Biomedical subjects

Scott A Guelcher

Publications and source records attributed to Scott A Guelcher.

3 recordsLinked to original sources

PubMed2006

Synthesis and in vitro biocompatibility of injectable polyurethane foam scaffolds.

The development of therapeutics for orthopedic clinical indications exploiting minimally invasive surgical techniques has substantial benefits, especially for treatment of fragility fractures in the distal radius of osteoporotics and vertebral compression fractures. We have designed six formulations of injectable polyurethane foams to address these clinical indications. The polyurethanes were prepared by mixing two liquid components and injecting the reactive liquid mixture into a mold where it hardens in situ. Porous polyurethane foams were synthesized from lysine methyl ester diisocyanate, a poly(epsilon-caprolactone-co-glycolide) triol, a tertiary amine catalyst, anionic and non-ionic stabilizers, and a fatty acid pore opener. The rise time of the foams varied from 8-20 min. The porosity was approximately 95% and the pores varied in size from 100-1000 microm. The polyurethane foams supported attachment of viable (>95%) MG-63 cells under dynamic seeding conditions. We anticipate compelling opportunities will be available as a consequence of the favorable biological and physical properties of the injectable polyurethane foams.

Animals↗

PubMed2005

Synthesis of biocompatible segmented polyurethanes from aliphatic diisocyanates and diurea diol chain extenders.

Many polyurethane elastomers display excellent mechanical properties and adequate biocompatibility. However, many medical-grade polyurethanes are prepared from aromatic diisocyanates and can degrade in vivo to carcinogenic aromatic diamines, although the question of whether the concentrations of these harmful degradation products attain physiologically relevant levels is currently unresolved and strongly debated. It is therefore desirable to synthesize new medical-grade polyurethanes from less toxic aliphatic diisocyanates. In this paper, biocompatible segmented polyurethane elastomers were synthesized from aliphatic diisocyanates (1,4-diisocyanatobutane (BDI) and lysine methyl ester diisocyanate (LDI)), novel diurea diol chain extenders based on tyrosine and tyramine, and a model poly(ethylene glycol) (PEG) diol soft segment. The objectives were to design a hard segment similar in structure to that of MDI-based polyurethanes and also investigate the effects of systematic changes in structure on mechanical and biological properties. The non-branched, symmetric polyurethane prepared from BDI and a tyramine-based chain extender had the highest modulus at 37 degrees C. Introduction of symmetric short-chain branches (SCBs) incorporated in the tyrosine-based chain extender lowered the modulus by an order of magnitude. Polyurethanes prepared from LDI were soft polymers that had a still lower modulus due to the asymmetric SCBs that hindered hard segment packing. Polyurethanes prepared from tyramine and tyrosine chain extenders thermally degraded at temperatures ranging from 110 to 150 degrees C, which are lower than that reported previously for phenyl urethanes. All four polyurethanes supported the attachment, proliferation, and high viability of MG-63 human osteoblast-like cells in vitro. Therefore, the non-cytotoxic chemistry of these polyurethanes make them good candidates for further development as biomedical implants.

Biocompatible Materials↗

PubMed2002

Two-particle dynamics on an electrode in ac electric fields.

The relative motion between pairs of negatively charged latex particles 9.7 microm in diameter and deposited on an electrode was measured by optical microscopy and image analysis. At an rms field of approximately 30 V cm(-1), the two particles moved toward each other at frequencies below 500 Hz, but they separated at 1000 Hz. In the cases of aggregation, there are several interesting characteristics. First, when the center-to-center separation of a pair was initially 6 particle radii or more apart, a transient 'incubation' period of tens of seconds was observed before the particles began to move toward each other. Second, the two particles never came into contact, rather at long times the pair maintained a stationary gap between them equal to approximately one-half the particle radius. This stationary gap between particles was also observed for the aggregation of clusters of three or more particles. Finally, the rate of approach for a pair of particles decreased as the frequency increased. Larger fields are required to move particles together in ac compared to dc fields; at 30 Hz the ac field must be 130 times greater than the dc field to achieve the same rate of approach. Taking advantage of the qualitative and quantitative differences of the cooperative motion of particles in dc vs. ac fields, one should be able to re-position particles by alternating between these two modes. We demonstrated that the same pair of particles can be brought together at low frequency (100 or 200 Hz) and then separated at high frequency (1000 Hz).

Journal Article↗