PubMed Health⌕ Search

Biomedical subjects

Robert Jérôme

Publications and source records attributed to Robert Jérôme.

At least 19 recordsLinked to original sources

Thermoresponsive coatings strongly adhering to (semi)conducting surfaces.

Thermoresponsive brushes have been efficiently grafted onto (semi)conductive surfaces by a two-step process. In the first step, poly(N-succinimidyl acrylate) chains have been chemisorbed onto silicon or stainless steel by the electrografting method. Then, these modified electrodes were immersed in isopropylamine in order to transform the grafted chains to the thermoresponsive poly(N-isopropyl acrylamide). The thermal response of these brushes has been shown by AFM. This straightforward grafting process is quite attractive for surface modification in confined media and is thus promising for microfludics application.

Journal Article↗

Ultrathin transparent conductive films of polymer-modified multiwalled carbon nanotubes.

Deposition of multiwalled carbon nanotubes modified by poly(2-vinylpyridine) (CNT-g-P2VP) from aqueous dispersions at low pH is an effective method to prepare homogeneous ultrathin films with a tunable CNTs density. A percolation threshold of 0.25 mug/cm2 and a critical exponent alpha = 1.24 have been found from dc conductivity measurements. The sheet resistance value agrees with the percolation theory for 2D films. According to AFM and electrical measurements, even when only 5% of the surface is covered by CNT-g-P2VPs, the sheet resistance is of the order of 1 MOmega/sq, which indicates that conductivity is imparted by a network of an ultralow density. When the film transmittance decreases down to approximately 70% at 550 nm, the occupied surface area is approximately 15% and sheet resistance falls down to approximately 90 kOmega/sq. These data show that undesired in-plane clustering does not occur upon the dispersion casting of the films and that high-quality networks of CNT-g-P2VPs are built up. The electrosteric stabilization of the CNT-g-P2VP dispersions in water at low pH is at the origin of this desired behavior. Although the multiwalled CNT films prepared in this work are less conductive and less transparent than the SWNTs films, they could find applications, e.g., in touch screens, reflective displays, EMI shielding, and static charge dissipation.

Journal Article↗

Limitations in transplantation of astroglia-biomatrix bridges to stimulate corticospinal axon regrowth across large spinal lesion gaps.

Regrowth of injured axons across rather small spinal cord lesion gaps and subsequent functional recovery has been obtained after many interventions. Long-distance regeneration of injured axons across clinically relevant large spinal lesion gaps is relatively unexplored. Here, we aimed at stimulating long-distance regrowth of the injured corticospinal (CS) tract. During development, an oriented framework of immature astrocytes is important for correct CS axon outgrowth. Furthermore, a continuous growth promoting substrate may be needed to maintain a CS axon regrowth response across relatively large spinal lesion gaps. Hence, we acutely transplanted poly(D,L)-lactide matrices, which after seeded with immature astrocytes render aligned astrocyte-biomatrix complexes (R. Deumens, et al. Alignment of glial cells stimulates directional neurite growth of CNS neurons in vitro. Neuroscience 125 (3) (2004) 591-604), into 2-mm long dorsal hemisection lesion gaps. In order to create a growth promoting continuum, astrocyte suspensions were also injected rostral and caudal to the lesion gap. During 2 months, locomotion was continuously monitored. Histological analysis showed that astrocytes injected into host spinal tissue survived, but did not migrate. None of the astrocytes on the biomatrices survived within the lesion gap. BDA-labeled CS axons did not penetrate the graft. However, directly rostral to the lesion gap, 120.9+/-38.5% of the BDA-labeled CS axons were present in contrast to 12.8+/-3.9% in untreated control animals. The observed anatomical changes were not accompanied by locomotor improvements as analyzed with the BBB and CatWalk. We conclude that although multifactorial strategies may be needed to stimulate long-distance CS axon regrowth, future studies should focus on enhancing the viability of cell/biomatrix complexes within large spinal lesion gaps.

Animals↗

Surface modification of metallic cardiovascular stents by strongly adhering aliphatic polyester coatings.

