Biomedical subjects

T Griebe

Publications and source records attributed to T Griebe.

5 recordsLinked to original sources

PubMed2001

Agarose hydrogels as EPS models.

For investigating the influence of extracellular polymeric substances (EPSs) on biofilm properties, artificial models of defined composition and structure can be very helpful. Different immobilised cell systems can be useful in the fitting of experimental results. Two different types of of artificial EPS matrix model were developed earlier. Homogeneous agarose beads (50-500 microns diameter) and porous beads (260 microns mean diameter) containing pores with diameters from 10 to 80 microns (28 microns on average), allowed the embedding of cells, particles and typical EPS matrix components such as proteins and polysaccharides. In this paper, some physico-chemical properties of the artificial EPS matrices were described and compared with results known from natural EPS. The stability of the artificial matrix polymer against solution in the aqueous medium was studied in batch experiments. The water binding and water retaining capabilities of the EPS models were investigated by drying and re-swelling experiments. The simulation of protective effects of the artificial EPS matrix against toxic substances like biocides in comparison to such known protective effects of the EPS of native biofilms were proved by the application of sodium hypochlorite (0.5 mg/l, 30 min) and subsequent microscopic investigation of the cell population after LIVE/DEAD staining (Molecular Probes).

Biofilms↗

PubMed2001

A new method for extraction of extracellular polymeric substances from biofilms and activated sludge suitable for direct quantification of sorbed metals.

A method for extraction of extracellular polymeric substances (EPSs) with a dicyclohexyl-18-crown-6 ether was developed to determine levels of organic and inorganic contaminants sorbed to EPS. The crown ether selectively binds alkaline and alkaline earth metals but not heavy metals. The effectiveness of the extraction procedure was higher than that of 2 other methods tested and comparable with that of a method based on a cation exchange resin. On average it was possible to extract 20% of the TOC, 12% of the total protein content, and 4% of the total carbohydrate content of sludge or biofilm biomass. Metal sorption studies in activated sludge showed no influence of exposure time on the fractionation of metals within the biomass. Metals sorbed mostly to cellular material. In biofilms 12.2% of the cadmium and 9.1% of the zinc added was found in the EPS. In activated sludge EPS contained only 2.9% zinc. The distribution of metals within the biomass was dose dependent. The percentage of metals found in EPS decreased with increasing metal concentration. This indicates a higher affinity of metals for cellular binding sites. Time course experiments in a rotating biofilm annular reactor, which consisted of an external cylinder with removable slides and an internal solid drum, revealed a gradual change in zinc concentration associated with EPS, although the total zinc concentration in the biomass remained constant. Concurrently, the amount of extractable EPS decreased. This was a consequence of a microbial population shift, with bacterial counts decreasing and algal and fungal biomass increasing. Using confocal laser scanning microscopy and the fluorescent metal complexing agent Newport Green for in situ detection of zinc it was shown that metals were bound to algae and fungi in the latter part of the experiment. The biofilm became more and more heterogeneous coinciding with a decrease in EPS. To summarize, the observed sorption behavior of metals cannot be explained with the conventional paradigm of EPS as hydrophilic gel. Obviously, different binding mechanisms must be invoked to explain the role of EPS in the sorption and removal of toxic substances in activated sludge and biofilm systems. It is important to consider the microbial population to understand differences in sorption in different matrices.

Adsorption↗

PubMed2000

Artificial biofilm model--a useful tool for biofilm research.

For biofilm studies, artificial models can be very helpful in studying processes in hydrogels of defined composition and structure. Two different types of artificial biofilm models were developed. Homogeneous agarose beads (50-500 microm diameter) and porous beads (260 microm mean diameter) containing pores with diameters from 10 to 80 microm (28 microm on average) allowed the embedding of cells, particles and typical biofilm matrix components such as proteins and polysaccharides. The characterisation of the matrix structures and of the distribution of microorganisms was performed by confocal laser scanning microscopy. The physiological condition of the embedded bacteria was examined by redox activity (CTC-assay) and membrane integrity (Molecular Probes LIVE/DEAD-Kit). Approximately 35% of the immobilised cells (Pseudomonas aeruginosa SG81) were damaged due to the elevated temperature required for the embedding process. It was shown that the surviving cells were able to multiply when provided with nutrients. In the case of homogeneous agarose beads, cell growth only occurred near the bead surface, while substrate limitation prevented growth of more deeply embedded cells. In the porous hydrogel, cell division was observed across the entire matrix due to better mass transport. It could be shown that embedding in the artificial gel matrix provided protection of immobilized cells against toxic substances such as sodium hypochlorite (0.5 mg/l, 30 min) in comparison to suspended cells, as observed in other immobilized systems. Thus, the model is suited to simulate important biofilm matrix properties.

Biofilms↗

PubMed1994

Comparison of respiratory activity and culturability during monochloramine disinfection of binary population biofilms.

Biofilm bacteria challenged with monochloramine retained significant respiratory activity, even though they could not be cultured on agar plates. Microbial colony counts on agar media declined by approximately 99.9% after 1 h of disinfection, whereas the number of bacteria stained by a fluorescent redox dye experienced a 93% reduction. Integrated measures of biofilm respiratory activity, including net oxygen and glucose utilization rates, showed only a 10 to 15% reduction. In this biofilm system, measures of microbial respiratory activity and culturability yielded widely differing estimates of biocide efficacy.

Chloramines↗

PubMedDate not supplied

Enzymatic activity in the activated-sludge floc matrix.

The enzymatic activity of activated sludge was investigated with special emphasis on the localization of the enzymes in the sludge floc matrix. Activated sludge from an advanced activated-sludge treatment plant, performing biological N and P removal, was used. An enzymatic fingerprint was established using a panel of six different enzymes. The fingerprint revealed peptidase as the most dominating specific enzyme tested. By monitoring sludge bulk enzymatic activity over a 3-month period using fluorescein diacetate as an enzyme substrate, considerable variations in activity were observed even over short periods (a few days). The variation in esterase activity was to some extent correlated to the presence of humic compounds in the sludge, but not to the sludge protein content. Comparison of full sludge enzyme activity to the activity of a batch-grown sludge culture indicated that enzymes accumulated in sludge flocs. A large proportion of the exoenzymes were immobilized in the sludge by adsorption in the extracellular polymeric substances (EPS) matrix. This was demonstrated by extraction of EPS from the activated sludge using cation exchange. Contemporary to the release of EPS a very large fraction of the exoenzymes was released into the water. This showed that the exoenzymes should be considered to be an integrated part of the EPS matrix rather than as direct indicators of the microbial activity or biomass.

Enzymes↗