Biomedical subjects

Rossitza G Alargova

Publications and source records attributed to Rossitza G Alargova.

5 recordsLinked to original sources

PubMed2006

Dispersion stability of colloids in sub- and supercritical water.

Dispersion stability of colloids has been investigated in sub- and supercritical water by measuring the hydrodynamic diffusion coefficients of the particles by means of dynamic light scattering. It is interestingly found that coagulation of the colloids in sub- and supercritical water is a universal phenomenon irrespective of the material of the colloids. Highly charged colloids were found to be more stable in water against high temperature. Numerical analysis reveals that the stability of the colloids at elevated temperature and pressure is primarily governed by the temperature dependence of the dielectric constant of the medium. The effect of the temperature dependence of the ion product of water (pKw) was found to be very little. Surface charge density and Stern potential may change with respect to temperature due to the readjustment of the ion concentration in the diffuse layer through the enhanced ion product and reduced dielectric constant of water. These are the secondary causes of the particle coagulations in sub- and supercritical water.

Journal Article↗

PubMed2006

Viscosity measurements of water at high temperatures and pressures using dynamic light scattering.

The application of dynamic light scattering to measure viscosity of water at high temperatures and pressures is demonstrated. Viscosity was obtained from the translational diffusion coefficient of probe particles dispersed in the medium by the Einstein-Stokes relationship. Measurements were carried out with polystyrene latex, colloidal silica, and colloidal gold. Under a constant pressure of 25 MPa, good agreement was found between the measured and calculated viscosities up to 275 degrees C with the polystyrene latex, 200 degrees C with the colloidal silica, and 297 degrees C with the colloidal gold. It was found that failure of the measurements at high temperatures is ascribed to change in either the dispersion stability or chemical stability of the probe particles. The present results indicate that the technique could also be used for other supercritical fluids having high critical temperature and pressure, such as methanol (T(c) = 239.4 degrees C, P(c) = 8.1 MPa) and ethanol (T(c) = 243.1 degrees C, P(c) = 6.4 MPa).

Chemistry, Physical↗

PubMed2006

Formation of polymer microrods in shear flow by emulsification--solvent attrition mechanism.

Rodlike polymer particles could have interesting properties and could find many practical applications; however, few methods for the production of such particles are available. We report a systematic study of a droplet shearing process for the formation of polymer rods with micrometer or submicrometer diameter and a length of up to tens of micrometers. The process is based on emulsification of a polymer solution under shear, combined with solvent attrition in the surrounding organic medium. The droplets deform and elongate into cylinders, which solidify when the solvent transfers to the dispersion medium. Stopped flow experiments allow distinguishing all stages of the mechanism. The results are interpreted on the basis of the theory of droplet elongation and breakup under shear. The effects of the viscosity ratio and shear stress are matched against the theoretical expectations. The method is simple, efficient, and scalable, and we demonstrate how it can be controlled and modified. The experimental parameters that allow varying the rod size and aspect ratio include shear rate, medium viscosity, and polymer concentration. Examples of the specific properties of the polymer rods, including self-organization, alignment in external fields and in fluid flows, and stabilization of bubbles, droplets, and capsules, are presented.

Emulsions↗

PubMed2004

Foam superstabilization by polymer microrods.

Few foam systems stabilized by solid particles have been reported, and usually the particles have been used in combination with surfactants. We report how foams can be stabilized solely with a new class of anisotropic particles, hydrophobic polymer microrods of diameter less than 1 mum and length of a few tens of micrometers. The obtained foams were extraordinary stable, retaining a constant volume over many days and even surviving drying of most of the free liquid. The bubbles in these foams were sterically stabilized by dense thick "hairy" layers. The rigid intertwined protective shells around the bubbles did not allow the formation of thin films between them. The lifetime of these foams was orders of magnitude longer than the ones stabilized with typical foaming surfactants such as sodium dodecyl sulfate. The addition of sodium dodecyl sulfate led to hydrophilization of the microrods and suppressed the superstabilization effect. Thus, common foaming agents effectively act as defoamers for the ultrastable foams stabilized by microrods.

Letter↗

PubMed2004

Fabrication of "hairy" colloidosomes with shells of polymeric microrods.

Novel colloidosome microcapsules with aqueous gel cores and integral shells of rodlike polymeric particles have been prepared and characterized. The synthesis is based on templating water-in-oil emulsions stabilized by rodlike particles followed by gelling of the aqueous phase, dissolution of the oil phase in ethanol, and redispersion of the obtained colloidosome capsules in water. Such capsules may find applications as vehicles for delivery and controlled release of drugs, cosmetics, and food supplements.

Journal Article↗