PubMed Health⌕ Search

Biomedical subjects

T Kissel

Publications and source records attributed to T Kissel.

At least 55 records · Page 3Linked to original sources
PubMed1999

Biodegradable recombinant human erythropoietin loaded microspheres prepared from linear and star-branched block copolymers: influence of encapsulation technique and polymer composition on particle characteristics.

Recombinant human erythropoietin (EPO) and fluorescein isothiocyanate labeled dextran (FITC-dextran) loaded microspheres were prepared by a modified W/O/W double-emulsion technique. Biodegradable linear ABA block copolymers consisting of poly(L-lactide-co-glycolide) A blocks attached to central poly(ethyleneoxide) (PEO) B blocks and star-branched AB block copolymers containing A blocks of poly(L-lactide) or poly(L-lactide-co-glycolide) and star-branched poly(ethyleneoxide) B blocks were investigated for their potential as sustained release drug delivery systems. Microsphere characteristics were strongly influenced by the polymer composition. In the case of the linear block copolymers, a reduced lactic acid content in a linear block copolymer yielded smaller particles, a lower encapsulation efficiency, and a higher initial drug release both in the case of EPO and FITC-dextran. The investigation of the effects of several manufacturing parameters on microsphere formation showed that the process temperature plays an important role. Microsphere formation in a +1 degrees C environment resulted in higher drug loadings without increasing the amount of residual dichloromethane inside the particles. Other parameters such as the homogenization of the primary W/O emulsion and of the W/O/W double-emulsion have less impact on microsphere characteristics. Branched block copolymers containing star-shaped PEO also showed potential for the preparation of drug loaded microspheres. A certain amount of glycolic acid in the copolymer was necessary for the successful preparation of non-aggregating microspheres at room temperature. Again, the processing temperature strongly affected particle characteristics. Microsphere preparation at +1 degrees C allows the formation of microspheres from a polymer not containing glycolic acid, a result which could not be achieved at room temperature. Moreover, compared to microsphere formation at room temperature, the effective FITC-dextran loading was increased. Concerning the EPO loaded microspheres, the amount of EPO aggregated was comparable to that using the linear ABA polymers. A continuous release of the protein from these star-shaped polymers could not be achieved. In conclusion, apart from microsphere preparation in a +1 degrees C environment the choice of the polymer represents the main factor for a successful entrapment of proteins into biodegradable microspheres.

Biodegradation, Environmental↗
PubMed1999

Tetracycline-HCl-loaded poly(DL-lactide-co-glycolide) microspheres prepared by a spray drying technique: influence of gamma-irradiation on radical formation and polymer degradation.

Tetracycline-HCl (TCH)-loaded microspheres were prepared from poly(lactide-co-glycolide) (PLGA) by spray drying. The drug was incorporated in the polymer matrix either in solid state or as w/o emulsion. The spin probe 4-hydroxy-2,2,6, 6-tetramethyl-piperidine-1-oxyl (TEMPOL) and the spin trap tert-butyl-phenyl-nitrone (PBN) were co-encapsulated into the TCH-loaded and placebo particles. We investigated the effects of gamma-irradiation on the formation of free radicals in polymer and drug and the mechanism of chain scission after sterilization. Gamma-Irradiation was performed at 26.9 and 54.9 kGy using a 60Co source. The microspheres were characterized especially with respect to the formation of radicals and in vitro polymer degradation. Electron paramagnetic resonance (EPR) spectroscopy, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), high-performance liquid chromatography (HPLC), gas chromatography-mass spectroscopy (GC-MS), and scanning electron microscopy (SEM) were used for characterization of the microspheres. Using EPR spectroscopy, we successfully detected gamma-irradiation induced free radicals within the TCH-loaded microspheres, while unloaded PLGA did not contain radicals under the same conditions. The relatively low glass transition temperature of the poly(dl-lactide-co-glycolide) (37-39 degrees C) seems to favor subsequent reactions of free radicals due to the high mobility of the polymeric chains. Because of the high melting point of TCH (214 degrees C), the radicals can only be stabilized in drug loaded microspheres. In order to determine the mechanism of polymer degradation after exposure to gamma-rays, the spin trap PBN and the spin probe TEMPOL were encapsulated in the microspheres. gamma-Irradiation of microspheres containing PBN resulted in the formation of a lipophilic spin adduct, indicating that a polymeric radical was generated by random chain scission. Polymer degradation by an unzipping mechanism would have produced hydrophilic spin adducts of PBN and monomeric radicals of lactic or glycolic acid. These degradation products were not detected by EPR. This result is confirmed by the observation that possible diamagnetic reaction products of low molecular weight, consisting of TEMPOL and lactide or glycolide monomers, could not be detected by GC-MS. While an irradiation dose-dependent decrease in molecular weight of PLGA could be verified in agreement with the literature, TCH content of the microspheres was not affected by the exposure to gamma-rays. It can be concluded that EPR spectroscopy in combination with GPC, DSC, and HPLC allows a detailed characterization of the impact of gamma-sterilization on biodegradable parenteral drug delivery systems.

