Biomedical subjects

S C Wilks

Publications and source records attributed to S C Wilks.

6 recordsLinked to original sources

PubMed2005

Temperature determination using Kalpha spectra from M -shell Ti ions.

The compact multipulse terawatt (COMET) laser facility at LLNL was used to irradiate Al-coated 2-50 microm Ti foils with approximately 10(19) W cm(-2) , 500 fs, 3-6 J laser pulses. Laser-plasma interactions on the front side of the target generate hot electrons with sufficient energy to excite inner-shell electrons in Ti, creating Kalpha emission which has been measured using a focusing spectrometer with spatial resolution aimed at the back surface of the targets. The spatial extent of the emission varies with target thickness. The high spectral resolution (lambda/Deltalambda approximately equal to 3800) is sufficient to measure broadening of the Kalpha emission feature due to the emergence of blueshifted satellites from ionized Ti in a heated region of the target. A self-consistent-field model is used to spectroscopically diagnose thermal electron temperatures up to 40 eV in the strongly coupled Ti plasmas.

Journal Article↗

PubMed2004

High-speed horizontal-path atmospheric turbulence correction with a large-actuator-number microelectromechanical system spatial light modulator in an interferometric phase-conjugation engine.

Results of atmospheric propagation for a high-speed, large-actuator-number adaptive optics system are presented. The system uses a microelectromechanical system- (MEMS-) based spatial light modulator correction device with 1024 actuators. Tests over a 1.35-km path achieved correction speeds in excess of 800 Hz and Strehl ratios close to 0.5. The wave-front sensor was based on a quadrature interferometer that directly measures phase. This technique does not require global wave-front reconstruction, making it relatively insensitive to scintillation and phase residues. The results demonstrate the potential of large-actuator-number MEMS-based spatial light modulators to replace conventional deformable mirrors.

Journal Article↗

PubMed2004

Performance of a phase-conjugate engine implementing a finite-bit phase correction.

The achievable Strehl ratio when a finite-bit correction to an aberrated wave front is implemented is examined. The phase-conjugate engine used to measure the aberrated wave front consists of a quadrature interferometric wave-front sensor, a liquid-crystal spatial light modulator, and computer hardware-software to calculate and apply the correction. A finite-bit approximation to the conjugate phase is calculated and applied to the spatial light modulator to remove the aberrations from the optical beam. The experimentally determined Strehl ratio of the corrected beam is compared with analytical expressions for the expected Strehl ratio and shown to be in good agreement with those predictions.

Journal Article↗

PubMed2001

Effect of plasma scale length on multi-MeV proton production by intense laser pulses.

The influence of the plasma density scale length on the production of MeV protons from thin foil targets irradiated at I lambda(2) = 5 x 10(19) W cm(-2) has been studied. With an unperturbed foil, protons with energy >20 MeV were formed in an exponential energy spectrum with a temperature of 2.5+/-0.3 MeV. When a plasma with a scale length of 100 microm was preformed on the back of the foil, the maximum proton energy was reduced to <5 MeV and the beam was essentially destroyed. The experimental results are consistent with an electrostatic accelerating mechanism that requires an ultrashort scale length at the back of the target.

Journal Article↗

PubMed2001

Fast ignition by intense laser-accelerated proton beams.

The concept of fast ignition with inertial confinement fusion (ICF) is a way to reduce the energy required for ignition and burn and to maximize the gain produced by a single implosion. Based on recent experimental findings at the PETAWATT laser at Lawrence Livermore National Laboratory, an intense proton beam to achieve fast ignition is proposed. It is produced by direct laser acceleration and focused onto the pellet from the rear side of an irradiated target and can be integrated into a hohlraum for indirect drive ICF.

Journal Article↗

PubMed2000

Intense high-energy proton beams from Petawatt-laser irradiation of solids.

An intense collimated beam of high-energy protons is emitted normal to the rear surface of thin solid targets irradiated at 1 PW power and peak intensity 3x10(20) W cm(-2). Up to 48 J ( 12%) of the laser energy is transferred to 2x10(13) protons of energy >10 MeV. The energy spectrum exhibits a sharp high-energy cutoff as high as 58 MeV on the axis of the beam which decreases in energy with increasing off axis angle. Proton induced nuclear processes have been observed and used to characterize the beam.

Journal Article↗