Biomedical subjects

S Jeff Shepard

Publications and source records attributed to S Jeff Shepard.

3 recordsLinked to original sources

PubMed2005

Measurement of CT radiation profile width using CR imaging plates.

This paper describes the procedure for using a Fuji computed radiography (CR) imaging plate (IP) for the measurement of computed tomography (CT) radiation profiles. Two sources of saturation in the data from the IP, signal and quantization, were characterized to establish appropriate exposure and processing conditions for accurate measurements. The IP generated similar profiles compared to those obtained from digitized ready-pack films, except at the profile edges, where the exposure level is low. However, when IP pixel values are converted to exposure, CR and digitized film profiles are in agreement. The full width at half maximum (FWHM) of the CT radiation profile was determined from the relationship between pixel value and exposure and compared to FWHM of the digitized optical density profile from film. To estimate the effect of scattering by the cassette material, radiation profiles were acquired from IPs enclosed in a cassette or in a paper envelope. The presence of the cassette made no difference in the value determined for FWHM. With proper exposure and processing conditions, the FWHM of 5, 10, and 15 mm collimated beams were measured using IPs to be 7.1, 11.9, and 17.0 mm and using film to be 7.2, 12.2, and 16.8 mm, respectively. Our results suggest that, under appropriate conditions, the estimation of the width of the CT radiation profile using Fuji CR is comparable to the measurement from film density described in American Association of Physicists in Medicine (AAPM) Report No. 39. Although our experiment was conducted using Fuji CR, we anticipate that CR plates from other vendors could be successfully used to measure CT beam profiles because of similar empirical relationships between pixel value and exposure.

Radiation Dosage↗

PubMed2003

Measurement of focal spot size with slit camera using computed radiography and flat-panel based digital detectors.

The purpose of this study was to evaluate the use of digital x-ray imaging detectors for the measurement of diagnostic x-ray tube focal spot size using a slit camera. Slit camera images of two focal spots for a radiographic x-ray tube were acquired with direct-exposure film (DF) (as specified by the National Electrical Manufacturers Association [NEMA] Standards Publication No. XR 5, 1992), computed radiography (CR) imaging plates, and an a-Si:H/CsI:Tl-based flat-panel (FP) detector. Images obtained with the CR and the FP were acquired over a broad range of detector entrance exposure levels. The DF slit images were evaluated according to NEMA specifications (visually, using a 7x magnifying glass with reticule) by six medical physicists. Additionally, the DF images were digitized and the focal spot sizes obtained from the digital profiles of the slit. The CR and the FP images were analyzed in a manner similar to the digitized DF images. It took less than 20 minutes for a complete CR or FP measurement of focal spot size in two dimensions. In comparison, a typical DF measurement with visual evaluation takes at least 60 minutes, in our experience. In addition to a great reduction in measurement time achieved by using digital detectors, the tube loading requirements were reduced to approximately 20 mAs compared with approximately 1000 mAs when using the DF technique. The calculated focal spot sizes for CR and FP differed from those of digitized DF by -2.4% to +4.8% (sigma=2.5%), far less than the -16.6% to +9.3% (sigma=8.1%) variability introduced by the visual evaluation of the slit image. In addition, the calculated focal spot sizes for the CR and the FP images maintained a coefficient of variation <1.0% over the broad range of exposure levels. Based upon these results, we conclude that (1) FP and CR detectors yield consistent results in measurements of x-ray tube focal spot sizes, (2) compared to DF, CR and FP significantly reduce measurement time and tube loading requirements, (3) CR and FP readily permit digital profile analysis, thereby eliminating observer error, and (4) unlike DF, CR and FP are independent of exposure level.

Calibration↗

PubMed2002

Implementing the DICOM Grayscale Standard Display Function for mixed hard- and soft-copy operations.

The aim of this work was to implement the DICOM Grayscale Standard Display Function (GSDF) at all stages of image presentation for computed radiography (CR) and direct digital radiography (DR) modalities. Cathode-ray tubes (CRT) were calibrated according to vendor procedures. Printer look-up-tables (LUT) were measured. Custom LUTs were created and loaded. Fuji CR gradation processing parameters were adjusted to accommodate a GSDF printer LUT. Conformance to the GSDF for hard-copy and soft-copy displays was measured with DICOM Part 14 procedures. One system was intended to completely incorporate the GSDF, although the hard-copy result was correct. The CR systems required creation of custom GSDF printer LUTs, adjustment of gradation processing parameters, and/or calibration of CRT luminance response at the quality control station. The picture archiving and communication system workstations from one vendor required third-party software for calibration. Current implementations of DICOM GSDF by vendors may be inconsistent or nonexistent. Significant effort by in-house staff must be expended to properly incorporate the GSDF.

Data Display↗