Anti-Bacterial Agents↗
PubMed1999

Biodegradable microspheres containing influenza A vaccine: immune response in mice.

A monovalent influenza split vaccine was microencapsulated in poly(D,L-lactic-co-glycolic acid) (PLGA) and ABA triblock copolymers using a W/O/W double emulsion technique. To stabilize the antigen, influenza vaccine was also coencapsulated with liposomes. Antigen release from microspheres was determined in vitro using a hemagglutinin-specific ELISA. PLGA-microspheres with liposomes released immunoreactive hemagglutinin in a pulsatile manner, a preferred feature for the development of a single dose vaccine delivery system. Influenza hemagglutinin specific IgG and neutralizing antibody responses were studied in BALB/c mice following subcutaneous injection of different microsphere preparations. PLGA-microspheres elicited a significantly higher primary IgG response compared to nonencapsulated antigen. ABA-microspheres seemed to be less immunogenic than PLGA-microspheres based on the IgG antibody response, however, similar levels of neutralizing antibodies were observed after eight weeks with both polymers. Entrapment of the antigen in liposomes prior to microencapsulation did not further enhance the immune response. The immunopotentating effect of the antigen-loaded microspheres was prominently enhanced when they were given as suspension in fluid antigen, suggesting that free antigen may serve as priming and microencapsulated antigen as booster dose. Eight weeks after a single subcutaneous immunization with PLGA or ABA-microspheres neutralizing antibodies were as high as those obtained after two subcutaneous administrations of fluid vaccine four weeks apart. Microencapsulated influenza antigen may have potential for a single dose vaccine delivery system with adjuvant properties.

Animals↗
PubMed1999

Cell type specificity of the human endoglin promoter.

Endoglin is a component of the transforming growth factor-beta receptor complex whose expression is limited to a small number of cell types, including endothelial cells (ECs), activated monocytes, tissue macrophages and erythroid precursors. Of particular interest is its preferential expression in the vasculature of many malignant tumors, especially in view of potential therapeutic applications. We have cloned the human endoglin promoter, analyzed its structure and demonstrate that the isolated genomic fragment shows strong promoter activity in ECs (compared to other known EC-selective promoters), but not in epithelial cells and fibroblasts. These findings suggest that the endoglin promoter may prove a useful tool for the transcriptional targeting of ECs by gene therapy. We also determined the domains that are responsible for both efficient transcription and the observed preferential activity in ECs. The region around the major site of transcription initiation was found to be essential for transcription in both ECs and non-ECs. In contrast, cell type specificity does not appear to be governed by a single mechanism, but rather seems to be due to functionally distinct regulatory mechanisms acting on different upstream sequences.

3T3 Cells↗
PubMed1999

A novel non-viral vector for DNA delivery based on low molecular weight, branched polyethylenimine: effect of molecular weight on transfection efficiency and cytotoxicity.

PURPOSE: Low molecular weight branched polyethylenimine (LMW-PEI) was synthesized and studied as a DNA carrier for gene delivery with regard to physico-chemical properties, cytotoxicity, and transfection efficiency. METHODS: The architecture of LMW-PEI, synthesized by acid catalyzed ring-opening polymerization of aziridine was characterized by size exclusion chromatography in combination with laser light scattering and 13C-NMR-spectroscopy. In vitro cytotoxic effects were quantified by LDH and MTT assay and visualized by transmission electron microscopy. The potential for transgene expression was monitored in ECV304 cells using luciferase driven by a SV40 promotor as reporter gene system. RESULTS: LMW-PEI (Mw 11'900 D) with a low degree of branching was synthesized as a DNA carrier for gene delivery. In contrast to high molecular weight polyethylenimines (HMW-PEI; Mw 1'616'000 D), the polymer described here showed a different degree of branching and was less cytotoxic in a broad range of concentrations. As demonstrated by transmission electron microscopy the LMW-PEI formed only small aggregates which were efficiently taken up by different cells in the presence of serum, most likely by an endocytic pathway. LMW-PEI yielded transfection efficiencies measured via expression of the reporter gene luciferase which were up to two orders of magnitude higher than those obtained with HMW-PEI. The reporter gene expression was concentration dependent, but in contrast to lipofection independent of serum addition. CONCLUSIONS: The LMW-PEI described here is a new, highly efficient, and non-cytotoxic vector with a favorable efficiency/toxicity profile for gene therapeutic applications.

