PubMed Health⌕ Search

Biomedical subjects

S Sadhra

Publications and source records attributed to S Sadhra.

16 recordsLinked to original sources
PubMed2006

Polycyclic aromatic hydrocarbon emissions from clinical waste incineration.

Since the introduction of the Environmental Protection Act in the UK, there are few reports of PAH emissions from clinical waste incinerators (CWIs) operating to improved performance standards. The main aim of this study is to determine PAH emissions from a state-of-the-art CWI focusing on the effects of reactive gases and operating variables on emissions. This was carried out by collection of stack samples over three phases of operation. At stack conditions, most PAHs are predicted to be in the vapour phase. Reactive losses of PAHs were closely correlated by rank with expected reactivities from laboratory studies. Estimates of emissions incorporating sampling losses were derived, although no correlation was found between PAH losses and the modest levels of reactive stack gases. PAH concentrations were one to two orders of magnitude lower than earlier reports from incinerators without effective air pollution control equipment (APCE). The low levels of carbon monoxide recorded were not correlated with any PAHs. This study demonstrates the impact of efficient combustion conditions and APCE on PAH emissions from a CWI.

Air Pollutants↗
PubMed2004

Occupational exposure to diesel exhaust fumes.

There is currently no OEL for diesel fumes in the UK. This study reports parallel measurements of airborne levels of diesel fume pollutants in nine distribution depots where diesel powered fork-lift trucks (FLTs) were in use. Correlations between individual pollutants are assessed as well as their spatial distribution. Samples were collected on board FLTs and at background positions at nine distribution depots. Substances measured and the range of exposures by site were: respirable dust (n = 76) GM </= 80-179 micro g/m(3); elemental carbon (n = 79) GM = 7-55 micro g/m(3); organic carbon (n = 79) GM = 11-69 micro g/m(3); ultrafine particles (n = 17) range = 58-231 x 10(3) particles/cm(3); selected particulate phase polycyclic aromatic hydrocarbons (PAHs) (n = 14) range = 6-37 ng/m(3). In addition, a tracer method based on ultrafine particle measurements was used to estimate the spatial distribution of total carbon and PAHs at the sites monitored. The spatial distribution was found to be reasonably uniform. Major diesel fume aerosol components were, in general, well correlated (r = 0.62-0.97). CO(2) measurements were also made and found to be below the HSE guideline of 1000 p.p.m., with most levels below 600 p.p.m.

Air Pollutants, Occupational↗
PubMed2004

Polycyclic aromatic hydrocarbons in solid residues from waste incineration.

Polycyclic aromatic hydrocarbons (PAH) levels in solid residues from clinical waste incineration were measured using HPLC with fluorescence detection. PAH mass emission rates and emission rates as a function of waste burned are also reported. For bottom ash, PAH levels and physical properties were found to be quite consistent. Levels of high molecular mass PAHs were comparable to levels previously reported in the literature when adjusted for differences in sample preparation techniques. However, levels of low molecular mass PAHs were considerably elevated in this study. Possible reasons for this finding include the composition of the waste, combustion conditions and methods of sample preparation. In contrast, no PAHs were found in fly ash, an unexpected finding which is probably attributable to matrix effects resulting from a surfeit of lime in the fly ash. Factors effecting the partitioning of PAHs and their environmental fate are also discussed.

Chromatography, High Pressure Liquid↗
PubMed2002

Workers' understanding of chemical risks: electroplating case study.

