PubMed Health⌕ Search

Biomedical subjects

S L Ong

Publications and source records attributed to S L Ong.

At least 19 recordsLinked to original sources
PubMed2006

Effects of solid retention time on the performance of submerged anoxic/oxic membrane bioreactor.

In this study, four similar bench-scale submerged Anoxic/Oxic Membrane Bioreactors (MBR) were used simultaneously to investigate the effects of solids retention time (SRT) on organic and nitrogen removal in MBR for treating domestic wastewater. COD removal efficiencies in all reactors were consistently above 94% under steady state conditions. Complete conversion of NH(4+)-N to NO(3-)-N was readily achieved over a feed NH(4+)-N concentration range of 30 to 50 mg/L. It was also observed that SRT did not significantly affect the nitrification in the MBR systems investigated. The average denitrification efficiencies for the 3, 5, 10 and 20 days SRT operations were 43.9, 32.6, 47.5 and 66.5%, respectively. In general, the average effluent nitrogen concentrations, which were mainly nitrate, were about 22.2, 27.6, 21.7 and 13.9 mg/L for the 3, 5, 10 and 20 days SRT systems, respectively. The rate of membrane fouling at 3 days SRT operation was more rapid than that observed at 5 days SRT. No fouling was noted in the 10 days and 20 days SRT systems during the entire period of study.

Bioreactors↗
PubMed2005

Biofiltration pretreatment for reverse osmosis (RO) membrane in a water reclamation system.

Biofouling control is considered as a major challenge in operating membrane systems. A lab-scale RO system was setup at a local water reclamation plant to study the feasibility of using biofiltration as a pretreatment process to control the biofouling. The biological activity in the RO system (feed, product, reject streams) was tested using the standard serial dilution plating technique. Operational parameters such as differential pressure (DP) and permeate flowrate of the system were also monitored. Effects of biofilter on AOC and DOC removals were investigated. Biofiltration was found to be a viable way of assimilable organic carbon (AOC) and dissolved organic carbon (DOC) removals, with removal efficiencies of 40-49% and 35-45% at an empty bed contact time (EBCT) of 30 min. It was also found that using the biofiltration as a pretreatment reduced the rate of biofouling. It took only about 72 h for biofouling to have a significant impact on the performance of the RO membrane, when the system was operated without using biofiltration as pretreatment. There was, however, a five times increase in operational length to more than 300 h when biofiltration was used. This study presented the suitability of the biofilter as an economical and simple way of biofouling control for RO membrane.

Biofilms↗
PubMed2005

Development of an integrated membrane process for water reclamation.

An integrated membrane process (IMP) comprising a membrane bioreactor (MBR) and a reverse osmosis (RO) process was developed for water reclamation. Wastewater was treated by an MBR operated at a sludge retention time (SRT) of 20 days and a hydraulic retention time (HRT) of 5.5 h. The IMP had an overall recovery efficiency of 80%. A unique feature of the IMP was the recycling of a fraction of RO concentrate back to the MBR. Experimental results revealed that a portion of the slow- and hard-to-degrade organic constituents in the recycle stream could be degraded by an acclimated biomass leading to an improved MBR treatment efficiency. Although recycling concentrated constituents could impose an inhibitory effect on the biomass and suppress their respiratory activities, results obtained suggested that operating MBR (in the novel IMP) at an F/M ratio below 0.03 g TOC/g VSS.day could yield an effluent quality comparable to that achievable without concentrate recycling. It is noted in this study that the novel IMP could achieve an average overall TOC removal efficiency of 88.940% and it consistently produced product water usable for high value reuse applications.

Biomass↗
PubMed2004

Biofilm morphology and nitrification activities: recovery of nitrifying biofilm particles covered with heterotrophic outgrowth.