Animals↗
PubMed1999

Prodrug approach for alphaIIbbeta3-peptidomimetic antagonists to enhance their transport in monolayers of a human intestinal cell line (Caco-2): comparison of in vitro and in vivo data.

PURPOSE: Different lipophilic derivatives of a potent alphaIIbbeta3-antagonist with benzamidino-oxazolidinone structure were investigated with respect to transport and metabolism properties to evaluate their potential as prodrugs with improved absorption behavior. METHODS: Intestinal transport and metabolism of the compounds were studied in Caco-2 monolayers under in vitro conditions and quantitated by a reversed-phase HPLC- method. Peroral bioavailability in cynomolgus monkeys and inhibition of platelet aggregation (guinea pig) were compared to in vitro permeability coefficients. RESULTS: N-alkoxycarbonyl- and N-benzoyl-derivatization of the benzamidine-parent drug increased the apparent permeabilities across Caco-2 monolayers by a factor of 25-100 fold. Most prodrugs were transported mainly by passive diffusion, whereas the methoxycarbonyl-derivative EMD 122347 displayed directional transport from basolateral (BL) to apical (AP). This polarized efflux was concentration dependent (saturable kinetics with Km = 207 microM, Vmax = 0.275 nmol cm(-2) min(-1)) and could be reduced in the presence of verapamil (300 microM), an inhibitor of p-glycoprotein. Cell mediated cleavage of the prodrugs was low and showed only slight differences to hydrolysis in buffer solution, indicating a predominantly non enzymatic cleavage. Both peroral bioavailability (monkey) and the inhibition of ex-vivo platelet aggregation (guinea pig) gave the same rank order as the permeability coefficients obtained in Caco-2 monolayers. CONCLUSIONS: Alkoxycarbonylamidine- and benzoylamidine promoieties of a RGD mimetic alphaIIbbeta3-antagonist considerably increased both effect bioavailabilities in animal experiments as well as in-vitro permeability in cell monolayers, demonstrating the potential of this approach to enhance transport of peptidomimetic drugs.

Animals↗
PubMed1998

Erythropoietin loaded microspheres prepared from biodegradable LPLG-PEO-LPLG triblock copolymers: protein stabilization and in-vitro release properties.

Biodegradable microspheres containing recombinant human Erythropoietin (EPO) were prepared from ABA triblock copolymers, consisting of hydrophobic poly(l-lactic-co-glycolic acid) A blocks and hydrophilic polyethylenoxide (PEO) B blocks. Different polymer compositions were studied for the microencapsulation of EPO using a modified double-emulsion process (W/O/W). The encapsulation efficiency for EPO, ranging from 72% to 99% was quite acceptable. The formation of high molecular weight EPO aggregates, however, was higher than in poly(d,l-lactide-co-glycolide) (PLG) microparticles. Using different excipients with known protein stabilizing properties, such as Bovine Serum Albumin (BSA), Poly-l-Histidine (PH), Poly-l-Arginine (PA) or a combination of PA with Dextran 40 (D40), the EPO aggregate content was significantly reduced to <5% of the encapsulated EPO. In contrast to PLG, ABA triblockcopolymers containing >7 mol % PEO, allowed a continuous release of EPO from microspheres for up to 2 weeks under in-vitro conditions. The release profile was comparable to FITC-Dextran 40 kDa (FD 40) loaded microspheres in the initial release phase, while EPO release was leveling off at later time points. BSA additionally prolonged the EPO release, while blends of PLG and PEO did not generate continuous EPO release profiles. LPLG-PEO-LPLG triblock-copolymers (35 mol % PEO; 30 kDa) in combination with 5% BSA yielded both an acceptable level of EPO aggregates and a continuous release profile under in-vitro conditions for up to 2 weeks. The formation of EPO aggregates at later time points is probably induced by acidic cleavage products of the biodegradable polymer and requires further optimization of the ABA polymer composition.