BACKGROUND: There is limited research concerning how small companies in particular, respond to health and safety messages. AIMS: To understand individuals' knowledge and beliefs about chemical risks and to compare these with those of experts. METHODS: The use of chromic acid in particular, and also other chemicals associated with chrome plating were studied. All chromium plating firms were based in the West Midlands. The methodology involved initial face to face interviews (n = 21) with chromium platers, structured questionnaires (n = 84) to test the prevalence of beliefs identified in the interviews, an expert questionnaire, and a workshop to discuss findings. The responses of platers were compared with those of occupational health and safety experts. RESULTS: Although chromium platers appeared to understand the short term adverse effects of the chemicals to which they are exposed, their understanding of long term, or chronic effects appeared to be incomplete. They had good knowledge of acute effects based primarily on experience. Platers were aware of the hazardous nature of the chemicals with which they work, but did not draw distinction between the terms "hazards" and "risks". They had difficulties articulating the effects of the chemicals and how exposure might occur; although it is inappropriate to equate this with lack of knowledge. A significant minority of platers displayed deficiencies in understanding key technical terms used in Safety Data Sheets. CONCLUSIONS: This study provides a method which can be used to gain some understanding of workers' knowledge and beliefs about risks that they are exposed to in the workplace. The study also identifies gaps between the platers' knowledge and beliefs and those of experts. New risk information needs to be designed which addresses the information needs of platers using language that they understand.

Acute Disease↗
PubMed2002

Occupational asthma caused by chloramines in indoor swimming-pool air.

The first series of three workers who developed occupational asthma following exposure to airborne chloramines in indoor chlorinated swimming pools is reported. Health problems of swimmers in indoor pools have traditionally been attributed to the chlorine in the water. Chlorine reacts with bodily proteins to form chloramines; the most volatile and prevalent in the air above swimming pools is nitrogen trichloride. Two lifeguards and one swimming teacher with symptoms suggestive of occupational asthma kept 2-hourly measurements of peak expiratory flow at home and at work, analysed using the occupational asthma system (OASYS) plotter, and/or had specific bronchial challenge testing to nitrogen trichloride, or a workplace challenge. Air measurement in one of the pools showed the nitrogen trichloride levels to be 0.1-0.57 mg x m(-3), which was similar to other studies. Two workers had peak expiratory flow measurements showing occupational asthma (OASYS-2 scores 2.88 and 3.8), both had a positive specific challenge to nitrogen trichloride at 0.5 mg x m(-3) with negative challenges to chlorine released from sodium hypochlorite. The third worker had a positive workplace challenge. Swimming-pool asthma due to airborne nitrogen trichloride can occur in workers who do not enter the water because of this chloramine. The air above indoor swimming pools therefore needs to be assessed and managed as carefully as the water.

Adult↗
PubMed2002

Noise exposure and hearing loss among student employees working in university entertainment venues.

OBJECTIVES: Most studies to date on sound levels in entertainment establishments have concentrated on exposure levels for the attending public, rather than employees who may be at greater risk of hearing loss. Of particular concern are young employees. The aim of this pilot study was to (i) estimate typical sound levels in different areas where amplified music was played, (ii) measure temporary threshold shift (TTS) and (iii) estimate the dependence of hearing threshold shifts on measured noise levels. METHODS: This study focused on students working part-time (up to 16 h/week) in music bars and discotheques in a university entertainment venue. All 28 staff were invited to participate in the study. Pre- and post-exposure audiometry was used to determine hearing threshold at both high and low frequencies. Personal dosemeters and static measurements were made to assess noise levels and frequency characteristics. A questionnaire was used to determine patterns of noise exposure and attitudes to noise levels and hearing loss. RESULTS: Of the 28 student employees working in the three areas, 14 (50%) agreed to take part in the study, giving 21 pre- and post-shift audiograms. The mean personal exposure levels for security staff were higher than those of bar staff, with both groups exceeding 90 dB(A). The maximum peak pressure reading for security staff was 124 dB. Although TTS values were moderate, they were found to be highly significant at both low and high frequencies and for both ears. Twenty-nine per cent of subjects showed permanent hearing loss of more than 30 dB at either low or high frequencies. The correlation between TTS and personal exposure was higher at 4 kHz than the low and high frequencies. CONCLUSIONS: Contemporary music may be an important yet little considered contributor to total personal noise exposure, especially amongst young employees. Employees need to be better informed of risks of hearing loss and the need to report changes in hearing acuity. Suggestions are made on strategies for improving the assessment of noise exposure in entertainment venues.

