Biomedical subjects

T McCreedy

Publications and source records attributed to T McCreedy.

5 recordsLinked to original sources

PubMed2001

Quantitative 3-dimensional profiling of channel networks within transparent lab-on-a-chip microreactors using a digital imaging method.

We have developed a method for the quantitative 3-dimensional profiling of micron sized channel networks within optically transparent "lab-on-a-chip" microreactor devices. The method involves capturing digitised microscope images of the channel network filled with an optically absorbing dye. The microscope is operated in transmission mode using light filtered through a narrow bandpass filter with a maximum transmission wavelength matching the wavelength of the absorbance maximum of the dye solution. Digitised images of a chip filled with solvent and dye solution are analysed pixel by pixel to yield a spatially resolved array of absorbance values. This array is then converted to optical path length values using the Beer-Lambert law, thereby providing the 3D profile of the channel network. The method is capable of measuring channel depths from 10 to 500 microm (and probably even smaller depths) with an accuracy of a few percent. Lateral spatial resolution of less than 1 microm is achievable. It has been established that distortion of the measured profiles resulting from a mismatch in refractive index between the dye solution and the glass of the microreactors is insignificant. The method has been successfully used here to investigate the effects of thermal bonding and etch time on channel profiles. The technique provides a convenient, accurate and non-destructive method required to determine channel profiles; information which is essential to enable optimisation of the operating characteristics of microreactor devices for particular applications.

Journal Article↗

PubMed2001

Tris(2,2'-bipyridine)ruthenium(II) electrogenerated chemiluminescence of alkaloid type drugs with solid phase extraction sample preparation.

An electrogenerated chemiluminescence (ECL) method for the determination of pethidine, atropine, homatropine and cocaine is described. The optimum conditions were found to be similar for all of these compounds although the ECL emission intensity for cocaine was an order of magnitude lower than for pethidine due to their different chemical structures. Linear calibrations were obtained for all the compounds at pH 10 in borate buffer (0.05 mol l-1) at 1.3 V. Limits of detection of 6.8 x 10(-8), 2.2 x 10(-7), 3.2 x 10(-7) and 6.5 x 10(-7) mol l-1, respectively, were achieved for pethidine, atropine, homatropine and cocaine in standard solutions. Solid-phase extraction was used to separate the drugs from their matrix and the method was applied to the determination of spiked urine samples. The limits of quantitation for pethidine, atropine, homatropine and cocaine in urine were 1.0 x 10(-6), 2.0 x 10(-6), 2.0 x 10(-6) and 4.0 x 10(-6) mol l-1, respectively, with recoveries of between 90 and 110%.

Alkaloids↗

PubMed2001

Microfabricated reactors for on-chip heterogeneous catalysis.

Microfabricated devices constructed from glass and polydimethylsiloxane with integral heaters are described, which can be used for heterogeneous catalysis reactions. Sulfated zirconia is used as the catalyst in an open channel reactor, with either a syringe pump or electroosmotic flow being used to deliver the reactants. The results clearly demonstrate that very high conversion efficiencies are possible, however, the thermodynamics of the reactions are the same as in bulk systems. Ethanol and hexanol are dehydrated to ethene and hexene, respectively, with conversion efficiencies approaching 100%, and the esterification of ethanol is investigated. Yields of approximately 30% ethyl acetate are obtained by gas chromatographic analysis. This is the first time such a method for fabricating a catalyst micro reactor has been reported, yet it demonstrates sufficient robustness and resistance to leakage. The use of electroosmotic flow in a heated catalyst reactor is a significant advancement in reactor design.

Journal Article↗

PubMed2001

Electric field-induced mobilisation of multiphase solution systems based on the nitration of benzene in a micro reactor.

This paper describes the electric field-induced flow characteristics of multiphase solutions in a micro reactor device using the nitration of benzene as a model process. Photolithographic and wet etching techniques were used to fabricate the micro reactor (channels, 200 microns id, 100 microns deep) in a borosilicate glass substrate. The results focus specifically on the flow parameters of reagents/reactants (i.e., voltage, solution concentration and pH ranges and current-voltage relationships) used in this study. The benzene was introduced and mobilised by electroosmotic flow (EOF), as a microemulsion using an appropriate surfactant (sodium dodecyl sulfate), whilst the nitronium ions, produced in situ from mixed H2SO4-HNO3 (the nitrating agent), underwent electrophoretic-induced (electrokinetic) mobility. A co-surfactant, butan-1-ol, was used owing to (a) its relative solubility in the aqueous surfactant solution, (b) its ability to aid the solubilization of benzene, (c) the provision of a water-rich (oil-in-water) rather than oil-rich (water-in-oil) microemulsion system and (d) its lack of significant adverse effects on the EOF. The optimum conditions used for the nitration of benzene within the micro reactor were a run of the microemulsion as main reagent stream, then three 30 s segmented injections of mixed acid, with a 5 s push of the microemulsion into the system after each injection, and then a 60 s stopped-flow reaction time before driving reaction product segments to a collection reservoir.

Journal Article↗

PubMed2001

Preliminary studies into the direct interfacing of a microreactor to a gas chromatographic instrument.

The paper reports on a preliminary study into the coupling of a microreactor to a GC-FID, using a standard GC needle as the interface between the microreactor and the injection port of a conventional GC. Using the injection needle as the ground electrode, electroosmotic flow was used to control the injection of reagent/sample into the GC. Photolithographic and wet etching techniques were used to fabricate the microreactor (channels 200 microns id, 100 microns deep) in a borosilicate glass substrate. The results of the effects of voltage and injection times on the response signal are presented. The critical obstacles to overcome were the backpressure posed by the carrier gas disrupting the liquid flow in the channels and reservoirs of the microreactor and the need to thermally insulate the microreactor, to prevent evaporation of solvent and reagents from the device.

Journal Article↗