Biocompatible Materials↗
PubMed1998

Synthesis of bioadhesive poly(acrylic acid) nano- and microparticles using an inverse emulsion polymerization method for the entrapment of hydrophilic drug candidates.

Bioadhesive latices of water-swollen poly(acrylic acid) nano-and microparticles were synthesized using an inverse (W/O) emulsion polymerization method. They are stabilized by a co-emulsifier system consisting of SpanTM 80 and TweenTM 80 dispersed in aliphatic hydrocarbons. The initial polymerization medium contains emulsion droplets and inverse micelles which solubilize a part of the monomer solution. The polymerization is initiated by free radicals, and particle dispersions with a narrow size distribution are obtained. The particle size is dependent on the type of radical initiator used. With water-soluble initiators, for example ammonium persulfate, microparticles were obtained in the size range of 1 to 10 micrometer indicating that these microparticles originate from the emulsion droplets since the droplet sizes of the W/O emulsion show similar distribution. When lipophilic radical initiators, such as azobis-isobutyronitrile, are used, almost exclusively nanoparticles are generated with diameters in the range of 80 to 150 nm, due to the limited solubility of oligomeric poly(acrylic acid) chains in the lipophilic continuous phase. These poly(acrylic acid) micro- and nanoparticles yielded excellent bioadhesive properties in an in-vitro assay and may, therefore, be suitable for the encapsulation of peptides and other hydrophilic drugs.

Acrylic Resins↗
PubMed1998

Biocompatibility testing of ABA triblock copolymers consisting of poly(L-lactic-co-glycolic acid) A blocks attached to a central poly(ethylene oxide) B block under in vitro conditions using different L929 mouse fibroblasts cell culture models.

The biocompatibility of ABA triblock copolymers consisting of poly(L-lactide-co-glycolide) A blocks attached to a central poly(ethylene oxide), (PEO), B block was investigated under in vitro conditions. The ABA triblock copolymer was compared to commercially available Poly(D,L-lactide-co-glycolide) (PLGA) and reference materials in different L929 cell culture models according to the procedure recommended by the International Standard Organization (ISO). Different preparation methods: namely extraction, indirect contact and direct contact with polymer samples were compared. The extraction method seems to be the most sensitive assay, allowing estimates of IC50 values. ABA and PLGA polymers showed excellent compatibility with L929 fibroblasts with all preparation techniques used. The influence of polymer composition and molecular weight on degradation rate as well as in vitro biocompatibility was then investigated. Changes in pH and osmolarity as well as lactic acid content of the extracts were determined and compared to in vitro degradation data of polymer films in phosphate buffered saline at 37 degreesC evaluating molecular weight (GPC) and massloss (gravimetry). An acceleration of the degradation rate of the ABA triblock copolymers with increasing PEO content was observed. The in vitro cytotoxicity studies demonstrated that the three ABA polymers were well tolerated by fibroblasts in cell culture. One ABA polymer batch ABA2 showed unusual in vitro cytotoxicity in L929 fibroblasts, possibly related to the molecular weight of the PEO used for this particular batch or residual glycolic acid. Cell culture models for biocompatibility testing of polymers according to ISO are useful as screening models in characterizing biodegradable polymers, but they cannot replace animal testing. The extraction method in combination with the MTT assay allows quantitative ranking of cytotoxic properties with high sensitivity.

Animals↗
PubMed1998

Plasma protein adsorption on biodegradable microspheres consisting of poly(D,L-lactide-co-glycolide), poly(L-lactide) or ABA triblock copolymers containing poly(oxyethylene). Influence of production method and polymer composition.