Adult↗
PubMed2001

Sensitisation to natural rubber latex: an epidemiological study of workers exposed during tapping and glove manufacture in Thailand.

OBJECTIVES: To estimate the prevalence of sensitisation to natural rubber latex in latex tappers and latex glove factory workers, and to relate this to airborne exposure to latex. METHODS: Five hundred workers employed in three latex glove factories, 314 tappers, and 144 college students (control group) were studied. The workers in the glove factories were classified into three exposure groups; high, moderate, and low. Personal exposures to natural rubber latex aeroallergens were measured by immunoassay. Symptom questionnaires and skin prick tests with latex allergens (Stallergènes 1:200 w/v) and other common environmental allergens were performed. The criterion for positivity was a wheal reaction at least 3 mm in diameter greater than that to a diluent control. RESULTS: The geometric mean (GM) concentration of latex in air was 15.4 microg/m(3) for those employed in glove stripping, glove inspections, and packing of powdered gloves. The moderate exposure glove manufacturing group and the tappers had GM concentrations of 2.3 and 2.4 microg/m(3) respectively, compared with United Kingdom users of latex powdered gloves,who had GM concentrations of 0.5 microg/m(3). The prevalence of sensitisation to latex in the tappers and latex glove factory workers was 1.3% and 1.7% respectively. No positive cases were found among the college students. Workers who showed a positive skin prick test to latex were more likely to be atopic. Work related respiratory and dermatological symptoms were found in about 20% of each population studied, but were not related to the presence of positive latex prick tests. CONCLUSIONS: This study suggests that in the Thai latex industries, latex sensitisation is rare despite high concentrations of airborne exposure and is less prevalent than in the healthcare sector in Europe where skin exposure is greater.

Adult↗
PubMed2001

Occupational health research priorities in Malaysia: a Delphi study.

OBJECTIVES: As part of a consultancy project on occupational health, the Delphi method was used to identify research priorities in occupational health in Malaysia. METHODS: Participation was sought from government ministries, industry, and professional organisations, and university departments with an interest in occupational and public health. Two rounds of questionnaires resulted in a final list of priorities, with noticeable differences between participants depending on whether they worked in industry or were from government organisations. RESULTS: The participation rate of 71% (55 of 78) was obtained for the first questionnaire and 76% (72 of 95) for the second questionnaire. The participants identified occupational health problems for specific groups and industries as the top research priority area (ranked as top priority by 25% of participants). Ministry of Health participants placed emphasis on healthcare workers (52% ranking it as top priority), whereas those from industry identified construction and plantation workers as groups, which should be accorded the highest priority. Evaluation of research and services was given a low priority. CONCLUSIONS: The priorities for occupational health determined with the Delphi approach showed differences between Malaysia, a developing country, and findings from similar European studies. This may be expected, as differences exist in stages of economic development, types of industries, occupational activities, and cultural attitudes to occupational health and safety. Chemical poisonings and workplace accidents were accorded a high priority. By contrast with findings from western countries, workplace psychosocial problems and musculoskeletal injuries were deemed less important. There also seemed to be greater emphasis on adopting interventions for identified problems based on experience in other countries rather than the need to evaluate local occupational health provisions.

Delphi Technique↗
PubMed2000

Natural rubber latex aeroallergen exposure in rubber plantation workers and glove manufacturers in Thailand and health care workers in a UK hospital.

