PubMed Health⌕ Search

Biomedical subjects

T Engström

Publications and source records attributed to T Engström.

5 recordsLinked to original sources
PubMed2002

A method for evaluation of manual work using synchronised video recordings and physiological measurements.

Industrial interventions that focus on increased productivity may impair the ergonomics, on a workstation or individual level. This paper presents a method that characterises work time consumption and physical work load of manual work, using video recordings synchronised with physiological measurements of, e.g. muscular activity, and postures. The underlying idea was that it is possible to amalgamate technical and human aspects resulting in a synergetic evaluation. The method was developed through two case studies within the Swedish automotive industry, where manual materials handling was studied. A methodological result was that the synchronising procedure was sufficiently precise to allow work activities to be assigned significantly different levels of physical work load. These different levels may be used to predict physical work load in the design and change of production systems. It was concluded that the method is accurate enough to be a useful tool in industrial interventions.

Automobiles↗
PubMed1999

Musculoskeletal symptoms due to technical preconditions in long cycle time work in an automobile assembly plant: a study of prevalence and relation to psychosocial factors and physical exposure.

The aim was to evaluate the prevailing ergonomic conditions in a parallelized flow, long cycle time, assembly system. The evaluation focused on physical exposure, psychosocial factors and work-related musculoskeletal symptoms. A random sample of 67 assembly operators was included in a cross-sectional study mainly based on questionnaires. Hand/wrist symptoms were common and related to work exposure with hand-held powered tools. In general, the self-reported physical exposure showed only a few significant associations with musculoskeletal symptoms. This may in part be explained by the ergonomic conditions generally being good, with a relatively low duration of 'combined' extreme work postures. Significant associations were found between the psychosocial work environment and musculoskeletal symptoms.

Adult↗
PubMed1998

Variability in the skin exposure of machine operators exposed to cutting fluids.

OBJECTIVE: This study describes a new technique for measuring skin exposure to cutting fluids and evaluates the variability of skin exposure among machine operators performing cyclic (repetitive) work. METHODS: The technique is based on video recording and subsequent analysis of the video tape by means of computer-synchronized video equipment. The time intervals at which the machine operator's hand was exposed to fluid were registered, and the total wet time of the skin was calculated by assuming different evaporation times for the fluid. The exposure of 12 operators with different work methods was analyzed in 6 different workshops, which included a range of machine types, from highly automated metal cutting machines (ie, actual cutting and chip removal machines) requiring operator supervision to conventional metal cutting machines, where the operator was required to maneuver the machine and manually exchange products. RESULTS: The relative wet time varied between 0% and 100%. A significant association between short cycle time and high relative wet time was noted. However, there was no relationship between the degree of automatization of the metal cutting machines and wet time. CONCLUSIONS: The study shows that skin exposure to cutting fluids can vary considerably between machine operators involved in manufacturing processes using different types of metal cutting machines. The machine type was not associated with dermal wetness. The technique appears to give objective information about dermal wetness.

Adult↗
PubMed1996

Ergonomics in parallelized car assembly: a case study, with reference also to productivity aspects.

In 1985 Volvo started the development of a new plant for the assembling of cars. This plant was situated in the town of Uddevalla in Sweden. One deliberate aim with this plant was to combine an enhanced productivity and product quality with good ergonomics conditions and improved work organization. The plant was designed with a production system where parallel work-teams of about five persons could assemble from 1/4 up to complete cars. A newly developed tilting device, a piece of equipment that could rotate, rise and lower the car body in order to facilitate assembly work, was introduced. Ergonomic analyses of postural and musculoskeletal strain showed that parallelized flow production, according to the production principles of the Uddevalla plant, was superior to traditional car assembly according to the serial flow production concept, i.e. the traditional assembly line. It was noted that this ergonomic standard was implemented without compromising productivity. In conclusion, increased knowledge and experience of parallelized production systems has been gained which should be considered in the development of future assembly plants, even though the Uddevalla factory itself was closed down in 1993.

Journal Article↗