PubMed Health⌕ Search

Biomedical subjects

Shaochen Chen

Publications and source records attributed to Shaochen Chen.

5 recordsLinked to original sources

Immobilized nerve growth factor and microtopography have distinct effects on polarization versus axon elongation in hippocampal cells in culture.

Cell interfacing with biomaterial surfaces dictates important aspects of cell behavior. In particular, axon extension in neurons is effectively influenced by surface properties, both for the initial formation of an axon as well as for the maintenance of axon growth. Here, we investigated how neurons behaved on poly(dimethyl siloxane) (PDMS) surfaces decorated with biochemical and physical cues presented individually or in combination. In particular, nerve growth factor (NGF) was covalently tethered to PDMS to create a bioactive surface, and microtopography was introduced to the material in the form of microchannels. Embryonic hippocampal neurons were used to investigate the impact of these surface cues on polarization (i.e., axon initiation or axogenesis) and overall axon length. We found that topography had a more pronounced effect on polarization (68% increase over controls) compared to immobilized NGF (0.1 ng/mm(2)) (27% increase). However, the effect of NGF was negligible when both types of stimuli were simultaneously presented on the biomaterial surface. In addition to axon formation, chemical and physical cues are also involved in axon growth following the initiation process. Interestingly, for the same studies described above, the effects of microchannels and NGF were opposite from the effects on polarization; the most evident effect was for the immobilized growth factor (10% increase in axon length with respect to controls) whereas there was no effect in general for the microtopography. More importantly, when the two surface stimuli were presented in combination, a synergistic increase in axon length was detected (25% increase with respect to controls), which could be a result of faster polarization triggered by topography plus enhanced growth from NGF. Additionally, axon orientation was also analyzed and we found the well-known tendency of perpendicular or parallel axonal alignment to be dependent on the width and depth of the channels. This investigation thoroughly compared and distinguished the individual and combined impact of material surface properties (chemical and physical) on axogenesis from the effects on axon length. Overall, topography dominated polarization mechanisms, whereas NGF, and particularly a synergy of immobilized NGF plus topography, dominated axon length. These results could be potentially applied for the design of biomaterials in applications were axon growth is critical.

Animals↗

A digital micro-mirror device-based system for the microfabrication of complex, spatially patterned tissue engineering scaffolds.

Our ability to create precise, pre-designed, spatially patterned biochemical and physical microenvironments inside polymer scaffolds could provide a powerful tool in studying progenitor cell behavior and differentiation under biomimetic, three-dimensional (3D) culture conditions. We have developed a simple and fast, layer-by-layer microstereolithography system consisting of an ultra-violet light source, a digital micro-mirror masking device, and a conventional computer projector, that allows fabrication of complex internal features along with precise spatial distribution of biological factors inside a single scaffold. Photo-crosslinkable poly(ethylene glycol) diacrylates were used as the scaffold material, and murine bone marrow-derived cells were successfully encapsulated or seeded on fibronectin-functionalized scaffolds. Fluorescently-labeled polystyrene microparticles were used to show the capability of this system to create scaffolds with complex internal architectures and spatial patterns. We demonstrate that precisely controlled pore size and shapes can be easily fabricated using a simple, computer-aided process. Our results further indicate that multi-layered scaffolds with spatially distributed factors in the same layer or across different layers can be efficiently manufactured using this technique. These microfabricated scaffolds are conducive for osteogenic differentiation of marrow-derived stem cells, as indicated by efficient matrix mineralization.

Animals↗

Disposable polydimethylsiloxane/silicon hybrid chips for protein detection.

This paper presents disposable protein analysis chips with single- or four-chamber-constructed from poly(dimethylsiloxane) (PDMS) and silicon. The chips are composed of a multilayer stack of PDMS layers that sandwich a silicon microchip. This inner silicon chip features an etched array of micro-cavities hosting polymeric beads. The sample is introduced into the fluid network through the top PDMS layer, where it is directed to the bead chamber. After reaction of the analyte with the probe beads, the signal generated on the beads is captured with a CCD camera, digitally processed, and analyzed. An established bead-based fluorescent assay for C-reactive protein (CRP) was used here to characterize these hybrid chips. The detection limit of the single-chamber protein chip was found to be 1 ng/ml. Additionally, using a back pressure compensation method, the signals from each chamber of the four-chamber chip were found to fall within 10% of each other.

C-Reactive Protein↗

Laser-layered microfabrication of spatially patterned functionalized tissue-engineering scaffolds.

Understanding cell behavior inside complex, three-dimensional (3D) microenvironments with controlled spatiotemporal patterning of physical and biochemical factors would provide significant insights into the basic biology of organ development and tissue functions. One of the fundamental limitations in studying such behavior has been the inability to create patterned microenvironments within 3D scaffold structures. Here a simple, layer-by-layer stereolithography (SL) method that can precisely pattern ligands, extracellular-matrix (ECM) components, and growth factors, as well as controlled release particles inside a single scaffold, has been developed. The process also allows fabrication of predesigned internal architectures and porosities. Photocrosslinkable poly(ethylene glycol) dimethacrylate (PEGDMA) was used as the basic structural component of these microfabricated scaffolds. PEG acrylates, covalently modified with the cell adhesive peptide arginine-glycine-aspartic acid (RGD) or the ECM component heparan sulfate, was incorporated within the scaffolds to facilitate cell attachment and to allow spatial sequestration of heparan-binding growth factors. Fluorescently labeled polymer microparticles and basic fibroblast growth factor (FGF-2) were chosen to illustrate the capability of SL to spatiotemporally pattern scaffolds. The results demonstrate that a precise, predesigned distribution of single or multiple factors within a single 3D structure can be created, and specific internal architectures can be fabricated. Functionalization of these scaffolds with RGD is demonstrated, and heparan sulfate allows efficient cell attachment and spatial localization of growth factors. Such patterned scaffolds might provide effective systems to study cell behavior in complex microenvironments and could eventually lead to engineering of complex, hybrid tissue structures through predesigned, multilineage differentiation of a single stem-cell population.

Animals↗

Direct micro-patterning of biodegradable polymers using ultraviolet and femtosecond lasers.

Thin films of biodegradable polymeric materials, poly(epsilon-caprolactone) (PCL) and poly(glycolic acid) (PGA) were micro-patterned using a Ti-sapphire femtosecond pulsed laser and ArF excimer UV laser in ambient conditions. The laser-patterned polymers were characterized using a scanning electron microscope (SEM), Fourier transform infrared spectroscopy in attenuated total reflectance mode (FTIR-ATR) and X-ray photoelectron spectroscopy (XPS). In-vitro degradation tests were performed and the laser-patterned samples showed to be within one standard deviation of the control samples. Our results demonstrate that both lasers are excellent tools for micro-patterning biodegradable polymers since the bulk properties of the material can remain intact and because the direct-write method is rapid, flexible, and a chemical-free process.

Aluminum Oxide↗