Biodegradable particulate systems have been considered as parenteral drug delivery systems. The adsorption of plasma proteins on micro- and nanoparticles is determined by the surface properties and may, in turn, strongly influence the biocompatibility and biodistribution of both carriers. In the present study the influence of the polymer composition and the production method of microspheres on the in vitro plasma protein adsorption were investigated using two-dimensional electrophoresis (2-DE). Microparticles were prepared from poly(l-lactide) (l-PLA), poly(d,l-lactide-co-glycolide) (PLGA), and ABA triblock copolymers containing hydrophilic poly(oxyethylene) (B-blocks) domains connected to hydrophobic polyesters (A-blocks). Two different microencapsulation methods were employed, namely the w/o/w emulsion solvent evaporation method and the spray-drying technique. It could be demonstrated that the polymer composition and, especially, the encapsulation technique, influenced the interactions with plasma proteins significantly. For example, the percentages of several apolipoproteins in the plasma protein adsorption patterns of spray-dried PLGA- and l-PLA-particles were distinctly higher when compared to the adsorption patterns of the particles produced by the w/o/w-technique. Some adsorbed proteins were found to be characteristic or even specific for particles produced by the same method or consisting of identical polymers. Polyvinyl alcohol used as stabilizer in the w/o/w-technique may decisively influence the surface properties relevant for protein adsorption. The plasma protein adsorption on particles composed of ABA copolymers was drastically reduced when compared to microspheres made from pure polyesters. The adsorption patterns of ABA-particles were dominated by albumin. The plasma protein adsorption patterns detected on the different microspheres are likely to affect their in vivo performance as parenteral drug delivery systems.

Adsorption↗
PubMed1998

Nasal delivery of peptides: an in vitro cell culture model for the investigation of transport and metabolism in human nasal epithelium.

We investigated the transport- and metabolism properties of three peptides in monolayers of human nasal epithelial cells. The effective permeability coefficients of thyrotropin-releasing hormone, met-enkephalin and human recombinant insulin were found to be 4.5, 4.4 and 0.4 x 10(-7) cm/s, respectively. The permeability was inversely proportional to the molecular weight and one order of magnitude lower than in excised nasal mucosa of rabbits. The metabolic cleavage of thyrotropin-releasing hormone (TRH) to the free acid by cytosolic prolyl-endopeptidase was also detected in human nasal cell monolayers, suggesting that ca. 10% of the total amount of TRH is transported via a transcellular pathway. Met-enkephalin is a substrate for aminopeptidases, located on the apical membrane of nasal epithelial cells. Metabolites and enzyme activity are comparable with literature data. Our studies demonstrate that not only morphological, but also functional properties of human nasal epithelial cells are preserved under in vitro conditions. Such a cell culture model based on human nasal cells could be beneficial for the characterization of peptide transport on a cellular level and for investigation of the absorption enhancer mechanism. Further studies are necessary, however, to establish correlations between in vitro permeabilities in cell cultures and nasal drug absorption in animals and humans.

Administration, Intranasal↗
PubMed1998

The development of IL-2 conjugated liposomes for therapeutic purposes.

A unique immunoliposome has been developed as a drug delivery vehicle for immunotherapy. Human recombinant interleukin-2 (IL-2) has been chemically coupled to the external surface of small unilamellar vesicles (SUVs) containing methotrexate as a candidate immunosuppresive agent in order to specifically direct the drug-bearing liposome to activated T-cells expressing the high affinity IL-2 receptor. This drug delivery system is designed to deliver an immunosuppressive agent to those cells that actively participate in disorders such as graft rejection without delivering an effective but potentially toxic drug to all cells of the immune system as well as other healthy tissues. IL-2 was chemically modified with succinimidyl 4-[p-maleidophenyl butyrate](SMPB) while the receptor binding domain on IL-2 was protected by monoclonal anti-IL-2 bound to Protein A-Silica Gel. The antibody recognizes the receptor binding domain of the IL-2 molecule. The IL-2 was derivatized with S-succinimidyl-S-thioacetate (SATA) in order to add an acetyl thioester group to the lipid and create the complex. The derivatized lipid (SATA-PE) was then part of the liposome formulation containing DSPC:cholesterol: SATA-PE at a mole ratio of 1.5:1.0:0.26. SMPB-IL-2 was covalently coupled to the external surface of the SUV after deacetylation of the thioester moiety at pH 7.4 in PBS. Liposomes prepared by sonication or extrusion had an average diameter of 46-50 nm. SUV-IL-2 bound to the high affinity IL-2 receptor as measured by competitive binding assays and Scatchard analysis using 111InCl2-loaded liposomes The preparation exhibited a binding constant of 30 pM, consistent with values for free IL-2 cited in the literature. SUV IL-2 could be used as the sole source of IL-2 for the murine CTLL-2 T-cell line or for human mitogen-activated PBLs. The presence of IL-2 coupled to the surface was absolutely required for delivery of the drug to the cell. When methotrexate was encapsulated within the internal aqueous space, receptor-mediated endocytosis led to the inhibition of proliferation due to delivery of MTX to the cytoplasm of the cell. More than 90% of the methotrexate was retained within the liposome during storage over a 24-h period at 4 degrees C. This immunoliposome represents a new class of cell specific immunoliposomes whose entry into the cell is controlled by a cell surface receptor.