OBJECTIVES: To estimate personal airborne natural rubber latex (NRL) concentrations for three occupational exposure groups; rubber plantation workers and NRL glove manufacturers in Thailand and health care workers in the UK. To utilise these data to classify the populations into appropriate exposure groups for the exposure-response analysis in the epidemiological study on latex allergy. METHODS: Two rubber plantations (110 workers), three NRL glove manufacturing factories (583 workers) in Thailand and one UK hospital (490 workers) were selected for the study. A preliminary workplace survey was carried out at each workplace in order to assign job titles subjectively in to high, moderate or low exposure groups for the purpose of sample selection. Between 5 and 20% of workers from each group for the three populations were then selected randomly for personal measurement of latex airborne allergens. Personal sampling was conducted using a 25 mm PTFE filter loaded in to an IOM sampling head at 2 l. min(-1). NRL aeroallergens were measured by an inhibition assay with NRL-specific IgE antibodies from NRL-sensitised people. RESULTS: A total of twenty-two personal samples were collected from plantation workers, sixty-one samples from the glove manufacturer employees and twenty seven from health care workers. The highest geometric mean (GM) NRL aeroallergen concentration was found in the glove manufacturing factories (7.3 microg m(-3)), followed by the rubber plantations (2.4 microg m(-3)) and the UK hospital (0.46 microg m(-3)). Amongst the NRL glove factories, the NRL aeroallergen concentrations were highest for those conducting the following tasks; glove stripping, glove inspections and packing of powdered gloves. The GM NRL aeroallergen for these tasks were in the range of 12.9 to 17.8 microg m(-3). CONCLUSIONS: In the process from tapping and manufacture of latex gloves through to their use the highest exposure to NRL aeroallergens is likely to occur in the manufacturing factories. Exposure to aeroallergens for the plantation workers was considered to be moderate and that of health care workers to be low.

Agriculture↗
PubMed1998

Oxidation of resin acids in colophony (rosin) and its implications for patch testing.

Commercial preparations of colophony (rosin) used for patch testing are made from unmodified rosin in pet. and may be stored for some considerable time before being used. This would be satisfactory if the composition and dermatological activity of the preparations were both reproducible and stable, but investigations by the authors have shown that the resin acids undergo progressive and substantial oxidation and that the dermatological activity of the preparations increases significantly with time. This may be a cause of inconsistent patch test results unless the composition can be stabilized. Gas liquid chromatography (GLC) analysis of a raw rosin sample and its commercial patch test preparation has shown that they both contained the same resin acids, but the concentration of the abietic type resin acids was found to be lower in the patch test preparations. The degradation of resin acids is due to their atmospheric oxidation, which may occur during the preparation and storage of the commercial rosin patch test preparation. The susceptibility of individual resin acids to atmospheric oxidation was demonstrated by analysing a sample of raw Portuguese gum rosin, which was then left exposed to air and light. Most of the resin acids were found to undergo oxidation at a rate which gradually diminished. More importantly, it is presumed that the concentration of oxidized resin acids increased correspondingly, and these have been shown to be more dermatologically active than the unoxidised resin acids. The rate of decrease of resin acid concentration was found to be in the following order: neoabietic>levopimaric and palustric>abietic>dehydroabetic acid. The pimaric type resin acids were found to be relatively inert to atmospheric oxidation when compared with the abietic type resin acids. Patch testing with the resulting partly oxidized Portuguese rosin produced positive reactions at a 35% higher frequency than the raw Portuguese rosin. The study demonstrates that the allergic potential of unmodified rosin may increase with exposure to air and light. It is therefore recommended that rosin preparations are analysed routinely as part of a quality control programme, which will enable better validation and comparison of patch test results from different dermatological centres. Since the oxidized resin acids are the main allergens in unmodified rosin, it is important that the concentration of the oxidized resin acids is kept high as well as constant in commercial patch test preparations.

Allergens↗
PubMed1997

High-performance liquid chromatography of unmodified rosin and its applications in contact dermatology.

