Biomedical subjects

S J Peter

Publications and source records attributed to S J Peter.

12 recordsLinked to original sources

PubMed2000

Effects of transforming growth factor beta1 released from biodegradable polymer microparticles on marrow stromal osteoblasts cultured on poly(propylene fumarate) substrates.

Recombinant human transforming growth factor beta1 (TGF-beta1) was incorporated into microparticles of blends of poly(DL-lactic-co-glycolic acid) (PLGA) and poly(ethylene glycol) (PEG) to create a delivery vehicle for the growth factor. The entrapment efficiency of TGF-beta1 in the microparticles containing 5% PEG was 40.3 +/- 1.2% for a TGF-beta1 loading density of 6.0 ng/1 mg of microparticles. For the same loading, 17.9 +/- 0.6 and 32.1 +/- 2.5% of the loaded TGF-beta1 was released after 1 and 8 days, respectively, followed by a plateau for the remaining 3 weeks. Rat marrow stromal cells showed a dose response to TGF-beta1 released from the microparticles similar to that of added TGF-beta1, indicating the activity of TGF-beta1 was retained during microparticle fabrication and after TGF-beta1 release. An optimal TGF-beta1 dosage of 1.0 ng/mL was determined through a 3-day dose response study for maximal alkaline phosphatase (ALP) activity. The TGF-beta1 released from the microparticles loaded with 6.0 ng TGF-beta1/1 mg of microparticles for the optimal dosage of TGF-beta1 enhanced the proliferation and osteoblastic differentiation of marrow stromal cells cultured on poly(propylene fumarate) substrates. The cells showed significantly increased total cell number, ALP activity, and osteocalcin production with values reaching 138,700 +/- 3300 cells/cm(2), 22.8 +/- 1.5 x 10(-7) micromol/min/cell, and 15.9 +/- 1.5 x 10(-6) ng/cell, respectively, after 21 days as compared to cells cultured under control conditions without TGF-beta1. These results suggest that controlled release of TGF-beta1 from the PLGA/PEG blend microparticles may find applications in modulating cellular response during bone healing at a skeletal defect site.

Animals↗

PubMed2000

In vitro and in vivo degradation of porous poly(DL-lactic-co-glycolic acid) foams.

This study investigated the in vitro degradation of porous poly(DL-lactic-co-glycolic acid) (PLGA) foams during a 20-week period in pH 7.4 phosphate-buffered saline (PBS) at 37 degrees C and their in vivo degradation following implantation in rat mesentery for up to 8 weeks. Three types of PLGA 85 : 15 and three types of 50 : 50 foams were fabricated using a solvent-casting, particulate-leaching technique. The two types had initial salt weight fraction of 80 and 90%, and a salt particle size of 106-150 microm, while the third type had 90% initial weight fraction of salt in the size range 0-53 microm. The porosities of the resulting foams were 0.82, 0.89, and 0.85 for PLGA 85 : 15, and 0.73, 0.87, and 0.84 for PLGA 50 : 50 foams, respectively. The corresponding median pore diameters were 30, 50, and 17 microm for PLGA 85: 15, and 19, 17, and 17 microm for PLGA 50 : 50. The in vitro and in vivo degradation kinetics of PLGA 85: 15 foams were independent of pore morphology with insignificant variation in foam weight, thickness, pore distribution, compressive creep behavior, and morphology during degradation. The in vitro foam half-lives based on the weight average molecular weight were 11.1 +/- 1.8 (80%, 106-150 microm), 12.0 +/- 2.0 (90%, 106-150 microm), and 11.6 +/- 1.3 (90%, 0-53 microm) weeks, similar to the corresponding values of 9.4 +/- 2.2, 14.3 +/- 1.5, and 13.7 +/- 3.3 weeks for in vivo degradation. In contrast, all PLGA 50 : 50 foams exhibited significant change in foam weight, water absorption, and pore distribution after 6-8 weeks of incubation with PBS. The in vitro foam half-lives were 3.3 +/- 0.3 (80%, 106-150 microm), 3.0 +/- 0.3 (90%, 106-150 microm), and 3.2 +/- 0.1 (90%, 0-53 microm) weeks, and the corresponding in vivo half-lives were 1.9 micro 0.1, 2.2 +/- 0.2, and 2.4 +/- 0.2 weeks. The significantly shorter half-lives of PLGA 50: 50 compared to 85: 15 foams indicated their faster degradation both in vitro and in vivo. In addition, PLGA 50: 50 foams exhibited significantly faster degradation in vivo as compared to in vitro conditions due to an autocatalytic effect of the accumulated acidic degradation products in the medium surrounding the implants. These results suggest that the polymer composition and environmental conditions have significant effects on the degradation rate of porous PLGA foams.

