Biomedical subjects
Publications and source records attributed to S Inokoshi.
The interfacial structure of seven dentin adhesive systems was studied morphologically. Argon ion beam etching of an undecalcified section clearly revealed the resin-impregnated demineralized dentin at the adhesive interface of the seven systems when observed under the scanning electron microscope.
V-shaped cervical cavities prepared in monkey teeth were restored with several dentin bonding systems, and the in vivo resin-dentin interfacial structures were observed under the scanning electron microscope using an argon-ion etching technique. The hybrid layer could be clearly observed; its depth was dependent on the conditioner/primer used and tended to be thinner at the deep part of the cavity. Resin tags were also clearly observed, and their structure at the inner part was noted to be rougher than that closer to the tubule orifices. When 37% phosphoric acid gel was used, the tags in the deeper parts of the cavity were much rougher. Hemispherical and spherical roughened structures were observed directly above the tubule orifices, which were thought to be a mixture of dentinal fluid and bonding resin that had flowed out from the tubules. The acidic primer containing maleic acid and HEMA could not remove the smear plugs, and undissolved smear particles were observed in the tubules.
Internal opacity and color changes of several esthetic direct restorative materials were determined using an accelerated test proposed by Asmussen (1981). Five chemically cured composites, seven light-cured composites, and three resin-modified glass-ionomer cements were placed in acrylic rings. After curing, they were left at 37 degrees C for 1 week before baseline measurement, and then stored in 60 degrees C distilled water up to 4 weeks. Color change was determined by a color analyzer, and contrast ratio representing opacity was calculated. All chemically cured composites tested discolored to dark yellow or dark brown after 4 weeks. Opacity decreased for two macrofilled composites. Light-cured composites discolored slightly, but their opacity change was negligible. All resin-modified glass-ionomer cements tested showed an abrupt decrease of opacity at the initial stage, with accompanying darkening of the materials. Opacity decrease was found to be a factor of discoloration for some tooth-colored restorative materials, and might be caused by a refractive index change of the matrix phase of the materials.
The effect of low-pressure (41.8 psi) air abrasion with alumina and glass beads on bonding to tooth substrates was evaluated. Tensile bond strengths of a bonding resin to air-abraded bovine enamel and dentin were measured. Scanning electron microscopy was used to observe (1) air-abraded surfaces, (2) fractured surfaces after the tensile bond test, and (3) interfaces of bonded specimens. Air abrasion with glass beads significantly decreased the bond strengths to enamel and dentin, whereas air abrasion with alumina decreased adhesion to enamel but not to dentin. The air-abraded enamel and dentin surfaces were irregularly roughened, and smear layers were created by air abrasion. Hybrid layers were observed at the interface between the bonding resin and the air-abraded dentin. The SEM photographs suggested that air abrasion may weaken the tooth surfaces, which could account for the decrease of the bond strengths.
Monkey pulpal responses to metal inlays luted with a combination of an adhesive resin and luting composite and conventional dental cements were histopathologically evaluated. Initial pulpal responses caused by re-exposure of the cut dentin surfaces and luting procedure under hydraulic pressure subsided at 90 days after final cementation. There was no significant difference among pulpal reactions to conventional dental cements and a combination of an adhesive resin and luting composite. The adhesive resin coating of freshly cut dentinal walls/floors immediately after cavity preparation seems to provide protection for the dentin and pulp in indirect restorations requiring temporary sealing.
Monkey pulpal responses to four adhesive resin systems used as direct pulp capping agents were histopathologically evaluated at 3, 7, 14, 30, and 60 days after operation. No serious inflammatory reaction of the pulp, such as necrosis or abscess formation, was observed. Slight inflammatory cell infiltration was the main inflammatory reaction of the exposed pulp, and the exposed area became occluded with dentin bridging as the observation period increased. Healing of exposed dental pulp beneath adhesive resin capping slightly differed depending on the materials used.
The purpose of this study was to evaluate selective caries removal using an air-abrasive technique. Alumina powders, glass beads, crushed glass powders, and crushed powders of polycarbonate resin were applied to intact human enamel, dentin, and artificially demineralized dentin (caries-model dentin). Furthermore, the effect of the particle size of abrasives and air pressures on the abraded depths was examined. When alumina powders and glass beads were used, the abraded depths of enamel, dentin, and caries model increased as the particle size and air pressure increased. Alumina powders and crushed glass powders abraded intact enamel and dentin more than the caries-model dentin, whereas glass beads abraded the caries-model dentin more than the intact enamel and dentin. Only crushed powders of polycarbonate resin abraded the caries-model dentin without reducing intact enamel and dentin. With hard particles, such as alumina powders, glass beads, or crushed glass powders, selective caries removal by the air-abrasive technique appeared to be difficult to achieve, even if the particle size and the air pressure were changed. Crushed powders of polycarbonate resin that reduced only the caries-model dentin are harder than caries-model dentin, but softer than intact enamel and dentin. This study elucidated the possibility of selective carious dentin removal with the air-abrasive technique.