Biofilm processes are commonly used for nitrification. Operationally, a whitish heterotrophic biofilm layer tends to develop onto nitrifying biofilm when it has been exposed to organic carbon-containing wastewater for a prolonged period. The development of a heterotrophic biofilm layer could lead to deterioration in nitrification activities and biofilm morphology. The recovery characteristics, in terms of biofilm morphology and nitrification activities, of deteriorated biofilm particles (i.e. nitrifying biofilm particles covered with heterotrophic outgrowth) were investigated by transferring the deteriorated biofilm particles (from an Ultra-Compact Biofilm Reactor (UCBR) which was part of a packed bed-UCBR system used for treating organic carbon and ammonia-containing wastewater) to a UCBR fed solely with ammonia wastewater (referred to as 'Recovery-UCBR'). At a hydraulic retention time (HRT) of 8.7 h and a sand-carrier concentration of 4.0% (v/v), density of the outer heterotrophic biofilm layer reduced progressively which led to subsequent detachment of this layer from the nitrifying biofilm particles. As a result, morphology of the nitrifying biofilm improved gradually in the Recovery-UCBR. A stable nitrification rate of up to 1.74 kg NH4+-N/m3 d was obtained in the Recovery-UCBR.

Ammonia↗
PubMed2004

Post-treatment of banknote printing works wastewater ultrafiltration concentrate.

A novel process of vortex settling and stage-2 ultrafiltration (UF) with alternating feed direction was used to further concentrate the concentrate produced by a stage-1 UF employed for treatment of banknote printing works wastewater. In this post-treatment process, the final concentrate volume for incineration was reduced by 4-5 times while the permeate of the stage-2 UF could be further reused in the banknote printing operation. It was noted vortex settling facilitated settling of the printing ink and the strategy of regularly alternating feed direction in the UF resulted in a higher permeate flux compared to the corresponding flux for operation without alternating feed direction. The hydraulic retention time (HRT) of the vortex settling tank (VST) used in the pilot-scale experiment was 14 min while feed direction to the stage-2 UF was alternated once every hour. Based on the pilot-scale experimental results, a full-scale system was set up. An economic analysis showed that the novel system was a cost-effective option for post-treatment of stage-1 UF concentrate. The treatment system has been successfully implemented at several Chinese banknote printing companies.

Coloring Agents↗
PubMed2004

In-situ characterization of microbial community in an A/O submerged membrane bioreactor with nitrogen removal.

The bacterial community involved in removing nitrogen from sewage and their preferred DO environment within an anoxic/oxic membrane bioreactor (A/O MBR) was investigated. A continuously operated laboratory-scale A/O MBR was maintained for 360 d. At a sludge age of 150 d and a C/N ratio of 3.5, the system was capable of removing 88% of the influent nitrogen from raw wastewater through typical nitrogen removal transformations (i.e. aerobic ammonia oxidation and anoxic nitrate reduction). Characterization of the A/O MBR bacterial community was carried out using fluorescence in situ hybridization (FISH) techniques. FISH results further showed that Nitrosospira spp. and Nitrospira spp. were the predominant groups of ammonia and nitrite oxidizing group, respectively. They constituted up to 11% and 6% of eubacteria at DO below 0.05 mg/l (low DO), respectively, and about 14% and 9% of eubacteria at DO between 2-5 mg/l (sufficient DO), respectively, indicating preference of nitrifiers for a higher DO environment. Generally low counts of the genus Paracoccus were detected while negative results were observed for Paracoccus denitrificans, Alcaligenes spp, and Pseudomonas stutzeri under the low and sufficient DO environments. The overall results indicate that Nitrosospira spp., Nitrospira spp. and members of Paracoccus spp. can be metabolically functional in nitrogen removal in the laboratory-scale A/O MBR system.

Alcaligenes↗
PubMed2004

Two-stage SBR for treatment of oil refinery wastewater.

A two-stage sequencing batch reactor (SBR) system was used for treatment of oily wastewater with COD and oil and grease (O&G) concentrations ranging from 1,722-7,826 mg/L and 5,365-13,350 mg/L, respectively. A suitable start-up protocol was developed using gradual increase in oily wastewater composition with methanol as the co-substrate. This strategy enabled a short acclimation period of 12 days for the sludge in the two-stage SBR to adapt to the oily wastewater. After acclimation, the 1st stage and 2nd stage SBRs were able to achieve COD removals of 47.0+/-2.4% and 95.3+/-0.5%, respectively. The 1st stage SBR was able to achieve 99.8+/-0.1% of O&G removal and effluent O&G from the 1st stage SBR was only 6+/-2 mg/L. The 2nd stage SBR was used to further remove COD in the effluent from the 1st stage SBR. The final effluent from the 2nd stage SBR had a COD concentration of 97+/-16 mg/L with no detectable O&G content. Thus, a two-stage SBR system was shown to be feasible for treating high strength oily wastewater to meet the local discharge standards.

