Biomedical subjects
Publications and source records attributed to T J Mason.
This paper describes recent studies in organic sonoelectrochemistry at Coventry University, including the oxidation of thiophene monoxides, degradation of dye pollutants, formation of conducting polymers and electrosynthetic modification of proteins.
In order to obtain maximum ultrasonic effect upon electrochemical silver recovery, mass transfer measurements were investigated. The effect on limiting current of changing the position of an ultrasonic horn tip (i.e. vertical and horizontal) and using a cylinder electrode (CE), was studied in an attempt to find the optimum position required for maximum sonoelectrochemical effect. The importance of the ultrasonic intensity, the electrode-horn distance and positioning (angle) in assigning limiting currents was also investigated. For the CE placed at an angle of 45 degrees with respect to the ultrasonic horn, it was suggested that the 50% increase in limiting current for the 'face-on' geometry is caused by an approximately 50% decrease in diffusion layer thickness for the 'face-on' geometry compared to the 'angular' geometry due to the difference in the sonicated areas for both geometries.
Some species of bacteria produce colonies and spores which agglomerate in spherical clusters (Bacillus subtilis) and this serves as a protection for the organisms inside against biocidal attack. Flocs of fine particles e.g. clay can entrap bacteria which can also protect them against the biocides. It is because of problems such as these that alternative methods of disinfecting water are under active investigation. One such method is the use of power ultrasound, either alone or in combination with other methods. Ultrasound is able to inactivate bacteria and deagglomerate bacterial clusters or flocs through a number of physical, mechanical and chemical effects arising from acoustic cavitation. The aim of this study was to investigate the effect of power ultrasound at different powers and frequencies on Bacillus subtilis. Viable plate count techniques were used as a measure of microbial activity. Results showed a significant increase in percent kill for Bacillus species with increasing duration of exposure and intensity of ultrasound in the low-kilohertz range (20 and 38 kHz). Results obtained at two higher frequencies (512 and 850 kHz) indicated a significant increase in bacteria count suggesting declumping. In assessing the bacterial kill with time under different sonication regimes three types of behaviour were characterized: High power ultrasound (lower frequencies) in low volumes of bacterial suspension results in a continuous reduction in bacterial cell numbers i.e. the kill rate predominates. High power ultrasound (lower frequencies) in larger volumes results in an initial rise in cell numbers suggesting declumping of the bacteria but this initial rise then falls as the declumping finishes and the kill rate becomes more important. Low intensity ultrasound (higher frequencies) gives an initial rise in cell numbers as a result of declumping. The kill rate is low and so there is no significant subsequent decrease in bacterial cell numbers.
In the past there was a prevailing feeling in industry that power ultrasound would be too expensive to use for water treatment on an industrial scale. This was based on calculations involving the direct scale up of power consumption in small-scale (generally batch) laboratory experiments. In recent times this attitude has changed somewhat as a result of the installation of a number of ultrasonic devices in operational water or sewage treatment plants. In our laboratories we have investigated the decontamination of water under the influence of ultrasound alone and in conjunction with other treatments. The results, particularly when applied to flowing systems, indicate a real future for sonochemistry in water treatment.
There is an increasing incidence in health problems related to environmental issues that originate from inadequate treatment of potable waters. This has compelled scientists and engineers to engage in innovative technologies to achieve a maximum disinfection at affordable costs. Some species of bacteria produce colonies and spores that can agglomerate in spherical clusters and thus protect organisms on the inside of the cluster against biocidal attack. Flocs of fine particles (e.g., clay) can entrap bacteria and this can also protect them against the biocides. Other bacteria have the ability to mutate, thus building up resistance to conventional biocides (e.g., chlorine). Ultrasound has been shown to be effective in improving the effectiveness of biocides such as chlorine. The aim of this present study was to investigate the effect of electrolysis and power ultrasound as a disinfection treatment and to provide a greater knowledge of the fundamentals of disinfection through the production of hypochlorite in situ from saline solution via electrolysis. The electrode materials investigated were, carbon (felt and graphite), copper and stainless steel rods. The results show that sonication appears to amplify the effect of electrolysis. A combination of both treatments is significantly better than sonication or electrolysis alone.