Rosin is a well recognised skin sensitiser and is also amongst the most common causes of occupational asthma. Due to its complex chemical composition, it is difficult to isolate its many components and this has hindered progress in the identification of the specific respiratory and contact allergens it contains. This paper reports the application of high-performance liquid chromatography and other analytical techniques to the isolation and identification of contact allergens in complex mixtures such as rosin. HPLC methods were developed in order to isolate as many rosin components as possible and these were then patch tested on rosin sensitive individuals. The structure of the most dermatologically active component was then determined using mass spectrometry, nuclear magnetic resonance and infrared techniques. An HPLC method has also been developed which will enable the identification of rosin in commercial products, providing a valuable tool for determining the cause of rosin contact allergy. Furthermore, mass spectral data for the common abieitic-type resin acids are compiled which were used to confirm the identification of the HPLC resin acid peaks and have not been reported previously.

Allergens↗
PubMed1996

Identification of contact allergens in unmodified rosin using a combination of patch testing and analytical chemistry techniques.

In order to investigate the contact allergens in the unmodified colophony (rosin) used in routine patch testing, preparative chromatographic techniques were used to separate its components which were then patch tested on colophony-sensitive individuals. The chemical structure of the dermatologically active components was elucidated using mass spectrometry, nuclear magnetic resonance and infra-red techniques. The study shows that oxidized resin acids are stronger sensitizers than the resin acids themselves, the most potent contact allergen being 7-oxydehydroabietic acid (purity 92%). At naturally occurring concentrations (relative to abietic acid) all unoxidized resin acids were found to play an insignificant part, individually, in colophony dermatitis, except abietic acid (purity 99%), which was found to be a weak but important allergen. The commercial Trolab abietic acid preparation (unknown purity) was found to be dermatologically more active than purified abietic acid.

Abietanes↗
PubMed1995

Allergic potential of neutrals in unmodified colophony, and a method for their separation from resin acids.

An ion-exchange fractionation technique for the separation of total resin acid and neutral fractions of unmodified colophony is described. The allergic potential of these fractions was assessed by patch testing colophony-sensitive individuals, and this showed that both the neutral components and the resin acids play an important role in colophony sensitization. A greater frequency of positive reactions was obtained using the 60% colophony patch test preparation compared with the currently recommended 20% colophony preparation. Furthermore, some individuals were found to produce positive reactions to only the neutral components in colophony. We suggest that the use of a colophony patch test battery comprising resin acids, neutrals, oxidized resin acid and some colophony derivatives, will facilitate detection of colophony-sensitive individuals. Moreover, we consider that this will help to provide a better estimate of the prevalence of colophony dermatitis, which is currently underestimated.

Chemical Fractionation↗
PubMed1994

Colophony--uses, health effects, airborne measurement and analysis.

Colophony (rosin) is a widespread natural product obtained form species of the pine family Pinaceae. One of the most important uses of unmodified rosin is in electronic solder fluxes while the main areas of use of chemically modified rosin are paper sizing, adhesives, paints, varnishes, printing inks and plasticisers. Colophony is well recognized as a skin sensitizer and is also the third highest cause of occupational asthma. However, the specific allergens involved particularly in occupational asthma have not been comprehensively assessed or identified. This paper reviews method of colophony production, its uses and health effects and discusses the important issue of its chemical analysis and the choice of a suitable marker for monitoring colphony fume.

Air Pollutants, Occupational↗
PubMed1989

Occupational dermatitis from Synacril Red 3b liquid (CI Basic Red 22).

A carpet factory worker, exposed to a number of different dyes, developed a severe hand dermatitis. The handling of warm, wet and freshly-dyed yarn with unprotected hands was thought to have caused the onset of dermatitis. Patch testing indicated that the patient was sensitive to only one of the dyes handled, namely Synacril Red 3B liquid, which is based on the single dyestuff Basic Red 22 (CI 11055). Chemical analysis revealed the dyestuff to be of high purity (greater than 95%), suggesting that sensitization was caused by the Basic Red 22 dyestuff itself and not by an avoidable impurity.

Adult↗