Bioreactors↗
PubMed2003

Effects of pH and temperature on the survival of coliphages MS2 and Qbeta.

The RNA F-specific coliphages, MS2 and Qbeta, have been used as virus indicators in water and wastewater studies. It is therefore useful to have a good understanding concerning the effects of environmental factors on their survival in order to choose an appropriate candidate for assessing microbial safety in relation to water quality management. The effects of pH and temperature on the survival of these two coliphages were investigated. MS2 survived better in acidic conditions than in an alkaline environment. In contrast, Qbeta had a better survival rate in alkaline conditions than in an acidic environment. The inactivation rates of both coliphages were lowest within the pH range 6-8 and the temperature range 5-35 degrees C. The inactivation rates of both coliphages increased when the pH was decreased to below 6 or increased to above 8. The inactivation rates of both coliphages increased with increasing temperature. Qbeta behaved peculiarly in extreme pH buffers, i.e. it was inactivated very rapidly initially when subjected to an extreme pH environment, although the inactivation rate subsequently decreased. In general, MS2 was a better indicator than Qbeta. However, within the pH range 6-9 and at temperatures not above 25 degrees C, either MS2 or Qbeta could be used as a viral indicator.

Environment↗
PubMed2003

Community structure of microbial biofilms associated with membrane-based water purification processes as revealed using a polyphasic approach.

The microbial communities of membrane biofilms occurring in two full-scale water purification processes employing microfiltration (MF) and reverse osmosis (RO) membranes were characterized using a polyphasic approach that employed bacterial cultivation, 16S rDNA clone library and fluorescence in situ hybridization techniques. All methods showed that the alpha-Proteobacteria was the largest microbial fraction in the samples, followed by the gamma-Proteobacteria. This suggested that members of these two groups could be responsible for the biofouling on the membranes studied. Furthermore, the microbial community structures between the MF and RO samples were considerably different in composition of the most predominant 16S rDNA clones and bacterial isolates from the alpha-Proteobacteria and only shared two common groups ( Bradyrhizobium, Bosea) out of more than 17 different bacterial groups observed. The MF and RO samples further contained Planctomycetes and Fibroacter/ Acidobacteria as the second predominant bacterial clones, respectively, and differed in minor bacterial clones and isolates. The community structure differences were mainly attributed to differences in feed water, process configurations and operating environments, such as the pressure and hydrodynamic conditions present in the water purification systems.

Alphaproteobacteria↗
PubMed2003

Treatability of organic fractions derived from secondary effluent by reverse osmosis membrane.

Dissolved organic matters (DOMs) from two batches of secondary effluent collected from a local water reclamation plant were fractionated using column chromatographic method with non-ionic resins XAD-8, AG MP-50 and IRA-96. Seven isolated fractions were obtained from the fractionation study and these fractions were quantified using DOC, UV(254) and SUVA values. The fractionation study revealed that the secondary effluent samples comprised about 47.3-60.6% of hydrophobic and 39.4-52.7% of hydrophilic solutes. The treatability of each isolated fraction was investigated by subjecting each fraction to reverse osmosis (RO) treatment individually. It was noted that RO process could achieve high DOC rejections for acid and neutral fractions (ranging from 80% to 98% removal) probably due to the negative charge of RO membrane. The results obtained also indicated that hydrophobicity of DOMs is significant in determining treatability of organic species by RO process. The performance of RO in terms of DOC rejection of un-fractionated secondary effluent was also investigated to assess possible effects of interactions among organic fractions on their treatability by RO process. It was noted that DOC rejection associated with the un-fractionated secondary effluent was generally higher (ranging from 2% to 45%) than the corresponding rejection obtained from each individual fraction isolated from the secondary effluent. This finding suggested there is a beneficial interaction among the fractions that in turn has contributed towards a better overall DOC rejection performance by RO treatment.

Chromatography↗
PubMed2003

A new method for characterizing denitrifying phosphorus removal bacteria by using three different types of electron acceptors.