Animals↗
PubMed1998

Recombinant human erythropoietin (rhEPO) loaded poly(lactide-co-glycolide) microspheres: influence of the encapsulation technique and polymer purity on microsphere characteristics.

Recombinant human erythropoietin (EPO) and fluorescein isothiocyanate-labelled dextran (FITC-dextran) loaded biodegradable microspheres were prepared from poly(lactide-co-glycolide) (PLG) by a modified spray-drying technique. This microencapsulation method was compared with the water-in-oil-in-water (w/o/w) double-emulsion method. As expected, microsphere morphology, particle size and particle size distribution strongly depended on the production process. The spray-drying method was found to have a number of advantages compared to the w/o/w double-emulsion technique. The content of residual dichloromethane (DCM) in the final product was significantly lower in case of the microspheres prepared by spray-drying. Concerning EPO loaded microspheres, spray-drying yielded higher encapsulation efficiencies. Although the microspheres obtained by spray-drying are subjected to intensive mechanical and thermal stress during the preparation, the amount of aggregates of EPO in PLG microspheres were not increased compared to the w/o/w technique. Depending on the manufacturing method, addition of cyclic DL-lactide dimers (referred to as monomers in the following) affected the in vitro release profiles of EPO and FITC-dextran from PLG microspheres. Using differential scanning calorimetry it was shown that these low molecular weight substances only seem to be present inside the microspheres produced by spray-drying. DL-Lactide significantly reduced the initial burst release of both EPO and FITC-dextran. While the following release period of EPO was not affected by the DL-lactide content, a more linear FITC-dextran release pattern could be achieved. It can be concluded that the spray-drying technique provides a number of advantages compared to the w/o/w method. The modulation of protein release using low molecular weight additives is of particular interest for parenteral depot systems.

Calorimetry, Differential Scanning↗
PubMed1998

Surface-modified biodegradable albumin nano- and microspheres. II: effect of surface charges on in vitro phagocytosis and biodistribution in rats.

The surface charges on biodegradable albumin nanoparticles were introduced by covalent coupling different primary amines to examine their influence on phagocytosis by macrophages under in vitro conditions. Albumin particles with a zeta potential close to zero showed a reduced phagocytic uptake in comparison with charged particles, especially nanoparticles with a positive zeta potential. The phagocytic uptake in the present study was examined using an established cell culture model based on primary mouse peritoneal macrophages and a human hematopoietic monocytic cell line (U-937) treated with phorbol-12-myristic-13-acetate to induce cell differentiation. The influence of opsonins on in vitro phagocytosis experiments was characterized using carriers pre-treated with human serum. In the presence of human serum the phagocytic activity of U-937 cells was found to be similar to primary mouse macrophages without serum. In contrast to peritoneal macrophages, U-937 cells showed no phagocytic activity in the absence of serum. In particular, only the C3b- complement deposition on the particle surface seems to promote the phagocytic process. The in vivo distribution of albumin carriers in rats was investigated using magnetic resonance imaging (MRI). No differences in blood circulation times and organ accumulation between different nanoparticle preparations with positive, neutral and negative surface charges could be observed in rats, suggesting that the in vivo fate of albumin nanoparticles is significantly influenced by factors not reflected in the in vitro cell culture models.

Albumins↗
PubMed1998

Chemo-embolization of experimental liver metastases. Part I: distribution of biodegradable microspheres of different sizes in an animal model for the locoregional therapy.