Animals↗

PubMed2000

In vitro degradation of porous poly(L-lactic acid) foams.

This study investigated the in vitro degradation of porous poly(L-lactic acid) (PLLA) foams during a 46-week period in pH 7.4 phosphate-buffered saline at 37 degrees C. Four types of PLLA foams were fabricated using a solvent-casting, particulate-leaching technique. The three types had initial salt weight fraction of 70, 80, and 90%, and a salt particle size of 106-150 microm, while the fourth type had 90% initial weight fraction of salt in the size range 0-53 microm. The porosities of the resulting foams were 0.67, 0.79, 0.91, and 0.84, respectively. The corresponding median pore diameters were 33, 52, 91, and 34 microm. The macroscopic degradation of PLLA foams was independent of pore morphology with insignificant variation in foam weight, thickness, pore distribution, compressive creep behavior, and morphology during degradation. However, decrease in melting temperature and slight increase in crystallinity were observed at the end of degradation. The foam half-lives based on the weight average molecular weight were 11.6+/-0.7 (70%, 106-150 microm), 15.8+/-1.2 (80%, 106-150 microm), 21.5+/-1.5 (90%, 106-150 microm), and 43.0+/-2.7 (90%, 0-53 microm) weeks. The thicker pore walls of foams prepared with 70 or 80% salt weight fraction as compared to those with 90% salt weight fraction contributed to an autocatalytic effect resulting in faster foam degradation. Also, the increased pore surface/volume ratio of foams prepared with salt in the range 0-53 microm enhanced the release of degradation products thus diminishing the autocatalytic effect and resulting in slower foam degradation compared to those with salt in the range 106-150 microm. Formation and release of crystalline PLLA particulates occurred for foams fabricated with 90% salt weight fraction at early stages of degradation. These results suggest that the degradation rate of porous foams can be engineered by varying the pore wall thickness and pore surface/volume ratio.

Biocompatible Materials↗

PubMed2000

Marrow stromal osteoblast function on a poly(propylene fumarate)/beta-tricalcium phosphate biodegradable orthopaedic composite.

The objective of this study was to assess the osteoconductivity of a poly(propylene fumarate)/beta-tricalcium phosphate (PPF/beta-TCP) composite in vitro. We examined whether primary rat marrow stromal cells would attach, proliferate, and express differentiated osteoblastic function when seeded on PPF/beta-TCP substrates. Attachment studies showed that a confluent monolayer of cells had adhered to the substrates within an 8 h time frame for marrow stromal cells seeded at confluent numbers. Proliferation and differentiated function of the cells were then investigated for a period of 4 weeks for an initial seeding density of 42,000 cells/cm2. Rapid proliferation during the first 24 h as determined by 3H-thymidine incorporation was mirrored by an initial rapid increase in total cell number by DNA assay. A lower proliferation rate and a gradual increase in cell number persisted for the remainder of the study, resulting in a final cell number of 128,000 cells/cm2. Differentiated cell function was assessed by measuring alkaline phosphatase (ALP) activity and osteocalcin (OC) production throughout the time course. Both markers of osteoblastic differentiation increased significantly over a 4-week period. By day 28, cells grown on PPF/beta-TCP reached a maximal ALP activity of 11 (+/- 1) x 10(-7) micromol/min/cell, while the OC production reached 40 (+/- 1) x 10(-6) ng/cell. These data show that a PPF/beta-TCP composite exhibits in vitro osteoconductivity similar to or better than that of control tissue culture polystyrene.

Absorbable Implants↗

PubMed1999

Modulation of marrow stromal cell function using poly(D,L-lactic acid)-block-poly(ethylene glycol)-monomethyl ether surfaces.

The adhesion of marrow stromal osteoblasts and the adsorption of fetal bovine serum (FBS) proteins to end-capped poly(D,L-lactic acid) 50:50 (PLA50) of molecular weight 17,000 (PLA5017), non-end-capped PLA50 of molecular weight 11,000 (PLA5011h), and a diblock copolymer made of poly(ethylene glycol)-monomethyl ether of molecular weight 5,000 and PLA50 of molecular weight 20,000 (Me. PEG5-PLA20) were investigated. Cell attachment and proliferation on both PLA50 polymers were equally good. The block copolymer did not allow the proliferation of cells. However, the attached cells were highly differentiated and metabolically active in contrast to the cells on PLA50. Moreover, surface analysis studies using electron spectroscopy revealed that FBS proteins adsorbed well from aqueous solutions to the PLA50 surfaces while they adsorbed substantially less to the block copolymer. These results suggest that Me.PEG-PLA block copolymers may be used to regulate protein adsorption and, therefore, cell adhesion by varying the block composition of the copolymer.

Adsorption↗

PubMed1999

Crosslinking characteristics of an injectable poly(propylene fumarate)/beta-tricalcium phosphate paste and mechanical properties of the crosslinked composite for use as a biodegradable bone cement.

