Biomedical subjects

Seung-Muk Yi

Publications and source records attributed to Seung-Muk Yi.

4 recordsLinked to original sources

PubMed2005

Comparison between back-trajectory based modeling and Lagrangian backward dispersion modeling for locating sources of reactive gaseous mercury.

Reactive gaseous mercury (RGM) was measured using an annular denuder coated with potassium chloride at three rural sites (Potsdam, Stockton, and Sterling) in New York State from April 2002 to April 2003. Concentrations of RGM ranged from 0.1 to 84.6 pg m(-3) with large spatial and temporal variation. Potential source contribution function (PSCF), a common receptor modeling tool, was used with these measurements, and source-receptor relationships were calculated using back-dispersion and deposition as well as back-trajectories. Modeling results were compared with the RGM emissions inventory, and Spearman rank-order correlation coefficients were calculated. PSCF results incorporating backward dispersion and deposition were better correlated with the emissions inventory than PSCF based on back-trajectories alone. This difference was determined to be mainly due to the inclusion of dispersion rather than deposition. The main sources of RGM were suggested to be coal-fired power plants in New York and Pennsylvania, the large copper smelter in Quebec, and the taconite mining areas around the Great Lakes.

Air Movements↗

PubMed2004

Evaluating the effect of daily PM10 variation on mortality.

Many epidemiological studies have shown the association between daily mortality and daily average of PM(10) level. Daily average of PM(10) has been used for regression type time-series analysis. This article suggests that daily mean mortality is not only a function of daily mean but also a function of daily standard deviation of PM(10). We used generalized additive Poisson regression model with overdispersion parameter to investigate this hypothesis using the data from Seoul, Korea, from 1997 to 2001. One interquartile range (IQR = 42.11 microg/m(3)) increase of daily mean level of PM(10) was found to be associated with 2.1% increase of additional daily mortality (RR = 1.021, 95% CI = 1.009-1.035) after controlling for other confounders. Similarly, we also found that one IQR (11.93 microg/m(3)) increase in daily standard deviation of PM(10) is associated with 2.5% increase of additional risk of death (RR = 1.025, 95% CI = 1.000-1.028) when other covariates remained the same. These findings may provide new insight into the possible explanation of health effect of PM(10) and support the hypothesis that PM(10) deviation is also an important risk factor after controlling for daily mean PM(10) level.

Air Pollutants↗

PubMed2004

Measurement of ultrafine particle size distributions from coal-, oil-, and gas-fired stationary combustion sources.

Currently, we have limited knowledge of the physical and chemical properties of emitted primary combustion aerosols and the changes in those properties caused by nucleation, condensation growth of volatile species, and particle coagulations under dilution and cooling in the ambient air. A dilution chamber was deployed to sample exhaust from a pilot-scale furnace burning various fuels at a nominal heat input rate of 160 kW/h(-1) and 3% excess oxygen. The formation mechanisms of particles smaller than 420 nm in electrical mobility diameter were experimentally investigated by measurement with a Scanning Mobility Particle Sizer (SMPS) as a function of aging times, dilution air ratios, combustion exhaust temperatures, and fuel types. Particle formation in the dilution process is a complex mixture of nucleation, coagulation, and condensational growth, depending on the concentrations of available condensable species and solid or liquid particles (such as soot, ash) in combustion exhausts. The measured particle size distributions in number concentrations measured show peaks of particle number concentrations for medium sulfur bituminous coal, No. 6 fuel oil, and natural gas at 40-50 nm, 70-100 nm, and 15-25 nm, respectively. For No. 6 fuel oil and coal, the particle number concentration is constant in the range of a dilution air ratio of 50, but the number decreases as the dilution air ratio decreases to 10. However, for natural gas, the particle number concentration is higher at a dilution air ratio of 10 and decreases at dilution air ratios of 20-50. At a dilution air ratio of 10, severe particle coagulation occurs in a relatively short time. Samples taken at different combustion exhaust temperatures for these fuel types show higher particle number concentrations at 645 K than at 450 K. As the aging time of particles increases, the particles increase in size and the number concentrations decrease. The largest gradient of particle number distribution occurs within the first 10 sec after dilution but shows only minor differences between 10 and 80 sec. The lifetimes of the ultrafine particles are relatively short, with a scale on the order of a few seconds. Results from this study suggest that an aging time of 10 sec and a dilution air ratio of 20 are sufficient to obtain representative primary particle emission samples from stationary combustion sources.

Aerosols↗

PubMed2003

Measured summertime concentrations of particulate components, Hg0, and speciated polycyclic aromatic hydrocarbons at rural sites in New York State.

Daily PM2.5 samples, Hg0 and speciated polycyclic aromatic hydrocarbon (PAH) were simultaneously collected at Potsdam and Stockton site in NY during the summers of 2000 and 2001. Samples for determination of the mass concentration and chemical composition of the PM2.5 were obtained with a speciation network PM2.5 sampler. Chemical composition including trace elemental composition, water-soluble ions, and elemental carbon were analyzed. Elemental mercury and PAHs were sampled separately. Daily PM2.5 concentrations ranged from 0.47 to 53.7 microg m(-3) at the Potsdam site, and from 0.82 to 47.23 microg m(-3) at the Stockton site with large daily differences between the two sites. Potsdam consistently had lower mass values than Stockton. The greatest contributors to the PM2.5 mass (generally >0.1 microg/m(3)) were sulfate, nitrate, ammonium, and BC at both sites. Seventeen PAHs were identified at each site in 2000 and the average total concentrations were 3.2 ng/m(3) and 2.9 ng/m(3) at the Potsdam and Stockton sites, respectively. The mean vapor phase mercury concentration at the Potsdam site (2.4 +/-1.2 ng m(-3), n=93) was higher than that at the Stockton site (1.2 +/- 1.0 ng m(-3), n=60) in 2000, whereas in 2001, the average concentrations were 1.1 ng m(-3) and 1.6 ng m(-3) at the Potsdam and Stockton sites, respectively. In general, vapor phase mercury concentrations increased with increasing ambient temperature at the Stockton site in 2000. These differences in values between 2000 and 2001 can be largely explained by distinct differences in the meteorological regimes that dominated in the different years.

Aerosols↗