PubMed Health⌕ Search

Biomedical subjects

Robert M J Jacobs

Publications and source records attributed to Robert M J Jacobs.

3 recordsLinked to original sources

Protein interactions studied by SAXS: effect of ionic strength and protein concentration for BSA in aqueous solutions.

We have studied a series of samples of bovine serum albumin (BSA) solutions with protein concentration, c, ranging from 2 to 500 mg/mL and ionic strength, I, from 0 to 2 M by small-angle X-ray scattering (SAXS). The scattering intensity distribution was compared to simulations using an oblate ellipsoid form factor with radii of 17 x 42 x 42 A, combined with either a screened Coulomb, repulsive structure factor, SSC(q), or an attractive square-well structure factor, SSW(q). At pH = 7, BSA is negatively charged. At low ionic strength, I < 0.3 M, the total interaction exhibits a decrease of the repulsive interaction when compared to the salt-free solution, as the net surface charge is screened, and the data can be fitted by assuming an ellipsoid form factor and screened Coulomb interaction. At moderate ionic strength (0.3-0.5 M), the interaction is rather weak, and a hard-sphere structure factor has been used to simulate the data with a higher volume fraction. Upon further increase of the ionic strength (I >or= 1.0 M), the overall interaction potential was dominated by an additional attractive potential, and the data could be successfully fitted by an ellipsoid form factor and a square-well potential model. The fit parameters, well depth and well width, indicate that the attractive potential caused by a high salt concentration is weak and long-ranged. Although the long-range, attractive potential dominated the protein interaction, no gelation or precipitation was observed in any of the samples. This is explained by the increase of a short-range, repulsive interaction between protein molecules by forming a hydration layer with increasing salt concentration. The competition between long-range, attractive and short-range, repulsive interactions accounted for the stability of concentrated BSA solution at high ionic strength.

Animals↗

Applying grazing incidence X-ray reflectometry (XRR) to characterising nanofilms on mica.

Molecularly smooth mica has hitherto not been widely used as a substrate for the X-ray reflectometry (XRR) technique. That is largely due to the difficulty of achieving flatness over a sufficiently large area of mica. Here we show that this difficulty can be overcome by slightly bending the mica substrate over an underlying cylinder; the enhanced rigidity of the bent mica sheet along the axis of the cylinder provides sufficient flatness along this axis for XRR measurements. To test this method, we have employed it to characterise three types of nanofilms on mica in air: (A) Cr-Au thin films; (B) a surface-grown zwitterionic polymer brush; and (C) a Langmuir-Blodgett (LB) phospholipid monolayer, using a table-top X-ray reflectometer. Fitting the obtained reflectivity curves with the standard Parratt algorithm allows us to extract the structural information of the nanofilms (both thickness and apparent roughness). Our simple method points to how XRR may be exploited as a useful characterisation tool for nanofilms on mica.

Journal Article↗

Surfaces designed for charge reversal.

We have created surfaces which switch from cationic at pH < 3 to anionic at pH > 5, by attaching aminodicarboxylic acid units to silica and gold substrates. Charge reversal was demonstrated by monitoring the adsorption of cationic dyes (methylene blue and a tetracationic porphyrin) and an anionic sulfonated porphyrin, at a range of pH using UV-vis absorption and reflection spectroscopy. The cationic dyes bind under neutral conditions (pH 5-7) and are released at pH 1-4, whereas the anionic dye binds under acidic conditions (pH 1-4) and is released at pH 5-7. Gold surfaces were functionalized with two different amphoteric disulfides with short (CH(2))(2) and long (CH(2))(10)CONH(CH(2))(6) linkers; the longer disulfide gave surfaces exhibiting charge reversal in a narrower pH range. Adsorption is much faster on the functionalized gold (t(1/2) = 62 s) than on functionalized silica (t(1/2) = 6900 s), but the final extents of coverage on both surface are similar, for a given dye at a given pH, with maximal coverages of around 2 molecules nm(-)(2). These charge-reversal processes are reversible and can be repeatedly cycled by changing the pH. We have also created surfaces which undergo irreversible proton-triggered charge switching, using a carbamate-linked thiol carboxylic acid which cleaves in acid. These surfaces are versatile new tools for controlling electrostatic self-assembly at surfaces.

Journal Article↗