We investigated the crosslinking characteristics of an injectable composite paste of poly(propylene fumarate) (PPF), N-vinyl pyrrolidinone (N-VP), benzoyl peroxide (BP), sodium chloride (NaCl), and beta-tricalcium phosphate (beta-TCP). We examined the effects of PPF molecular weight, N-VP/PPF ratio, BP/PPF ratio, and NaCl weight percent on the crosslinking temperature, heat release upon crosslinking, gel point, and the composite compressive strength and modulus. The maximum crosslinking temperature did not vary widely among formulations, with the absolute values falling between 38 degrees and 48 degrees C, which was much lower than that of 94 degrees C for poly(methyl methacrylate) bone cement controls tested under the same conditions. The total heat released upon crosslinking was decreased by an increase in PPF molecular weight and a decrease in N-VP/PPF ratio. The gel point was affected strongly by the PPF molecular weight, with a decrease in PPF molecular weight more rapidly leading to a gel point. An increase in initiator concentration had the same effect to a lesser degree. The time frame for curing was varied from 1-121 min, allowing the composite to be tailored to specific applications. The compressive strength and compressive modulus values increased with decreasing N-VP/PPF, increasing NaCl content, and increasing BP/PPF ratio. For all formulations, the compressive strength values fell between 1 and 12 MPa, and the compressive modulus values fell between 23 and 265 MPa. These data suggest that injectable PPF/beta-TCP pastes can be prepared with handling characteristics appropriate for clinical orthopedic applications and that the mechanical properties of the cured composites are suitable for trabecular bone replacement.

Biodegradation, Environmental↗

PubMed1999

Synthesis of poly(propylene fumarate) by acylation of propylene glycol in the presence of a proton scavenger.

To synthesize high molecular weight poly(propylene fumarate) (PPF), fumaryl chloride and propylene glycol were reacted in the presence of potassium carbonate, which serves as a proton scavenger. Transesterification of the resulting low molecular weight oligomer led to a polymer with greater molecular weight than those from previous reaction methods without requiring the use of a catalyst. According to two-dimensional NMR, the backbone structure of this polymer was as expected and contained no byproducts formed by acid catalyzed addition across the fumarate double bond. Kinetic studies of the transesterification showed that the molecular weight reached a final Mn of 4900 (+/-700) and Mw of 9100 (+/-1300) after 16 h, while the polydispersity index remained below 1.8 throughout the reaction. Thus the PPF synthesized by the new method is of higher molecular weight and greater purity than our previously prepared material.

Acylation↗

PubMed1998

Osteoblastic phenotype of rat marrow stromal cells cultured in the presence of dexamethasone, beta-glycerolphosphate, and L-ascorbic acid.

We investigated the effects of the time course of addition of osteogenic supplements dexamethasone, beta-glycerolphosphate, and L-ascorbic acid to rat marrow stromal cells, and the exposure time on the proliferation and differentiation of the cells. It was the goal of these experiments to determine the time point for supplement addition to optimize marrow stromal cell proliferation and osteoblastic differentiation. To determine this, two studies were performed; one study was based on the age of the cells from harvest, and the other study was based on the duration of exposure to supplemented medium. Cells were seen to proliferate rapidly at early time points in the presence and absence of osteogenic supplements as determined by 3H-thymidine incorporation into the DNA of replicating cells. These results were supported by cell counts ascertained through total DNA analysis. Alkaline phosphatase (ALP) activity and osteocalcin production at 21 days were highest for both experimental designs when the cells were exposed to supplemented medium immediately upon harvest. The ALP levels at 21 days were six times greater for cells maintained in supplements throughout than for control cells cultured in the absence of supplements for both studies, reaching an absolute value of 75 x 10(-7) micromole/min/cell. Osteocalcin production reached 20 x 10(-6) ng/cell at 21 days in both studies for cells maintained in supplemented medium throughout the study, whereas the control cells produced an insignificant amount of osteocalcin. These results suggest that the addition of osteogenic supplements to marrow-derived cells early in the culture period did not inhibit proliferation and greatly enhanced the osteoblastic phenotype of cells in a rat model.

Alkaline Phosphatase↗

PubMed1998

In vivo degradation of a poly(propylene fumarate)/beta-tricalcium phosphate injectable composite scaffold.