This article reports on a novel two-step strategy for the coating of cardiovascular stents by strongly adhering biocompatible and biodegradable aliphatic polyesters. First, a precoating of poly(ethylacrylate) (PEA) was electrografted onto the metallic substrate by cathodic reduction of the parent monomer in dimethylformamide (DMF). The electrodeposition of PEA, in a good solvent of it, was confirmed by both Infra-red and Raman spectroscopies. The pendant ester groups of PEA were then chemically reduced into aluminum alkoxides, able to initiate the ring-opening polymerization (ROP) of either D,L-lactide (LA) or epsilon-caprolactone (CL). Growth of biodegradable PLA or PCL coatings from the adhering precoating was confirmed by both Infra-red and Raman spectroscopies, and directly observed by scanning electron microscopy (SEM). This type of coating can act as an anchoring layer for the subsequent casting of drug-loaded polyester films allowing the controlled release of antiproliferative agents for the treatment of in-stent restenosis.

Biocompatible Materials↗

Combination of electrografting and atom-transfer radical polymerization for making the stainless steel surface antibacterial and protein antiadhesive.

A two-step "grafting from" method has been successfully carried out, which is based on the electrografting of polyacrylate chains containing an initiator for the atom transfer radical polymerization (ATRP) of 2-(tert-butylamino)ethyl methacrylate (TBAEMA) or copolymerization of TBAEMA with either monomethyl ether of poly(ethylene oxide) methacrylate (PEOMA) or acrylic acid (AA) or styrene. The chemisorption of this type of polymer brushes onto stainless steel surfaces has potential in orthopaedic surgery. These films have been characterized by ATR-FTIR, Raman spectroscopy, atomic force microscopy (AFM), and measurement of contact angles of water. The polymer formed in solution by ATRP and that one detached on purpose from the surface have been analyzed by size exclusion chromathography (SEC) and (1)H NMR spectroscopy. The strong adherence of the films onto stainless steel has been assessed by peeling tests. AFM analysis has shown that addition of hydrophilic comonomers to the grafted chains decreases the surface roughness. According to dynamic quartz crystal microbalance experiments, proteins (e.g., fibrinogen) are more effectively repelled whenever copolymer brushes contain neutral hydrophilic (PEOMA) co-units rather than negatively charged groups (PAA salt). Moreover, a 2- to 3-fold decrease in the fibrinogen adsorption is observed when TBAEMA is copolymerized with either PEOMA or AA rather than homopolymerized or copolymerized with styrene. Compared to the bare stainless steel surface, brushes of polyTBAEMA, poly(TBAEMA-co-PEOMA) and poly(TBAEMA-co-AA) decrease the bacteria adhesion by 3 to 4 orders of magnitude as revealed by Gram-positive bacteria S. aureus adhesion tests.

Adhesiveness↗

Simple method for the stretching and alignment of single adsorbed synthetic polycations.

Spin-coating of isolated positively charged macromolecules onto mica in the presence of octylamine was found to be a simple and general method of stretching and aligning the macromolecular chains. The contour length and molar mass for the stretched macromolecules can be directly measured by atomic force microscopy, which makes this method a very useful analytical tool. Moreover, the molecular height is increased by co-deposition with octylamine, which drastically improves the molecular resolution and allows even ultrathin polycations to be visualized. The reason for the key role of the octylamine is found in the formation of an ultrathin liquidlike alkylamine film, which reduces the surface energy of mica and weakens the interactions between the surface and the charged macromolecules.

Adsorption↗

Polyolefin matrixes with permanent antibacterial activity: preparation, antibacterial activity, and action mode of the active species.

Poly[2-(tert-butylamino)ethyl methacrylate] (PTBAEMA) belongs to a novel class of water-insoluble biocides. Dispersion of a poly(ethylene-co-butylene)-b-poly[2-(tert-butylamino)ethyl methacrylate] diblock copolymer (PEB-b-PTBAEMA) within low-density polyethylene (LDPE) imparts antimicrobial properties to the polyolefin as assessed by the viable cell counting method against Escherichia coli (E. coli). This diblock copolymer has been synthesized by atom transfer radical polymerization (ATRP) with a poly(ethylene-co-butylene) (PEB) oligomer end-capped by an activated bromide as a macroinitiator for the polymerization of 2-(tert-butylamino)ethyl methacrylate (TBAEMA). Morphological changes of E. coli bacteria in contact with modified LDPE have been observed by transmission and scanning electron microscopy and indicate that the diblock copolymer is bactericide rather than bacteriostatic. Finally, the action mode of the PEB-b-PTBAEMA copolymer more likely relies on the displacement of the Ca(2+) and/or Mg(2+) ions of the outer membrane of the bacteria, which is disorganized and finally disrupted.

