PubMed Health⌕ Search

Biomedical subjects

T Tyliszczak

Publications and source records attributed to T Tyliszczak.

12 recordsLinked to original sources

Magnetic vortex core reversal by excitation with short bursts of an alternating field.

The vortex state, characterized by a curling magnetization, is one of the equilibrium configurations of soft magnetic materials and occurs in thin ferromagnetic square and disk-shaped elements of micrometre size and below. The interplay between the magnetostatic and the exchange energy favours an in-plane, closed flux domain structure. This curling magnetization turns out of the plane at the centre of the vortex structure, in an area with a radius of about 10 nanometres--the vortex core. The vortex state has a specific excitation mode: the in-plane gyration of the vortex structure about its equilibrium position. The sense of gyration is determined by the vortex core polarization. Here we report on the controlled manipulation of the vortex core polarization by excitation with small bursts of an alternating magnetic field. The vortex motion was imaged by time-resolved scanning transmission X-ray microscopy. We demonstrate that the sense of gyration of the vortex structure can be reversed by applying short bursts of the sinusoidal excitation field with amplitude of about 1.5 mT. This reversal unambiguously indicates a switching of the out-of-plane core polarization. The observed switching mechanism, which can be understood in the framework of micromagnetic theory, gives insights into basic magnetization dynamics and their possible application in data storage.

Journal Article↗

Time-resolved imaging of spin transfer switching: beyond the macrospin concept.

Time-resolved images of the magnetization switching process in a spin transfer structure, obtained by ultrafast x-ray microscopy, reveal the limitations of the macrospin model. Instead of a coherent magnetization reversal, we observe switching by lateral motion of a magnetic vortex across a nanoscale element. Our measurements reveal the fundamental roles played independently by the torques due to charge and spin currents in breaking the magnetic symmetry on picosecond time scales.

Journal Article↗

Interferometer-controlled scanning transmission X-ray microscopes at the Advanced Light Source.

Two new soft X-ray scanning transmission microscopes located at the Advanced Light Source (ALS) have been designed, built and commissioned. Interferometer control implemented in both microscopes allows the precise measurement of the transverse position of the zone plate relative to the sample. Long-term positional stability and compensation for transverse displacement during translations of the zone plate have been achieved. The interferometer also provides low-distortion orthogonal x, y imaging. Two different control systems have been developed: a digital control system using standard VXI components at beamline 7.0, and a custom feedback system based on PC AT boards at beamline 5.3.2. Both microscopes are diffraction limited with the resolution set by the quality of the zone plates. Periodic features with 30 nm half period can be resolved with a zone plate that has a 40 nm outermost zone width. One microscope is operating at an undulator beamline (7.0), while the other is operating at a novel dedicated bending-magnet beamline (5.3.2), which is designed specifically to illuminate the microscope. The undulator beamline provides count rates of the order of tens of MHz at high-energy resolution with photon energies of up to about 1000 eV. Although the brightness of a bending-magnet source is about four orders of magnitude smaller than that of an undulator source, photon statistics limited operation with intensities in excess of 3 MHz has been achieved at high energy resolution and high spatial resolution. The design and performance of these microscopes are described.

Journal Article↗

Optimization of scanning transmission X-ray microscopy for the identification and quantitation of reinforcing particles in polyurethanes.

The morphology, size distributions, spatial distributions, and quantitative chemical compositions of co-polymer polyol-reinforcing particles in a polyurethane have been investigated with scanning transmission X-ray microscopy (STXM). A detailed discussion of microscope operating procedures is presented and ways to avoid potential artifacts are discussed. Images at selected photon energies in the C 1s, N 1s and O 1s regions allow unambiguous identification of styrene-acrylonitrile-based (SAN) copolymer and polyisocyanate polyaddition product-based (PIPA) reinforcing particles down to particle sizes at the limit of the spatial resolution (50 nm). Quantitative analysis of the chemical composition of individual reinforcing particles is achieved by fitting C 1s spectra to linear combinations of reference spectra. Regression analyses of sequences of images recorded through the chemically sensitive ranges of the C 1s, N 1s and O 1s spectra are used to generate quantitative compositional maps, which provide a fast and effective means of investigating compositional distributions over a large number of reinforcing particles. The size distribution of all particles determined by STXM is shown to be similar to that determined by TEM. The size distributions of each type of reinforcing particle, which differ considerably, were obtained by analysis of STXM images at chemically selective energies.

Microscopy, Electron, Scanning↗