Biomedical subjects

Victor H Barocas

Publications and source records attributed to Victor H Barocas.

16 recordsLinked to original sources

PubMed2006

Using channel depth to isolate and control flow in a micro free-flow electrophoresis device.

A multiple-depth micro free-flow electrophoresis chip (mu-FFE) has been fabricated with a 20-microm-deep separation channel and 78-microm-deep electrode channels. Due to the difference in channel heights, the linear velocity of buffer in the electrode channels is approximately 15 times that of the buffer in the separation channel. Previous mu-FFE devices have been limited by electrolysis product formation at the electrodes. These electrolysis products, manifested as bubbles, decreased the electric field and disrupted the buffer flow profile, limiting performance and preventing continuous operation. Using channel depth to control buffer flow over the electrodes and in the separation channel effectively removes electrolysis products, allowing continuous operation. The linear velocities in the channels were confirmed using particle velocimetry and compared well with values predicted using lubrication theory. A separation potential of 645 V could be applied before significant Joule heating was observed. This corresponded to an electric field of 586 V/cm in the separation channel, a 4-fold increase over our previous design. A separation of fluorescent standards was demonstrated using the new mu-FFE device. Resolution increased by a factor of 1.3 over our previous design, even when operated under similar conditions, suggesting that effective removal of electrolysis products is more important than originally thought.

Electrodes↗

PubMed2006

Accommodative microfluctuations and iris contour.

Mechanical interaction between aqueous humor, iris, and intraocular structures can alter the iris profile from its normal curvature. In particular, significant changes to the iris profile occur during accommodation as the anterior lens movement forces the iris into greater posterior bowing. We extended a previous mathematical model of the anterior segment and investigated the response of this coupled fluid-solid system due to accommodative microfluctuations. The results showed that the system response exhibited the same waveform as the stimulus for small-amplitude microfluctuations generally associated with the high-frequency component. Low-frequency microfluctuations with relatively larger amplitudes elicited a response different from the stimulus, indicating that the forces generated by the lens movement significantly affected the aqueous-iris mechanical interaction.

Accommodation, Ocular↗

PubMed2006

Effects of freezing and cryopreservation on the mechanical properties of arteries.

Cryoplasty, a freezing therapy, is being used for the treatment of restenosis in peripheral arteries. In addition, cryo-preserved arteries are increasingly used in vascular grafts. While studies are being performed to establish the efficacy of such treatments, very little is known about the postcryosurgical or postcryo-preservation changes in mechanical properties of the arteries. Few studies have examined the effect of freezing in the absence of cryoprotective agents (CPAs), and the several studies done in the presence of CPAs have given mixed results. To examine this issue further, we froze pig femoral arteries in a controlled rate freezer, using an aluminum probe, both in the presence at (-80 degrees C to 1 degrees C/min) and absence (at -20 degrees C for 2 or 5 mins) of CPA and Fetal bovine serum (FBS). Following freezing, artery samples were subjected to uniaxial tensile testing. The weights of the tissue were measured before and after freezing. Our results suggest that freezing does have an effect on stress-strain properties, particularly in the low stress region corresponding to physiological conditions. The mechanisms of this change in mechanical properties may include the loss of smooth muscle cell viability, damage to extra cellular matrix (ECM), bulk redistribution of water, or changes in alignment caused by ice crystal growth. In the case of samples frozen in the absence of CPA or FBS, the results indicated a drastic reduction in weight of the tissue suggesting the importance of bulk water redistribution as one underlying mechanism. To further examine potential mechanisms, we subjected cryopreserved vessels to the same uniaxial tests. The extent of changes in mechanical properties and bulk water redistribution was greatly attenuated; reinforcing that water movement might play a role in the changes observed with freezing.

Adaptation, Physiological↗

PubMed2006

Biomechanical and microstructural characteristics of a collagen film-based corneal stroma equivalent.

The growth in refractive surgeries and corneal replacements has fueled interest in the development of a tissue-engineered cornea. This study characterizes the microstructure and biomechanical properties of film-based corneal stroma equivalents over time in culture. The increased collagen density in the films was hypothesized to result in improved mechanical properties both initially and over time. The microstructure of the film-based stromal equivalent was examined using atomic force microscopy and scanning electron microscopy; the mechanical properties, relaxed modulus, and ultimate tensile strength were quantified using uniaxial tensile testing. The dense, film-based stromal equivalent had a lamellae-like microstructure, which was notably different than the porous structure of sponges used previously. Seeded human corneal stromal fibroblasts remained on the surface of the film rather than migrating into the film and produced fibers of extracellular matrix with diameters of 35-75 nm. After an initial decrease during hydration, the relaxed modulus and ultimate tensile strength for fully hydrated collagen films were 0.4 +/- 0.2 MPa and 0.3 +/- 0.1 MPa, respectively. The mechanical properties of cell-seeded films mimicked those of control films. While further studies are needed to quantify the optical properties, the dense, lamellae-like structure of collagen films is a feasible scaffold for the development of tissue-engineered stroma.

