PubMed Health⌕ Search

Biomedical subjects

S L Trokel

Publications and source records attributed to S L Trokel.

At least 37 records · Page 2Linked to original sources

Laser radiation at various wavelengths for decompression of intervertebral disk. Experimental observations on human autopsy specimens.

The interaction of laser radiation with the nucleus pulposus from autopsy specimens of human intervertebral disks was evaluated at different wavelengths (193 nm, 488 nm & 514 nm, 1064 nm, 1318 nm, 2150 nm, 2940 nm, and 10600 nm). A significant correlation of linear least squares fit of the mass ablated as a function of incident energy was found for all lasers used except the Excimer at 193 nm. The 2940-nm Erbium:YAG laser was most efficient in terms of mass of disk ablated per joule in the limited lower range where this wavelength was observed. At higher energy levels, the CO2 laser in the pulsed mode was most efficient. However, the Nd:YAG 1064-nm and 1318-nm lasers are currently best suited for percutaneous laser disk decompression because of the availability of usable waveguides. Carbonization of tissue with the more penetrating Nd:YAG 1064-nm laser increases the efficiency of tissue ablation and makes it comparable to the Nd:YAG 1318-nm laser.

Autopsy↗

Effects of a 2.15-micron laser on human atherosclerotic xenografts in vivo.

The thulium-holmium-chromium:yttrium-aluminum-garnet (THC:YAG) laser has a tissue effect similar to that of the CO2 laser, with the advantage of transmissibility through flexible fibers. The authors used a human-rabbit xenograft model to evaluate the thrombotic and healing responses of atherosclerotic vessels subjected to laser energy. Occluded atherosclerotic human coronary artery segments were recanalized in vitro by use of the THC:YAG laser. Destruction of plaque by the laser was achieved with minimal collateral thermal damage. These vascular segments were then transplanted into the rabbit abdominal aorta. The authors observed that the luminal surface of the lased vessels was more thrombogenic than that of the nonlased control vessels. However, occlusion of the lased vessels did not occur. Repair of laser-treated tissue progressed until a mature, nonthrombogenic fibrin-platelet aggregate was adherent to the luminal wall. Overall, the lased vessels behaved in a fashion similar to the nonlased control vessels. On the basis of these results, the authors believe that the THC:YAG laser may have use in human angioplasty.

Angioplasty, Laser↗

Corneal healing following laser refractive keratectomy.

A 193-nm excimer laser system was used to ablate 4.5-mm optically contoured zones in the corneal stroma of rabbits to achieve optical flattening of 2, 4, 8, and 16 diopters. We studied the effect of edge profile and wound depth on reepithelialization and stromal remodeling using dichlorotriazinyl aminofluorescein, a vital dye that covalently binds to the stromal bed and delineates the boundaries of new collagen synthesis. All the corneas reepithelialized; no subsequent recurrent erosions occurred. All seven corneas that received an ablation of less than 50 microns were clear centrally at 8 weeks. At an ablation depth of approximately 100 microns, opacification and scarring were observed biomicroscopically and histopathologically in two specimens. No evidence of new collagen formation or epithelial hyperplasia was found in any of the seven corneas that remained clear. Stromal remodeling was observed in the two corneas that exhibited scarring.

Animals↗

Welding of gallbladder tissue with a pulsed 2.15 microns thulium-holmium-chromium:YAG laser.

Percutaneous endoscopic approaches to cholelithiasis would be facilitated by methods for welding gallbladder tissues. We evaluated the bursting pressure and histologic appearance of canine gallbladder tissue welded with a thulium-holmium-chromium:YAG (THC:YAG) laser producing a 2.15 microns pulsed output. The tissue absorption characteristics at this wavelength as well as the pulsed nature of the output permit tissue welding with limited collateral thermal damage. The THC:YAG is compatible with a flexible fiberoptic delivery system. Bursting strengths of the welded junctions averaged 42 mm Hg, which is above physiologically encountered pressures. Histologic sections of the bonded tissues revealed tissue fusion and limited thermal injury to the surrounding tissue. We feel that THC:YAG laser welding may be a useful technique in the clinical development of percutaneous endoscopic biliary surgery.

Animals↗

In vitro comparison of thulium-holmium-chromium: YAG and argon ion lasers for welding of biliary tissue.