Ultrasound was found to increase the oxidation peak current and hence the decomposition rate of thiosulphate 50-fold compared to silent conditions. The effects of the ultrasonic frequency (20 and 38 kHz) and power upon the electrochemical oxidation of thiosulphate in aqueous KCl (1 mol dm-3) at stationary stainless steel and platinum electrodes were studied chronoamperometrically and potentiostatically (at various scan rates). No sigmoidal-shaped voltammograms were observed for the redox couple S4O6(2-)/S2O3(2-) in the presence of ultrasound. However, application of ultrasound to this redox couple provided an increase in the oxidation peak current at the frequencies employed, the magnitude of which varied with concentration, scan rate and ultrasonic power. Under sonication at 20 and 38 kHz, the oxidation peak potential shifted anodically with increasing ultrasonic power. This anodic shift in potential may be due to the formation of hydroxyl radicals, changes in electrode surface composition and complex adsorption phenomena. The large increase in oxidation peak currents and the rates of decomposition of thiosulphate, in the presence of ultrasound, are explained in terms of enhanced mass transfer at the electrode due to cavitation and acoustic streaming together with microstreaming coupled with adsorption phenomena. It is also shown that changes in macroscopic temperature throughout the experiment are insufficient to cause the observed enhanced diffusion.
A mixture of benzoyl chloride and nitrobenzene is not known to be chemically reactive, indeed the mixture is chemically inert when subjected individually to either ultrasonic irradiation or heating. However, if this system is initially subjected to ultrasound and then heated for several hours at 200 degrees C, a reaction does occur and the products are benzoic anhydride, hydrochloric acid, nitrous and nitric acid together with some minor products. To the best of our knowledge, this is the first example of a reaction where the effect of ultrasound does not appear to be the consequence of the direct action of acoustic cavitation bubbles. A possible explanation of this behaviour is advanced which involves an electron transfer reaction in which nitrobenzene is first activated by ultrasound and then acts as oxidant in the thermal stage of reaction.
The paper reports the enhanced effect of multi-frequency ultrasonic irradiation on cavitation yield. The cavitation yield is characterized by electrical conductivity determination, fluorescence intensity determination and iodine release method. Two-frequency (28 kHz/0.87 MHz) orthogonal continuous ultrasound, two-frequency (28 kHz/0.87 MHz) orthogonal pulse ultrasound and three-frequency (28 kHz/1.0 MHz/1.87 MHz) orthogonal continuous ultrasound have been used. It has been found that the combined irradiation of two or more frequencies of ultrasound can produce a significant increase in cavitation yield compared with single frequency irradiation. The possible mechanisms of the enhanced effect are briefly discussed.
Ultrasonic irradiation applied either above the surface of a chromic acid plating bath or through the plating bath itself during the process of chromium electroplating reduces the emissions of hazardous chromic acid mist The use of ultrasound is particularly effective at high current densities. The results suggest that sonication during the electroplating of chromium may provide a useful method of controlling chrome mist emission without the need for a chemical additive (mist suppressant). In conjunction with lip extraction this could lead to a more efficient process since the use of ultrasound has been shown to be of benefit in the electroplating process itself.
The paper presents an insight into the mechanism of the ultrasonic enhancement of solvent extraction through the effect of ultrasound on the vegetal material involved. Thus, a series of experiments has been developed to investigate the effect of ultrasonic energy on the vegetal material and the solvent used. Several results concerning the ultrasonic extractive value, ultrasonic swelling index and the effects of frequency on vegetal material are presented.