This study investigated the characteristics of denitrifying phosphorus removal bacteria by using three different types of electron acceptors as well as the positive role of nitrite in phosphorus removal process. Denitrifying phosphorous removal bacteria was enriched under anaerobic-anoxic (A/A) condition. To understand A/A sludge better, sludge from two other sources were also studied. These include sludges obtained from a lab-scale anaerobic-anoxic-aerobic (A/A/O) system and a local sewage treatment plant. Three types of possible electron acceptors (oxygen, nitrate and nitrite) were examined for their roles in phosphorus uptake. The results obtained indicated that oxygen, nitrate and nitrite were able to act as electron acceptors successfully. This observation suggested that in addition to the two well-accepted groups of phosphorus removal bacteria (one can only utilize oxygen to take up phosphorus, P(O), while the other can use both oxygen and nitrate, P(ON)), a new group of phosphorus removal bacteria, P(ON(n)), which could use oxygen, nitrate or nitrite to take up phosphorus was identified. The relative population of these three types of bacteria could be calculated from results obtainable from phosphorus uptake batch experiments with either oxygen or nitrate or nitrite as electron acceptor. The results obtained in this study showed that A/A sludge had similar phosphorus removal performance as the A/A/O sludge. However, it has better denitrifying phosphorus removal capability, which was demonstrated by the relative population of the three groups of bacteria. The results also suggested that nitrite was not an inhibitor to phosphorus removal process. Instead, it is an alternative electron acceptor to oxygen or nitrate.

Bacteria↗
PubMed2003

Kinetics of beta-mannanase fermentation by Bacillus licheniformis.

Bacterial growth, konjac powder utilization and beta-mannanase production by Bacillus licheniformis NK-27 in batch fermentation were used to develop a model of the process. The optimal set of parameters was estimated by fitting the model to experimental data. The results predicted by the model were in good agreement with the experimental data. NOMENCLATURE: fs, fraction parameter; Kp, constant in Equation (6) (g l(-1)); Ks, Monod constant for bacteria growth (g l(-1)); m, maintenance coefficient (g g(-1) h(-1)); P, beta-mannanase concentration (g 1(-1)); qm, constant in Equation (6) (h(-1)); S, substrate concentration (g l(-1)); S0, initial substrate concentration (g l(-1)); Si, insoluble substrate concentration (g l(-1)); Ss, soluble substrate concentration (g l(-1)); t, fermentation time (h); tL, lag time (h); mu, specific growth rate (h(-1)); mu(max), maximum specific growth rate (h(-1)); X, biomass concentration (g l(-1)); YP/S, beta-mannanase yield on carbon substrate (g g(-1)); YX/S, biomass yield on carbon substrate (g g(-1)).

Bacillus↗
PubMed2003

Identification and quantification of bisphenol A by gas chromatography and mass spectrometry in a lab-scale dual membrane system.

Endocrine disruptor contamination is an emerging issue of concern in the field of water quality engineering. In this study, a lab-scale microfiltration (MF) and reverse osmosis (RO) based water reclamation system was set up to monitor and evaluate the removal of bisphenol A (BPA), which is a known oestrogenic compound. The identification and quantification of BPA were performed by using gas chromatography coupled with mass spectrometry. It was noted that the detection method used in this study was able to achieve an average recovery ranging from 88.2 to 94.1% of BPA with standard deviations of less than 10% in different spiked samples. The detection limit of the analytical protocol was determined at 20 ng L(-1). Based on the analytical protocol, it was noted that a low level of BPA (1.18-3.04 microg L(-1)) could be detected in feed water (effluent of an activated sludge treatment system) to the dual membrane water reclamation system. The results obtained suggested that BPA could be easily chlorinated by sodium hypochlorite with a dosage of 4 to 5 mg L(-1) and a contact time of 1 to 2 min. In this lab-scale study, a satisfactory removal of BPA was readily obtained by RO and BPA was abated to an undetectable level in the product water. It was noted that the RO rejection characteristic of BPA was not sensitive to the variations in raw feed water characteristics experienced in this study. In addition, it was noted that BPA concentration present in raw feed water did not exert any significant impact on RO performance in terms of BPA rejection. The results of this study demonstrated that membrane technology could be effectively used for BPA removal.