Anti-Bacterial Agents↗

In vitro and in vivo analysis of macroporous biodegradable poly(D,L-lactide-co-glycolide) scaffolds containing bioactive glass.

Recent studies have demonstrated the angiogenic potential of 45S5 Bioglass. However, it is not known whether the angiogenic properties of Bioglass remain when the bioactive glass particles are incorporated into polymer composites. The objectives of the current study were to investigate the angiogenic properties of 45S5 Bioglass particles incorporated into biodegradable polymer composites. In vitro studies demonstrated that fibroblasts cultured on discs consisting of specific quantities of Bioglass particles mixed into poly(D,L-lactide-co-glycolide) secreted significantly increased quantities of vascular endothelial growth factor. The optimal quantity of Bioglass particles determined from the in vitro experiments was incorporated into three-dimensional macroporous poly(D,L-lactide-co-glycolide) foam scaffolds. The foam scaffolds were fabricated using either compression molding or thermally induced phase separation processes. The foams were implanted subcutaneously into mice for periods of up to 6 weeks. Histological assessment was used to determine the area of granulation tissue around the foams, and the number of blood vessels within the granulation tissue was counted. The presence of Bioglass particles in the foams produced a sustained increase in the area of granulation tissue surrounding the foams. The number of blood vessels surrounding the neat foams was reduced after 2 weeks of implantation; however, compression-molded foams containing Bioglass after 4 and 6 weeks of implantation had significantly more blood vessels surrounding the foams compared with foams containing no Bioglass at the same time points. These results indicate that composite polymer foam scaffolds containing Bioglass particles retain granulation tissue and blood vessels surrounding the implanted foams. The use of this polymer composite for tissue engineering scaffolds might provide a novel approach for ensuring adequate vascular supply to the implanted device.

Angiogenesis Inducing Agents↗

Poly (D,L-lactic acid) macroporous guidance scaffolds seeded with Schwann cells genetically modified to secrete a bi-functional neurotrophin implanted in the completely transected adult rat thoracic spinal cord.

Freeze-dried poly(D,L-lactic acid) macroporous scaffold filled with a fibrin solution containing Schwann cells (SCs) lentivirally transduced to produce and secrete D15A, a bi-functional neurotrophin with brain-derived neurotrophic factor and neurotrophin-3 activity, and to express green fluorescent protein (GFP) were implanted in the completely transected adult rat thoracic spinal cord. Control rats were similarly injured and then implanted with scaffolds containing the fibrin solution with SCs lentivirally transduced to produce express GFP only or with the fibrin solution only. Transgene production and biological activity in vitro, SC survival within the scaffold in vitro and in vivo, scaffold integration, axonal regeneration and myelination, and hind limb motor function were analyzed at 1, 2, and 6 weeks after implantation. In vitro, lentivirally transduced SCs produced 87.5 ng/24 h/10(6) cells of D15A as measured by neurotrophin-3 activity in ELISA. The secreted D15A was biologically active as evidenced by its promotion of neurite outgrowth of dorsal root ganglion neurons in culture. In vitro, SCs expressing GFP were present in the scaffolds for up to 6 h, the end of a typical surgery session. Implantation of SC-seeded scaffolds caused modest loss of spinal nervous tissue. Reactive astrocytes and chondroitin sulfate glycosaminoglycans were present in spinal tissue adjacent to the scaffold. Vascularization of the scaffold was ongoing at 1 week post-implantation. There were no apparent differences in scaffold integration and blood vessel formation between groups. A decreasing number of implanted (GFP-positive) SCs were found within the scaffold during the first 3 days after implantation. Apoptosis was identified as one of the mechanisms of cell death. At 1 week and later time points after implantation, few of the implanted SCs were present in the scaffold. Neurofilament-positive axons were found in the scaffold. At 6 weeks post-grafting, myelinated axons were observed within and at the external surface of the scaffold. Axons did not grow from the scaffold into the caudal cord. All groups demonstrated a similar improvement of hind limb motor function. Our findings demonstrated that few seeded SCs survived in vivo, which could account for the modest axonal regeneration response into and across the scaffold. For the development of SC-seeded macroporous scaffolds that effectively promote axonal regeneration in the injured spinal cord, the survival and/or total number of SCs in the scaffold needs to be improved.

Animals↗

Synthesis of copolymer brushes endowed with adhesion to stainless steel surfaces and antibacterial properties by controlled nitroxide-mediated radical polymerization.