Laser welding offers several potential advantages over suture closure, including improved healing, lack of a nidus for stone formation, and greater speed and ease. We examined in vitro gallbladder cystic duct welds created by two different systems, the thulmium-holmium-chromium (THC):YAG (2,150 nm) and argon ion (488-514 nm) lasers, in an effort to define suitable parameters for tissue fusion. Mean bursting pressures for argon welds were 95 mm Hg at 1.5 W CW and 26 mm Hg at 1.5 W, 50 msec chopped delivery. For the THC:YAG laser, the mean bursting pressure for welds created with 300 mJ pulses was 45 mm Hg. Full-thickness tissue fusion and limited collateral thermal damage were observed histologically for both the CW argon and pulsed THC:YAG welds. Examination of the suggested mechanisms of tissue fusion for these photothermal lasers suggests that increased duration of tissue heating at the appropriate temperature results in more extensive collagen crosslinking and a stronger weld.

Animals↗

Sutureless microvascular anastomosis using the THC:YAG laser: a preliminary report.

Laser anastomosis of the rat carotid artery was performed using a new mid-infrared laser, the pulsed thulium-holmium-chromium: YAG (THC:YAG) laser (2.15 microns). Solid silicone stents made stay sutures unnecessary for coaptation of vessel edges during laser bonding. Grossly, the laser anastomoses displayed minimal thermal distortion of the vessel contour and no tissue carbonization. Of the 30 anastomoses performed, 27 were patent and 3 had separation of the weld shortly after the approximator clamp was released. Mean anastomotic time was 4 min 48 sec. Mean bursting pressure for the 9 vessels tested was 400 mm Hg. Thrombosis did not occur at any time during our examination of these anastomoses. Fusion of collagen fibers in the media was confirmed histologically. Unlike the CO2 laser, the THC:YAG is transmissible through flexible silica fibers, which greatly facilitates delivery of the laser in a microsurgical operative field. The THC:YAG provides shallower absorption depth than Nd:YAG and argon lasers but somewhat deeper tissue penetration than CO2. For microvessels, this intermediate absorption results in full-thickness fusion of the media, with minimal thermal damage to vascular tissue adjacent to the anastomosis.

Anastomosis, Surgical↗

A fiberoptic compatible midinfrared laser with CO2 laser-like effect: application to atherosclerosis.

In theory, pulses of laser light in the 2-microns range should ablate tissue in a manner similar to that of the 10.6-microns CO2 laser with the added advantage of efficient transmission through flexible quartz fibers. Using 200-microseconds pulses of 2.15-microns thulium-holmium-chromium:YAG (THC:YAG) laser light, we were able to create 700-microns-diameter holes through calcific atherosclerosis in vitro. In vivo evaluation of thrombogenicity and healing was accomplished by exposing the luminal surface of rabbit aortas to the THC:YAG laser. Serial histologic examinations of laser-treated rabbit aortae revealed a time course of resolution of the lesions which was very similar to that observed with like-sized lesions created with the same amount of continuous wave CO2 energy. No significant differences in thrombogenicity nor healing response were noted. The excellent in vivo response observed is due in part to the pulsed nature of the THC:YAG laser output as well as to the efficient tissue absorption at the 2.15-microns wavelength. We feel that excellent ablative effects with minimal collateral thermal damage can be obtained through fiberoptic delivery systems by taking advantage of laser wavelengths corresponding to the infrared absorption peak of water in the 2-microns region and pulsed delivery of the laser energy.

Animals↗

Mid-infrared lasers for endoscopic surgery. A new class of surgical lasers.

Unlike the Nd:YAG, the CO2 laser produces well circumscribed tissue removal with little unwanted damage because of its high absorption coefficient relative to tissue water. Unfortunately, conventional quartz fibers cannot transmit wavelengths greater than three microns, well below the ten micron wavelength of the CO2 laser. Thus, fiberoptic transmission of CO2 laser requires use of exotic materials that lack the excellent properties of quartz fibers and that, in some cases, are toxic or chemically unstable. However, there are large peaks in the infrared absorption curve of water in the two to three micron region. Lasers that operate in this mid-infrared region should permit CO2-like precision of cutting, along with excellent transmission through quartz fiberoptics. Two mid-infrared lasers with a fiberoptic delivery system, the Er:YAG (2.94 micron) and the Tm-Ho-Cr:YAG (2.15 micron) have been evaluated with human colon tissue in vitro and with rabbit gastric tissue in vivo. Histologic sections reveal excellently well localized lesions with minimal underlying thermal damage. Depth of penetration is controllable and occurs in very small increments. There is little spreading of the lesions at the 24 hour mark resulting from secondary thermal damage. Based on these facts, the authors think that these lasers will be of benefit to endoscopic surgeons.

