PubMed Health⌕ Search

Biomedical subjects

Seung-Man Yang

Publications and source records attributed to Seung-Man Yang.

17 recordsLinked to original sources
PubMed2006

Microwave-assisted self-organization of colloidal particles in confining aqueous droplets.

Monodisperse aqueous emulsion droplets encapsulating colloidal particles were produced in the oil phase, and controlled microwave irradiation of the aqueous drop phase created spherical colloidal crystals by so-called evaporation-induced self-organization of the colloidal particles. Unlike usual colloidal crystals, colloidal crystals in spherical symmetry (or photonic balls) possessed photonic band gaps for the normal incident light independent of the position all over the spherical surface. While the consolidation of colloidal particles in emulsion droplets in an oven took several hours, the present microwave-assisted evaporation could reduce the time for complete evaporation to a few tens of minutes. Under the microwave irradiation, the aqueous phase in emulsions was superheated selectively and the evaporation rate of water could be controlled easily by adjusting the microwave intensity. The result showed that the packing quality of colloidal crystals obtained by the microwave-assisted self-organization was good enough to show photonic band gap characteristics. The reflectance of our photonic balls responded precisely to any change in physical properties including the size of colloidal particles, refractive index mismatch, and angle of the incident beam. In particular, for polymeric particles, the photonic band gap could be tuned by the intensity of microwave irradiation, and the reflection color was red-shifted with stronger microwave irradiation. Finally, for better photonic band gap properties, inverted photonic balls were prepared by using the spherical colloidal crystals as sacrificial templates.

Journal Article↗
PubMed2006

Patterned arrays of au rings for localized surface plasmon resonance.

In this paper, we examined the characteristic behavior of localized surface plasmon resonances (LSPR) of Au dot and ring arrays in response to the selective binding of biomolecules. To do this, patterned arrays of Au rings and dots with various feature scales were fabricated over large areas by an imprint lithography technique. Our results showed that the LSPR spectra of the Au nanorings exhibited a blue shift with increase in the ring widths and asymptotically converged to those for Au nanodots. This clearly implies that the LSPR spectra can be tuned over an extended wavelength range by varying the ring width. For an illustrative purpose, the patterned Au structures were used to detect the binding of streptavidin to biotin. In doing this, the Au patterns were chemically modified with G4 dendrimers of amine terminated poly(amidoamine), which facilitated the tethering of biotin onto the Au pattern. Exposure of the biotinylated Au nanorings to aqueous streptavidin solution induced both red-shifts of the LSPR spectra and changes in the peak intensities. The sensitivity of the LSPR spectra to the binding of the biomolecules was enhanced as the ring width of Au rings was decreased.

Biotin↗
PubMed2006

High-speed fabrication of patterned colloidal photonic structures in centrifugal microfluidic chips.

In this paper, we report a rapid and facile method for fabricating colloidal photonic crystals inside microchannels of radially symmetric microfluidic chips which were made using soft-lithography. As the suspension of monodisperse silica or polystyrene latex spheres was driven to flow through the channels under the action of centrifugal force, the colloidal spheres were quickly assembled into face centered cubic arrangement which had a few photonic stop bands. The soft-microfluidic channels and cells confined the colloidal crystals into designed patterns. The optical reflectance was modulated by the refractive-index mismatch between the colloidal particles and the solvent in the interstices between the particles. Therefore, the present microfluidic chips with built-in colloidal photonic crystals can be used as in-situ optofluidic microsensors for high throughput screening or light filters in integrated adaptive optical devices.

Colloids↗
PubMed2006

Fabrication of one-dimensional colloidal assemblies from electrospun nanofibers.

Electrospun nanofibers were used as confining geometries for fabricating 1-D colloidal assemblies. Silica particles dispersed in several different polymer solutions were cast into nanofibers by an electrospinning process. The silica particle configurations were examined in terms of the size ratio of silica particles to nanofibers and the properties of the dispersing medium. As the electrospun fiber was extended highly, the silica particles dispersed in the polymer solution began to assemble spontaneously into a pearl-necklace structure. We also demonstrated the alignment of 1-D silica assemblies using a designed configuration of collector electrodes.

Chemistry↗
PubMed2006

Nanoscopic Pd line arrays using nanocontact printed dendrimers.

High-density Pd line arrays with 55 nm line-width were obtained using nanocontact-printed dendrimer monolayers. Elastomeric PDMS stamps for nanocontact printing were replicated from silicon master molds which were fabricated by UV nanoimprinting in combination with reactive ion etching. The fabrication method effectively controlled the aspect ratios of high-density lines for resolving the problems encountered in both replicating silicon masters to PDMS stamps and printing with the replicated PDMS stamps. Using the PDMS nanostamp with an optimized aspect ratio, a self-assembled monolayer of dendrimer was patterned on a Pd film via nanocontact printing, which was facilitated by the strong interaction between Pd and amine groups of the dendrimer. The patterned self-assembled monolayer was used as an etch-resist mask against the wet etchant of Pd, leaving behind a high-density Pd line array over large areas. The resulting functional Pd nanopattern is of practical significance in microelectronics and bio- or gas-sensing devices.

