube wall, or air-drying the hydrogel tubes. Chitin and chitosan supported adhesion and differentiation of primary chick dorsal root ganglion neurons in vitro. Chitosan films showed significantly enhanced neurite outgrowth relative to chitin films, reflecting the dependence of nerve cell affinity on the amine content in the polysaccharide: neurites extended 1794.7 +/- 392.0 microm/mm(2) on chitosan films vs. 140.5 +/- 41.6 microm/mm(2) on chitin films after 2 days of culture. This implies that cell adhesion and neurite extension can be adjusted by amine content, which is important for tissue engineering in the nervous system. The methods for easy processing and modification of chitin and chitosan described herein, allow the mechanical properties and cyto-compatibility to be controlled and provide a means for a broader investigation into their use in biomedical applications.

Animals↗

PubMed2003

Novel approaches to polymer blends based on polymer nanoparticles.

Polymer layers can exhibit significantly improved performances if they possess a multicomponent phase-separated morphology. We present two approaches to control the dimensions of phase separation in thin polymer-blend layers; both rely on polymer nanospheres prepared by the miniemulsion process. In the first approach, heterophase solid layers are prepared from an aqueous dispersion containing nanoparticles of two polymers, whereas in the second approach, both polymers are already contained in each individual nanoparticle. In both cases, the upper limit for the dimension of phase separation is determined by the size of the individual nanoparticles, which can be adjusted down to a few tens of nanometres. We also show that the efficiencies of solar cells using two-component particles are comparable to those of devices prepared from solution at comparable illumination conditions, and that they are not affected by the choice of solvent used in the miniemulsion process.

Electric Power Supplies↗