Experiments related to the industrial production of medicinal tinctures of sage (Salvia officinalis L.) and valerian (Valeriana officinalis L.) were performed using ultrasonically assisted extraction and quality of the final tincture was evaluated by gas chromatography and dry residue determination. The constituents of the active sage compound: borneol, cineole, alpha- and beta-thujone and also the dry residue were measured. In the case of valerian extractions, the efficiency of sonicated extraction was compared with classical extraction. The course of only the dry residue was monitored. The influence of ultrasound on the quality of valerian tincture was examined by HPLC.
The efficiency of extraction of rutin from Sophora japonica is improved by ultrasound but is dependent on the solvent employed. Rutin is a compound with antioxidant activity and aqueous solvents appear to be unsuitable for ultrasonic extractions due to the formation of free radicals from the insonation of the solvent. The application of ultrasound to methanolic extraction gave a significant reduction in extraction time and an increase in maximum yield.
This paper describes the influence of 20 kHz ultrasound upon the corrosion behaviour of zinc in NaOH electrolytes. A systematic study of the effects exerted by ultrasound on the electrochemical interface was first carried out, so as to determine the transmitted power and to characterize mass transfer at the electrode. Then attention was focused on the corrosion passivation mechanism of zinc in sonicated NaOH solutions (0.1 and 1 M). Investigations were carried out using electrochemical techniques to determine corrosion and passivation kinetics parameters. SEM analysis of the sonicated zinc surfaces provides complementary information on the oxide layer composition and structure.
Investigations have been performed on various methods of increasing cavitation activity measured by the intensity of sonoluminescence. It is shown that the effect of the combined action of (a) pulsed modulation of an acoustic field, (b) liquid degassing and cooling and (c) increasing the static pressure considerably exceeds the sum of the effects achieved by each of these methods individually. A more than 250-fold increase of the sonoluminescence intensity has been attained compared with continuous irradiation under normal conditions (room temperature, atmospheric pressure, gas-saturated liquid). An interpretation of the results obtained is proposed.
The present work has been carried out in order to design a new type of ultrasonic reactor consisting of a double-structured tank. The inner working compartment is built with a slant bottom to allow a better ultrasonic transmission. This paper reports the effect of the inclination angle on acoustic efficiency for several different plates, e.g. two plates made of glass (2 mm and 3 mm thickness) and one made of PVC (3 mm thickness). The acoustic efficiency was determined as the ratio of the signal measured by a hydrophone in the presence of the plate to that signal in the absence of the plate. Having optimised the system, the ultrasonic powers in the inner and the outer compartments of the slant bottom reactor were determined by hydrogen peroxide dosimetry.
It has been recognised for many years that power ultrasound has great potential in a wide variety of processes in the chemical and allied industries. Some of these processes have been known for many years and continue to flourish as major commercial applications, e.g. plastic welding and cleaning. Others, like ultrasonic drilling, while showing great potential have not been widely exploited to date. The potential for the industrial use of power ultrasound is enormous, and yet industry seems somewhat reluctant to adopt it. In this article the existing uses of power ultrasound in processing are reviewed and the potentials are explored.
Solutions of the acidic dye, Sandolan Yellow, were subjected to sonolysis, electrolysis and sonoelectrolysis. Decolourisation did not take place using ultrasound alone but was achieved using an electro-oxidation process. The rate of electro-chemical decolourisation in the absence of ultrasound was dependent on the type of electrode used, electrolyte concentration, reaction temperature and the current density. Electro-oxidation of Sandolan Yellow using platinum electrodes was enhanced using ultrasound when carried out in a semi-sealed cell, which minimised the effects of ultrasonic degassing.
Granular pieces of brick impregnated with copper oxide were used as a model for contaminated soil. Washing this model substrate by passing water across the substrate on an ultrasonically shaken tray irradiation afforded a 40% reduction in copper content. This was compared with only a 6% reduction when the sample was treated under otherwise identical conditions but using a tray shaken conventionally. The majority of the copper was removed as a result of the removal of surface materials which were more heavily contaminated with the copper oxide.