Benzhydryl Compounds↗
PubMed2003

Removal of MS2 bacteriophage using membrane technologies.

Removals of MS2 bacteriophage virus using different membrane materials under different operating pressures were investigated. The results obtained in this study suggested that a better log removal in terms of MS2 bacteriophage virus could be achieved using Polyamide RO membrane under the optimum operating pressure of 100 psi. It is further noted that variable MS2 influent concentration levels resulted in corresponding variable log removals of the bacteriophages by the Polyamide RO membrane. The presence of MS2 bacteriophage virus in the effluent could possibly be due to leakage of bacteriophages through the membranes structure. Investigations using SEM and AFM showed that there were gaps or pores present in the membrane structure which were sufficiently large for the MS2 viruses to pass through.

Bacteria, Anaerobic↗
PubMed2002

Investigation of assimilable organic carbon (AOC) and bacterial regrowth in drinking water distribution system.

This paper investigated the variation of assimilable organic carbon (AOC) concentrations in water from several typical water treatment plants and distribution systems in a northern city of China. It is concluded from this study that: (1) The AOC in most of the product water of the studied water treatment plants and the water from the associated distribution systems could not meet the biostability criteria of 50-100 microg/L. (2) Only 4% of the measured AOC concentrations were less than 100 microg/L. However, about half of the measured AOC values were less than 200 microg/L. (3) Better source water quality resulted in lower AOC concentrations. (4) The variation of AOC concentrations in distribution systems was affected by chlorine oxidation and bacterial activity: the former resulted in an increase of AOC value while the latter led to a reduction in AOC. (5) The variation of AOC concentration followed different patterns in different distribution systems or different seasons due to their respective operational characteristics. (6) Less than 30% of AOC could be removed by a conventional treatment process, whereas 30-60% with a maximum of 50-60% could be removed by granular activated carbon (GAC). (7) The observation via scanning electron microscope (SEM) on distribution pipe tubercle samples demonstrated that the pipe inner wall was not smooth and bacteria multiplied in the crevice as well as in the interior wall of distribution pipes.

Bacteria↗
PubMed2002

An investigation on biological stability of product water generated by lab-scale and pilot-scale distillation systems.

Lab-scale and pilot-scale distillation systems were assessed in this study and the effectiveness of the treatment processes on Assimilable Organic Carbon (AOC) removal was also investigated. Seawater as one of the alternative water sources was used as the feed water and the resulting product water was intended for industry use. Acidification, ion trapping and anti-scaling chemical dosing were adopted as the pre-treatment processes to the feed water before distillation for pilot-plant system. The AOC assay was used to evaluate the efficiencies of various unit processes for AOC removal. Heterotrophic Plate Counts (HPC) was adopted in conjunction with AOC to determine the biological stability of the water samples. It is noted that the distillation system was able to produce a product water with an acceptable AOC concentration of less than 20 micrograms acetate-C L-1. This would suggest that the distillation system was capable of delivering a biologically stable product water. The results from lab-scale system indicated that pretreatment such as acidification, chlorination and antiscalant would increase AOC, although this does not affect the general performance of distillation system.

Carbon↗
PubMed2002

Packed bed columns for high rate nitrogen and carbon removals.

Two packed bed column (PB) systems, namely anoxic-anoxic and anoxic-oxic were investigated for treatment of wastewater containing high concentrations of nitrogen (N) and COD. The anoxic-anoxic PB removal rates 6.70 kg N/m3 x d and 26.02 kg COD/m3 x d, respectively. The responding removal rates of the anoxic-oxic PB system were 7.41 kg N/m3 and 28.00 kg COD/m3 x d, respectively. The N and COD removal efficiencies of anoxic anoxic PB system were in the range of 99.2-100% and 97.2-98.8%, respectively. The corresponding removal efficiencies of anoxic-oxic PB system were 97.5-100% and 98.6-99.4%, respectively. These findings showed that a PB system consisting of anoxic-oxic columns in series has a high capacity to remove nitrogenous and carbonaceous compounds even though the influent to the anoxic stage was oxygenated. Better system stability in terms of denitrification was, however, obtained with the anoxic-anoxic system.

Bioreactors↗