Animals↗

Preliminary evaluation of a pulsed 2.15-micron laser system for fiberoptic endoscopic surgery.

There is a need for lasers that are compatible with fiberoptic endoscopes and that provide greater cutting precision than currently can be produced by the widely used Nd:YAG (1.06 micron) laser. Recently available lasers that operate in the 2-micron region fill this need. This laser light energy can be transmitted by low OH- silica fibers and has much less tissue penetration than radiation at 1.06 micron. We have been evaluating a prototype solid state laser system that produces pulses of 2.15 microns light that is delivered by a silica based fiberoptic delivery system with negligible transmission losses. This system is based on a thulium-holmium-chromium doped YAG (Tm-Ho-Cr: YAG) rod that lases at 2.15 micron. The laser does not require cryogenic cooling, toxic gases, or custom utilities and should be practical in a clinical environment. In vivo animal testing of this laser confirms that it provides greater ablating precision than does the Nd:YAG laser at 1.06 micron.

Animals↗

Long-term healing of the central cornea after photorefractive keratectomy using an excimer laser.

Using an excimer laser at 193 nm, 3-mm diameter discs were ablated from the optical zone of monkey corneas at a variety of depths up to 130 micron. Tissue was examined by light and electron microscopy 4 and 5 weeks and 6 and 8 months postoperatively. With the exception of the deepest ablation, all corneas were clear immediately postoperatively. At 1 month, ablations of 40 micron remained clear, whereas all others showed some degree of haze. By 3 months, discs at 60 micron depth were clear, and there was less haze in others. Haze was progressively lost over 6 months, but in the deepest discs it could still be discerned on slit-lamp examination. Microscopic observation showed that reepithelialization had occurred within 24 to 48 hours. Over subsequent months, a normal morphology was maintained in this layer with the exception that basal cells were slightly more elevated particularly at the disc margins where the epithelium contained more cell layers. Stromal reorganization was accompanied by an initial phase of vacuolation and invasion by keratocytes, but by 6 months postoperatively almost all vacuolation had disappeared and keratocyte numbers had almost returned to normal. By 8 months, the morphology was near normal with the exception that Bowman's membrane was absent and there was still a degree of disorder in the immediate subepithelial stromal fibers. The basement membrane of epithelial cells was reestablished but slightly more undulant than in nonirradiated areas. This undulation was retained in the 8-month postoperative specimens and at this time a normal thickness of 60 nm was displayed.

Animals↗

Ultrastructural comparison of conventional surgical and argon fluoride excimer laser keratectomy.

We used scanning electron microscopy to examine the structure of the surfaces created during keratectomy procedures carried out by conventional surgery and ablation by an excimer laser. The walls and the floor of the surgical site were rough with undulations greater than 10 micron in size, caused by broken lamellae and ruptured cells. In contrast, the surfaces produced by the excimer laser were smooth with perturbations of 1 micron or less and were sealed with a pseudomembrane. This smooth, sealed surface produced by the laser is probably responsible for the transparency of the healed cornea in contrast to the scarring produced when a conventional surgical keratotomy heals.

Argon↗

Excimer laser therapy for experimental Candida keratitis.

In vivo treatment of experimental Candida albicans keratitis with the excimer laser achieved sterilization on culture and histopathologically in all corneas in which clinically visible infiltration was removed with the laser at the 193-nm wavelength. Treatment at the 248-nm wavelength was not successful in eradicating infection compared with untreated controls. The 193-nm wavelength is highly effective, probably because infected tissue is totally removed by ablative photodecomposition. At the 248-nm wavelength, thermal effects become more dominant and, therefore, fungal elements are incompletely ablated. Light microscopy two days after treatment at the 193-nm wavelength showed healing of ulcerated areas, fine basophilic stippling at the epithelial-stromal interface, and undamaged underlying stroma.