This study was designed to investigate the in vivo biodegration and biocompatibility of a poly(propylene fumarate) (PPF)-based orthopedic biomaterial. The effects of varying the PPF to N-vinyl pyrrolidinone ratio and PPF to beta-tricalcium phosphate content were studied. The composite mechanical properties and local tissue interactions were analyzed over 12 weeks. An initial increase in both compressive modulus and strength was seen for composite formulations that incorporated beta-tricalcium phosphate. The samples incorporating a higher PPF to N-vinyl pyrrolidinone ratio reached a maximal compressive strength of 7.7 MPa and a maximal compressive modulus of 191.4 MPa at 3 weeks. The lower PPF to N-vinyl pyrrolidinone ratio samples gained a maximum compressive strength of 7.5 MPa initially and a compressive modulus of 134.0 MPa at 1 week. At 6 weeks, all samples for formulations incorporating beta-tricalcium phosphate crumbled upon removal and were not mechanically tested. Samples that did not incorporate beta-tricalcium phosphate were very weak and insufficient for bone replacement at the 4-day time point and beyond. Tissue interactions resulted in a mild inflammatory response at the initial time points and mature fibrous encapsulation by 12 weeks.

Animals↗

PubMed1998

In vitro and in vivo degradation of poly(propylene fumarate-co-ethylene glycol) hydrogels.

The degradation of poly(propylene fumarate-co-ethylene glycol) hydrogels was examined in vitro in phosphate-buffered saline at pH 7.4 and in vivo in a subcutaneous rat model. These hydrogels have potential application as biodegradable, injectable cardiovascular stents, and, as such, their mass loss, dimensional changes, mechanical properties, morphology, and biocompatibility over a 12-week time course were evaluated. Three formulations were fabricated: one base formulation consisting of 25% (w/w) PEG, molecular weight 4,600; one high weight percent PEG formulation with 50% (w/w) PEG; and one high molecular weight PEG formulation, molecular weight 10,500. All three formulations showed significant weight loss (between 40 and 60%) on the first day due to leaching of the uncrosslinked fraction. Further weight loss was observed only for the low weight percent PEG copolymers in the in vivo case, and a slight increase in volume was observed due to degradative swelling. The mechanical properties of the P(PF-co-EG) hydrogels decreased significantly in the first 3 weeks, showing the biphasic pattern typical of bulk degradation. In vitro, the hydrogels showed at least a 20% retention of their initial ultimate tensile stress after 3 weeks. The dynamic mechanical properties showed similar retention, with the in vivo mechanical properties differing from the in vitro properties only after 6 weeks of degradation. Differences in PEG molecular weight appeared to have little effect, but increasing the weight percent PEG decreased the rate of degradation both in vitro and in vivo. The morphology of the copolymer films, based on scanning electron microscopy observation, was not significantly different either among the three formulations or over the time course of the study, suggesting there were no macroscopic structural changes during this time period. The P(PF-co-EG) hydrogels demonstrated good initial biocompatibility, showing responses characteristic of biomaterial implants.

Animals↗

PubMed1998

Polymer concepts in tissue engineering.

Traumatic injuries, cancer treatment, and congenital abnormalities are often associated with abnormal bone shape or segmental bone loss. Restoration of normal structure and function in these cases requires replacement of the missing bone that may be accomplished by surgical transfer of natural tissue from an uninjured location elsewhere in the body. However, this procedure is limited by availability, adequate blood supply, and secondary deformities at the donor site. One strategy to overcome these problems is to develop living tissue substitutes based on synthetic biodegradable polymers. Three methods of bone regeneration using biodegradable polymers are being studied in our laboratory: tissue induction, cell transplantation, and fabrication of vascularized bone flaps. Injectable polymers are used for filling skeletal defects and guiding bone tissue growth. Their main advantage is minimizing the surgical intervention or the severity of the surgery. Polymer-cell constructs also hold great promise in the field of tissue engineering. They provide a scaffold on which cells grow and organize themselves. As the cells begin to secrete their own extracellular matrix, the polymer degrades and is eventually eliminated from the body, resulting in completely natural tissue replacement. Bone flaps can be fabricated ectopically into precise shapes and sizes. With an attached vascular supply, these flaps can be transferred into areas deficient in vascularity. This article discusses polymer concepts regarding bone tissue engineering and reviews recent advances of our laboratory on guided bone regeneration using biodegradable polymer scaffolds.

Animals↗

PubMed1997

Characterization of partially saturated poly(propylene fumarate) for orthopaedic application.

A partially saturated linear polyester based on poly(propylene fumarate) (PPF) was synthesized for potential application in filling skeletal defects. The synthesis was carried out according to a two-step reaction scheme. Propylene glycol and fumaryl chloride were first combined to form an intermediate fumaric diester. The intermediate was then subjected to a transesterification to form the PPF-based polymer. This method allowed for production of a polymer with a number average molecular weight up to 1500 and a polydispersity index of 2.8 and below. The polymeric backbone structure was investigated through the use of FTIR and NMR. Kinetic studies of the transesterification allowed mapping of the molecular weight increase with reaction time. The final product was also characterized by thermal and solubility analysis.

Bone Cements↗