Journal Article↗
PubMed2006

Nanomachining by colloidal lithography.

Colloidal lithography is a recently emerging field; the evolution of this simple technique is still in progress. Recent advances in this area have developed a variety of practical routes of colloidal lithography, which have great potential to replace, at least partially, complex and high-cost advanced lithographic techniques. This Review presents the state of the art of colloidal lithography and consists of three main parts, beginning with synthetic routes to monodisperse colloids and their self-assembly with low defect concentrations, which are used as lithographic masks. Then, we will introduce the modification of the colloidal masks using reactive ion etching (RIE), which produces a variety of nanoscopic features and multifaceted particles. Finally, a few prospective applications of colloidal lithography will be discussed.

Colloids↗
PubMed2005

Self-organization of bidisperse colloids in water droplets.

Most of the colloidal clusters have been produced from oil-in-water emulsions with identical microspheres dispersed in oil droplets. Here, we present new types of binary colloidal clusters from phase-inverted water-in-oil emulsions using various combinations of two different colloids with several size ratios: monodisperse silica or polystyrene microspheres for larger particles and silica or titania nanoparticles for smaller particles. Obviously, a better understanding of how finite groups of different colloids self-organize in a confined geometry may help us control the structure of matter at multiple length scales. In addition, since aqueous dispersions have much better phase stability, we could produce much more diverse colloidal materials from water-in-oil emulsions rather than from oil-in-water emulsions. Interestingly, the configurations of the large microspheres were not changed by the presence of the small particles. However, the arrangement of the smaller particles was strongly dependent on the nature of the interparticle interactions. The experimentally observed structural evolutions were consistent with the numerical simulations calculated using Surface Evolver. These clusters with nonisotropic structures can be used as building blocks for novel colloidal structures with unusual properties or by themselves as light scatterers, diffusers, and complex adaptive matter exhibiting emergent behavior.

Journal Article↗
PubMed2005

Fabrication of spherical colloidal crystals using electrospray.

We demonstrated the use of electrohydrodynamic atomization to prepare uniform-sized emulsion droplets in which equal spheres of silica or polystyrene were dispersed. The size of the emulsion droplets was easily controlled by the electric field strength and the flow rate, independently of the diameter of the nozzles. During the evaporation of solvent in the droplets, spherical colloidal crystals were formed by self-assembly of the monodisperse colloidal spheres. The diameter of the spherical colloidal crystals was in the range of 10-40 microm. Depending on the stability of colloidal particles, the morphology of the self-assembled structure was varied. In particular, silica spheres in ethanol droplets were self-assembled into compactly packed silica colloidal crystals in spherical shapes, whereas polystyrene latex spheres in toluene droplets self-assembled into spherical colloidal crystal shells with hollow cores. The silica colloidal assemblies reflected diffraction colors according to the three-dimensionally ordered arrangement of silica spheres.

Colloids↗
PubMed2005

Connected open structures from close-packed colloidal crystals by hyperthermal neutral beam etching.

We report the fabrication of connected open structures from close-packed colloidal crystals by hyperthermal neutral beam etching. Colloidal crystal films of polystyrene microspheres were prepared by a vertical deposition method. Exposure of the colloidal crystal films to hyperthermal neutral beam made isolated microspheres in the face-centered cubic lattice, each of which was connected with its twelve nearest neighbors through very thin cylinders. Due to the charge neutrality of impinging gas molecules of the hyperthermal neutral beam, the spherical shape of polymer microspheres was almost maintained during the etching process. The Bragg reflection peaks were modulated by the etched volume of colloidal crystals. Finally, the inverse structures of such open structures were replicated by a simple room-temperature chemical vapor deposition and subsequently burning out polymer template spheres.

Colloids↗
PubMed2005

Fabrication of hollow colloidal crystal cylinders and their inverted polymeric replicas.

We fabricated colloidal crystals on a fiber by a dip-coating method. The self-assembly of monodisperse colloidal particles was affected by the curvature of the fiber (the reciprocal of the fiber radius). As the fiber became smaller in diameter, fewer layers of the colloidal spheres were coated for a given lift-up speed. The hollow colloidal crystal cylinders were used as a template for creating macroporous structure having three-dimensionally interconnected air cavities. Specifically, the polymer precursor was infiltrated into the colloidal crystal template and the macroporous polymer structures were obtained after the selective etching of colloidal particles.

Journal Article↗
PubMed2005

Particle arrays with patterned pores by nanomachining with colloidal masks.

In summary, we have developed a new strategy for the fabrication of arrayed colloidal particles well-ordered nanometric holes of three or four fold symmetry by anisotropic reactive ion (plasma) etching of self-organized layers of colloidal spheres. We demonstrated that a mesoporous silica matrix with regular open windows could be used as a lithographic mask and the resulting arrangement of pores on a particle was dependent on the orientation of the colloidal particle stacking. A variety of organic and inorganic materials such as metals for metal-polymer composites, DNA and proteins, semiconducting and ceramic materials, and other polymers and small chemicals can be incorporated via chemical and physical attachment. Particles with patterned pores and composite particles by our nanomachining process can be used as novel functional materials in the field of electronics, photonics, and biotech areas.