Novel copolymer brushes have been synthesized by a two-step "grafting from" method that consists of the electrografting of poly(2-phenyl-2-(2,2,6,6-tetramethyl-piperidin-1-yloxy)-ethylacrylate) onto stainless steel, followed by the nitroxide-mediated radical polymerization of 2-(dimethylamino ethyl)acrylate and styrene or n-butyl acrylate, initiated from the electrografted polyacrylate chains. The grafted copolymers were quaternized in order to endow them with antibacterial properties. Peeling tests have confirmed the strong adhesion of the grafted copolymer onto the stainless steel substrate. Quartz crystal microbalance experiments have proven that fibrinogen adhesion is lower on the hydrophilic quaternized films compared to the nonionic counterpart. Such quaternized copolymers exhibit significant antibacterial activity against the Gram-positive bacteria S. aureus and the Gram-negative bacteria E. coli.

Acrylates↗

Freeze-dried poly(D,L-lactic acid) macroporous guidance scaffolds impregnated with brain-derived neurotrophic factor in the transected adult rat thoracic spinal cord.

The effects of poly(D,L-lactic acid) macroporous guidance scaffolds (foams) with or without brain-derived neurotrophic factor (BDNF) on tissue sparing, neuronal survival, axonal regeneration, and behavioral improvements of the hindlimbs following implantation in the transected adult rat thoracic spinal cord were studied. The foams were embedded in fibrin glue containing acidic-fibroblast growth factor. One group of animals received fibrin glue with acidic-fibroblast growth factor only. The foams were prepared by a thermally induced polymer-solvent phase separation process and contained longitudinally oriented macropores connected to each other by a network of micropores. Both foams and fibrin only resulted in a similar gliotic and inflammatory response in the cord-implant interfaces. With BDNF foam, up to 20% more NeuN-positive cells in the spinal nervous tissue close to the rostral but not caudal spinal cord-implant interface survived than with control foam or fibrin only at 4 and 8 weeks after implantation. Semithin plastic sections and electron microcopy revealed that cells and axons more rapidly invaded BDNF foam than control foam. Also, BDNF foam contained almost twice as many blood vessels than control foam at 8 weeks after implantation. Tissue sparing was similar in all three implantation paradigms; approximately 42% of tissue was spared in the rostral cord and approximately 37% in the caudal cord at 8 weeks post grafting. The number of myelinated and unmyelinated axons was low and not different between the two types of foams. Many more axons were found in the fibrin only graft. Serotonergic axons were not found in any of the implants and none of the axons regenerated into the caudal spinal cord. The behavioral improvements in the hindlimbs were similar in all groups. These findings indicated that foam is well tolerated within the injured spinal cord and that the addition of BDNF promotes cell survival and angiogenesis. However, the overall axonal regeneration response is low. Future research should explore the use of poly(D,L-lactic acid) foams, with or without axonal growth-promoting factors, seeded with Schwann cells to enhance the axonal regeneration and myelination response.

Absorbable Implants↗

In vivo characterisation of a novel bioresorbable poly(lactide-co-glycolide) tubular foam scaffold for tissue engineering applications.

Polylactide-co-glycolide (PLGA) foams of tubular shape were assessed for their use as soft-tissue engineering scaffolds in vitro and in vivo. Porous membranes were fabricated by a thermally induced phase separation process of PLGA solutions in dimethylcarbonate. The parameters investigated were the PLGA concentration and the casting volume of solution. Membranes produced from 5 wt/v % polymer solutions and a 6 ml casting volume of polymer solution were selected for fabricating tubes of 3 mm diameter, 20 mm length and a nominal wall thickness of 1.5 mm. Scanning electron microscopy revealed that the structure of the tubular foams consisted of radially oriented and highly interconnected pores with a large size distribution (50-300 microm). Selected tubes were implanted subcutaneously into adult male Lewis rats. Although the lumen of the tubes collapsed within one week of implantation, histological examination of the implanted scaffolds revealed that the foam tubes were well tolerated. Cellular infiltration into the foams, consisting mainly of fibrovascular tissue, was evident after two weeks and complete within eight weeks of implantation. The polymer was still evident in the scaffolds after eight weeks of implantation. The results from this study demonstrate that the PLGA tubular foams may be useful as soft-tissue engineering scaffolds with modification holding promise for the regeneration of tissues requiring a tubular shape scaffold such as intestine.

Absorbable Implants↗