Animals↗

The role of the vitreous in the intraocular pressure rise after neodymium-YAG laser capsulotomy.

Autologous liquid vitreous injected into the anterior chamber of the phakic owl monkey eye leads to markedly increased intraocular pressure (IOP) peaking at one to two hours. In contrast, neodymium-YAG laser shock waves focused in the center of the anterior chamber of the same animal led to a mild decrease in IOP. Debris produced by laser pulses focused on the residual cortex of owl monkey eyes that had undergone extracapsular surgery failed to increase the IOP. Similarly, injection of dialyzed vitreous did not have any significant influence on IOP. We conclude that the disruption of the integrity of the anterior cortical gel and the subsequent release of a dialyzable intravitreal substance with a molecular weight of less than 10,000 daltons into the anterior chamber may contribute to the IOP rise after surgical discission, including neodymium-YAG laser posterior capsulotomy.

Animals↗

Quantitation of corneal ablation by ultraviolet laser light.

A surgical role has been suggested for the excimer laser. This followed the discovery of precision etching of biological materials by the laser's ultraviolet emissions. In studying the amount of tissue removed as the laser energy density (irradiance) was varied, we found significant differences for the 193-, 249-, and 308-nm laser emission lines. The most efficient cutting irradiance for each pulse appeared to be about 200 millijoules/sq cm for 193 nm, 1,000 millijoules/sq cm for 249 nm, and 1,500 millijoules/sq cm for 308 nm. The flat slope of the etch depth curve for 193 nm suggests it will be a stable frequency when used clinically.

Animals↗

Excimer laser radial keratotomy.

The central corneal flattening obtained by radial diamond knife incisions has been duplicated by radial laser incisions in 18 enucleated human eyes. The incisions, made by 193 nm far-ultraviolet light radiation emitted by the excimer laser, produced corneal flattening ranging from 0.12 to 5.35 diopters. Both the depth of the corneal incisions and the degree of central corneal flattening correlated with the laser energy applied. Histopathology revealed the remarkably smooth edges of the laser incisions.

Cornea↗

Posterior capsule opacification: experimental analyses.

The lenses of New Zealand White and Flemish Giant rabbits were removed using five techniques representative of the different clinical approaches to extracapsular cataract extraction currently employed. Posterior capsule opacification developed in all experimental animals within 6 weeks of the operation. None of the techniques reduced the incidence of the capsular opacification. Histological analyses including immunofluorescent and tritiated thymidine labelling were used to determine the nature of the cellular constitutents of the secondary membrane. The evidence indicates that the opacity is due not only to lens cells remaining after the operation but also consists of cells of nonlenticular origin. The data strongly implicate the anterior uvea as the source of those cells. Furthermore, the findings suggest that posterior capsule opacification is the product of a migration and a proliferation of both cell populations.

Animals↗

Interaction of ultraviolet laser light with the cornea.

The effect of pulsed ultraviolet (UV) laser light on the cornea depends on wavelength (photon energy), irradiance (photon flux), and pulse firing rate. At the available excimer laser wavelengths of 193, 249, 308, and 351 nanometers, the authors have varied the irradiance per pulse (10 to 2000 mj/cm2) as well a pulse frequency (1, 10, 25 Hz) and determined the thresholds for coagulation and ablation of the corneal stroma. The latter ablative action creates a groove resembling an incision and was present at all wavelengths studied. The threshold for ablation increased for longer wavelengths and lower pulse frequencies, except for 193-nm exposure, which was characterized by a constant threshold independent of laser pulse rate. The grooves at 193 nm were both biomicroscopically and histologically smooth and no coagulation effects were noted. Some degree of coagulation of adjacent tissues was noted at 249, 308, and 351 nm.

Animals↗

Measurement of spatial stability of spark position in burst-mode breakdown with the Nd:YAG laser.

Measurements to determine the precise position of the spark produced by optical breakdown in ocular media with a repetitive sequence of pulses from a Nd:YAG laser have been made. The results show that the location of the spark along the beam axis remains fixed within +/- 10 micrometers (the resolution of the experiment) for pulses with a time separation of 20 milliseconds, indicating that the surgical effects of a sequence of pulses can be cumulative.

Lasers↗