Biomedical subjects

Shin-Tson Wu

Publications and source records attributed to Shin-Tson Wu.

9 recordsLinked to original sources

PubMed2006

Highly tunable large-core single-mode liquid-crystal photonic bandgap fiber.

We demonstrate a highly tunable photonic bandgap fiber, which has a large-core diameter of 25 microm and an effective mode area of 440 microm2. The tunability is achieved by infiltrating the air holes of a photonic crystal fiber with an optimized liquid-crystal mixture having a large temperature gradient of the refractive indices at room temperature. A bandgap tuning sensitivity of 27 nm/degrees C is achieved at room temperature. The insertion loss is estimated to be less than 0.5 dB and caused mainly by coupling loss between the index-guided mode and the bandgap-guided mode.

Journal Article↗

PubMed2005

Polymer-based flexible microlens arrays with hermaphroditic focusing properties.

Polymer microlens arrays with hermaphroditic focusing behaviors are demonstrated. Each microlens in an arrays exhibits either converging or diverging focus, depending on the polarization direction of the incident light. A polymer film with patterned microlens arrays is flexible, lightweight, and ultrathin (approximately 50 microm). Details of the lens structure, device fabrication, and lens performance are described.

Journal Article↗

PubMed2005

Variable optical attenuator with a polymer-stabilized dual-frequency liquid crystal.

A transmission-type variable optical attenuator (VOA) based on a polymer-stabilized dual-frequency liquid crystal (PSDFLC) is demonstrated at gamma = 1.55 microm. The VOA is highly transparent in the voltage-off state but scatters light in the voltage-on state. By using a birefringent beam displacer incorporated with half-wave plates, we can obtain a VOA that is polarization independent and that exhibits a 31 dB dynamic range. The polymer networks and dual-frequency effect together reduce the response time (rise + decay) of a 16 microm PSDFLC cell to 30 ms at room temperature and at a voltage of 24 Vrms.

Journal Article↗

PubMed2005

Patterning polymerized lipid vesicles with soft lithography.

The applications of soft lithography in patterning polymerized lipid vesicles of 1,2-bis(tricosa-10,12-diynoyl)-sn-glycero-3-phosphocholine on glass substrates are reported. We demonstrate that the polymerized vesicles can be used as a high molecular weight ink to be transferred from a PDMS stamp onto a glass substrate to form two-dimensional stripes with a controlled separation. By combining channel flow with dewetting within microfluidic networks, we assemble the polymerized vesicle into three-dimensional stripes and one-dimension lines on glass substrates. Atomic force microscopy shows that these patterned vesicle structures are stable on glass substrates. The simple, stable, and precise immobilization of lipid vesicles on solid substrates will open up the possibility of integrating them in biosensors and microelectronic devices.

Journal Article↗

PubMed2005

Hermaphroditic liquid-crystal microlens.

We demonstrate a flat microlens that exhibits hermaphroditic focusing properties. When the input polarization is parallel (perpendicular) to the liquid-crystal directors, the lens exhibits a positive (negative) focal length. To select the proper polarization, we could rotate the polarizer (or the lens) mechanically or by use of an electrically controlled twisted nematic liquid-crystal cell. Details of the lens structure and of the device's fabrication and performance are described.

Journal Article↗

PubMed2005

Reflective liquid-crystal displays with asymmetric incident and exit angles.

The 2 x 2 matrix methods are extended to calculate the optical behaviors of reflective liquid-crystal displays with asymmetric incident and exit angles. Both the unfolding method and the backward-eigenwave method are employed to derive the 2 x 2 matrix representations. The simulation results for symmetric incident and exit angles from these two methods are identical and agree well with those obtained from the 4 x 4 matrix method when the air-panel surface reflections are neglected. Further, the derived 2 x 2 matrix methods are applied to the asymmetric cases with different incident and exit angles. The simulated results on the normally black vertical alignment and normally white mixed-mode twisted nematic reflective displays show reasonably good agreement with the reported experimental data. In addition, a rubbing effect related to contrast values is observed and analyzed in asymmetric reflective cases. We also find that this effect has a significant influence on the contrast ratios once the difference between the incident and exit angles becomes large.

Journal Article↗

PubMed2004

All-optical display using photoinduced anisotropy in a bacteriorhodopsin film.

Photoinduced anisotropy in a bacteriorhodopsin film using the pump-probe method was investigated. A diode-pumped second-harmonic YAG laser was used as the pump beam, and three wavelengths, at lambda = 442, 532, 655 nm, from different lasers were used as probe beams. Without the pump beam, the probe light cannot transmit the analyzer to the detector. However, because of photoinduced anisotropy, a portion of the probe light is detected when the pump beam is present. Based on this property, we demonstrate a full-color all-optical display.

Anisotropy↗

PubMed2004

Liquid-crystal microlens arrays using patterned polymer networks.

A real-time dynamically tunable-focus microlens array made from a polymer-liquid-crystal (LC) composite is demonstrated. The polymer was first patterned in microlens array cavities by lamination, and the LC-monomer mixture was then injected to the molded polymer cavities and finally stabilized by UV light-induced networks. Using this new fabrication method, we demonstrated a lens with a spherical shape and a glazed surface. This LC-based microlens can reach approximately 100% light efficiency for linearly polarized light. The saturation voltage of the lens is approximately 60 Vrms, and the response time is approximately 30 ms.

Journal Article↗

PubMed2004

Applications of multidirectional asymmetrical microlens-array light-control films on reflective liquid-crystal displays for image quality enhancement.

The multidirectional asymmetrical microlens-array light-control film (MAMA-LCF) is developed for enhancing the image brightness and contrast ratio of various reflective liquid-crystal displays. By use of index-matching material, the interface reflection is greatly reduced. Through optimized designs, the surface-scattering effect is also suppressed; thus the contrast ratio is much enhanced. From experimental results, the MAMA-LCF leads to a approximately 1.5 x gain in brightness over the MgO standard white and a 15:1 contrast ratio for the reflective color super-twist nematic liquid-crystal display, 2.8 x MgO and a 23:1 contrast ratio for the polymer-dispersed liquid-crystal, and 2.8 x MgO and a 13:1 contrast ratio for the cholesteric liquid-crystal display. Potential applications of this low-cost plastic thin film for reflective liquid-crystal displays are foreseeable.

Journal Article↗