Journal Article↗
PubMed2004

Colloidal lithographic nanopatterning via reactive ion etching.

We report here a novel colloidal lithographic approach to the fabrication of nonspherical colloidal particle arrays with a long-range order by selective reactive ion etching (RIE) of multilayered spherical colloidal particles. First, layered colloidal crystals with different crystal structures (or orientations) were self-organized onto substrates. Then, during the RIE, the upper layer in the colloidal multilayer acted as a mask for the lower layer and the resulting anisotropic etching created nonspherical particle arrays and new patterns. The new patterns have shapes that are different from the original as a result of the relative shadowing of the RIE process by the top layer and the lower layers. The shape and size of the particles and patterns were dependent on the crystal orientation relative to the etchant flow, the number of colloidal layers, and the RIE conditions. The various colloidal patterns can be used as masks for two-dimensional (2-D) nanopatterns. In addition, the resulting nonspherical particles can be used as novel building blocks for colloidal photonic crystals.

Journal Article↗
PubMed2003

Estimation of zeta potential by electrokinetic analysis of ionic fluid flows through a divergent microchannel.

The streaming potential is generated by the electrokinetic flow effect within the electrical double layer of a charged solid surface. Surface charge properties are commonly quantified in terms of the zeta potential obtained by computation with the Helmholtz-Smoluchowski (H-S) equation following experimental measurement of streaming potential. In order to estimate a rigorous zeta potential for cone-shaped microchannel, the correct H-S equation is derived by applying the Debye-Hückel approximation and the fluid velocity of diverging flow on the specified position. The present computation provides a correction ratio relative to the H-S equation for straight cylindrical channel and enables us to interpret the effects of the channel geometry and the electrostatic interaction. The correction ratio decreases with increasing of diverging angle, which implies that smaller zeta potential is generated for larger diverging angle. The increase of Debye length also reduces the correction ratio due to the overlapping of the Debye length inside of the channel. It is evident that as the diverging angle of the channel goes to nearly zero, the correction ratio converges to the previous results for straight cylindrical channel.

Journal Article↗
PubMed2003

Effect of two-step sol-gel reaction on the mesoporous silica structure.

In the present study, we investigated the effects of two-step sol-gel reaction by abrupt pH change on the SBA-15 and mesocellular silica foams (MCF). Mesoporous silica was fabricated by using triblock copolymer templates (poly(ethylene oxide) and poly(propylene oxide)). The prepared silica structure was characterized by X-ray diffraction, transmission electron microscopy, and N(2) sorption experiment. Specifically, we prepared SBA-15 with long-range two-dimensional hexagonal arrangement of 3 to 6-nm feature spacing and MCF with larger pores of a few tens of nanometers. The pore size and ordering were influenced by pH change in a two-step sol-gel reaction and the concentration of organic solvent. Although well-ordered hexagonal arrangement of mesopores was prevalent in acidic conditions, the materials synthesized by a single-step reaction in neutral or basic conditions possessed gel-like structure without mesopores. However, the present two-step reaction (low pH sol-gel reaction followed by high pH reaction) not only produced mesoporous materials but also provided controllability of the pore size. In particular, mesoporous structures with pore sizes as large as those of MCF were successfully fabricated by the two-step reaction without using organic swelling agents. As expected, when xylene was added as a swelling agent, the pore size increased with the xylene/copolymer weight ratio.

Ammonium Hydroxide↗
PubMed2002

Packings of uniform microspheres with ordered macropores fabricated by double templating.

Highly uniform 3-D ordered macroporous spheres in regular arrays were produced by a double templating process. The first template of larger silica balls produced the polymer skeleton for guiding the shape and size of the self-assembled superstructure of smaller polymeric balls, which are introduced subsequently into the internal space of the skeleton. The second templating with inorganic precursors has created novel superstructured materials, which could open up significant opportunities in a variety of areas ranging from absorbents/catalysts to novel photonic crystals.

Journal Article↗
PubMed2002

Hydrodynamic interaction between spheres coated with deformable thin liquid films.

In this article, we considered the hydrodynamic interaction between two unequal spheres coated with thin deformable liquids in the asymptotic lubrication regime. This problem is a prototype model for drop coalescence through the so-called "film drainage" mechanism, in which the hydrodynamic contribution comes dominantly from the lubrication region apart from the van der Waals interaction force. First, a general formulation was derived for two unequal coated spheres that experienced a head-to-head collision at a very close proximity. The resulting set of the evolution equations for the deforming film shapes and stress distributions was solved numerically. The film shapes and hydrodynamic interaction forces were determined as functions of the separation distance, film thickness, viscosity ratios, and capillary numbers. The results show that as the two spheres approach each other, the films begin to flatten and eventually to form negative curvature (or a broad dimple) at their forehead areas in which high lubrication pressure is formed. The dimple formation occurs earlier as the capillary number increases. For large capillary numbers, the film liquids are drained out from their forehead areas and the coated liquid films rupture before the two films "touch" each other. Meanwhile, for small capillary numbers, the gap liquid is drained out first and the two liquid films eventually coalesce.

Journal Article↗