An experimental in vivo rat model was established to simulate the embolization therapy of non-resectable liver metastases with microparticulate systems. The effects of biodegradable microspheres on a transplanted liver-tumor cell line in rat livers were investigated with respect to particle size. The distribution of fluorescence-labelled microspheres was investigated to characterize the effects of long-term embolization with biodegradable microspheres, and the suitability and relevance of this animal model. Novikoff hepatoma cells were implanted into the central liver lobe of Sprague-Dawley rats. After seven days, four batches of fluorescence-marked microspheres (17 microm, 25 microm, 30 microm, and 40 microm) were administered into the proper hepatic artery. Liver(including the tumor), lung and spleen were isolated and frozen sections and tissue cubes of liver-, border-, and tumor tissue were prepared. The sections were examined by fluorescence microscopy. The cubes were extracted and the fluorescence of the marker quantified. During operation, microspheres smaller than 40 microm did not cause complete embolization. The slides showed the spreading of the smaller particles to the spleen and lung. Only 40 microm particles accumulated in the liver and were rarely detectable in other organs. The extraction showed a high concentration of the 40 microm particles in the border tissue. Apparently they were trapped proximal to the tumor capillary system and therefore showed a high ratio of border/tumor concentration. Microparticles smaller than 40 microm had a border/tumor concentration ratio of less than one and were distributed to the spleen and lung. In conclusion, a mean particle diameter of at least 40 microm is required for embolization. Thus, the model shows similarity to clinical situations in the treatment of human liver tumor and metastases.

Animals↗
PubMed1998

Monitoring microviscosity and microacidity of the albumin microenvironment inside degrading microparticles from poly(lactide-co-glycolide) (PLG) or ABA-triblock polymers containing hydrophobic poly(lactide-co-glycolide) A blocks and hydrophilic poly(ethyleneoxide) B blocks.

PURPOSE: The purpose of this study was to monitor the microenvironment of an encapsulated model protein during the release from biodegradable microparticles (MP) made from three different polymers, namely poly(lactide-co-glycolide) (PLG) and ABA-triblock polymers containing hydrophobic poly(lactide-co-glycolide) A blocks and hydrophilic poly(ethyleneoxide) B blocks with an A:B ratio of 90:10 (ABA1O) and 70:30 (ABA30). METHODS: MP loaded with spin labeled albumin were prepared by a w/o/w technique. The particles were characterized by light scattering and electron microscopy. In vitro release of albumin was determined by size exclusion chromatography. Light microscopic experiments were conducted to visualize water penetration in the matrix. The protein microenvironment inside the degrading microparticles was characterized noninvasively by 2 GHz EPR spectroscopy. RESULTS: Water penetrated rapidly into all MP in the range of few minutes. A burst release was observed for PLG. The release from ABA block-polymers continued for over 14 days despite the rapid solubilization of the protein inside the microparticles. The initial microviscosity of the protein environment inside the ABA particles after exposure to buffer was 2 mm2/s and increased with time. A gradual decrease of the pH to a value of 3.5 was observed within the MP. CONCLUSIONS: The data indicate that the microviscosity and microacidity inside protein loaded microparticles can be studied nondestructively by EPR spectroscopy. Our results clearly demonstrate that ABA-block polymers are superior to PLG allowing a controlled release of proteins from swollen microspheres.

Albumins↗
PubMed1998

Rate control in transdermal beta-estradiol reservoir membrane systems: the role of membrane and adhesive layer.

PURPOSE: The aim of our study was to clarify the kinetic performance of a membrane controlled reservoir system (MCRS) for beta-estradiol (E2) under in vitro conditions by determination of the role of membrane and adhesive layer on E2 flux control. METHODS: E2 and ethanol fluxes across EVA membrane or membrane coated with adhesive from saturated solutions in defined ethanol/PBS mixtures were measured in the symmetric and asymmetric configuration. Physicochemical parameters of the EVA membrane were determined. RESULTS: The E2 flux across the 9% EVA membrane steadily increased with increasing ethanol concentrations in both configurations, due to enhanced uptake of E2 by the polymer and increasing membrane diffusivity. Permeation across the EVA membrane coated with an adhesive layer in symmetric and asymmetric configuration increased up to maximum values of 0.80+/-0.14 micrograms X cm-2 X h-1 and 0.37+/-0.02 micrograms X cm-2 X h-1, respectively, at 62.5% (v/v) ethanol. The fluxes then decreased with further increase in the volume fraction of ethanol due to a dramatically reduced permeability of the adhesive layer. For the asymmetric case, a linear dependence of E2 on the ethanol fluxes was observed. CONCLUSIONS: The E2 flux from MCRS is strictly dependent on reservoir ethanol concentrations, whereas the adhesive layer represents the rate controlling barrier at high ethanol levels (> 70% v/v).

Adhesives↗