Animals↗

PubMed2006

Affine versus non-affine fibril kinematics in collagen networks: theoretical studies of network behavior.

The microstructure of tissues and tissue equivalents (TEs) plays a critical role in determining the mechanical properties thereof. One of the key challenges in constitutive modeling of TEs is incorporating the kinematics at both the macroscopic and the microscopic scale. Models of fibrous microstructure commonly assume fibrils to move homogeneously, that is affine with the macroscopic deformation. While intuitive for situations of fibril-matrix load transfer, the relevance of the affine assumption is less clear when primary load transfer is from fibril to fibril. The microstructure of TEs is a hydrated network of collagen fibrils, making its microstructural kinematics an open question. Numerical simulation of uniaxial extensile behavior in planar TE networks was performed with fibril kinematics dictated by the network model and by the affine model. The average fibril orientation evolved similarly with strain for both models. The individual fibril kinematics, however, were markedly different. There was no correlation between fibril strain and orientation in the network model, and fibril strains were contained by extensive reorientation. As a result, the macroscopic stress given by the network model was roughly threefold lower than the affine model. Also, the network model showed a toe region, where fibril reorientation precluded the development of significant fibril strain. We conclude that network fibril kinematics are not governed by affine principles, an important consideration in the understanding of tissue and TE mechanics, especially when load bearing is primarily by an interconnected fibril network.

Anisotropy↗

PubMed2005

A cryoinjury model using engineered tissue equivalents for cryosurgical applications.

Cryosurgery is emerging as a promising treatment modality for various cancers, but there are still challenges to be addressed to improve its efficacy. Two primary challenges are determining thermal injury thresholds for various types of cell/tissue, and understanding of the mechanisms of freezing induced cell/tissue injury within a cryolesion. To address these challenges, various model systems ranging from cell suspensions to three-dimensional in vivo tissues have been developed and used. However, these models are either oversimplifications of in vivo tissues or difficult to control and extract precise experimental conditions from. Therefore, a more readily controllable model system with tissue-like characteristics is needed. In this study, a cryoinjury model was developed using tissue engineering technology, and the capabilities of the model were demonstrated. Engineered tissue equivalents (TEs) were constructed by seeding and culturing cells in a type I collagen matrix. Two different cell lines were used in this study, AT-1 rat prostate tumor cells and LNCaP human prostate cancer cells. The constructed TEs underwent a freeze/thaw cycle imitating in vivo cryosurgery. Thermal conditions within TEs during freeze/thaw cycles were characterized, and the responses of TEs to these thermal conditions including freezing induced cellular injury and extracellular matrix damage were investigated at three different time points. The results illustrate the feasibility to establish thermal thresholds of cryoinjury for different cell/tissue types using the presently developed model, and its potential capabilities to study cell death mechanisms, cell proliferation or migration, and extracellular matrix structural damage after a freeze/thaw cycle.

Animals↗

PubMed2005

Modeling and characterization of a valved glaucoma drainage device with implications for enhanced therapeutic efficacy.

We report on modeling and bench test results targeted at better understanding of valved glaucoma drainage devices (GDDs), a common current surgical treatment for glaucoma. A simple equivalent circuit is described to model fluid mechanical behavior of the aqueous humor in an eye with glaucoma, both before and after implantation of a valved GDD. Finite element method simulations (FEM), based on the lubrication-von Kármán model, are then performed to analyze the valve's mechanical and fluidic performance. Using nanoporous membranes to mimic the in vivo fibrous capsule, we have developed a microfluidic bench test to simulate the aqueous humor flow and the post-implantation fibrous tissue encapsulation around the GDD back plate. Our numerical and bench test results show that, contrary to the prevailing belief, the valve significantly contributes to the total pressure drop even after fibrous capsule formation. Furthermore, we show that bypassing the valve through a simple polyimide tube insertion will dramatically lower the intraocular pressure (IOP) after fibrous capsule formation. This may offer a new treatment option in some patients with advanced glaucoma.

Computer Simulation↗

PubMed2005

Thin-film coupled fluid-solid analysis of flow through the Ahmed glaucoma drainage device.

The Ahmed glaucoma valve (AGV) is a popular glaucoma drainage device, allowing maintenance of normal intraocular pressure in patients with reduced trabecular outflow facility. The uniquely attractive feature of the AGV, in contrast to other available drainage devices, is its variable resistance in response to changes in flow rate. As a result of this variable resistance, the AGV maintains a pressure drop between 7 and 12 mm Hg for a wide range of aqueous humor flow rates. In this paper, we demonstrate that the nonlinear behavior of the AGV is a direct result of the flexibility of the valve material. Due to the thin geometry of the system, the leaflets of the AGV were modeled using the von Kármán plate theory coupled to a Reynolds lubrication theory model of the aqueous humor flow through the valve. The resulting two-dimensional coupled steady-state partial differential equation system was solved by the finite element method. The Poisson's ratio of the valve was set to 0.45, and the modulus was regressed to experimental data, giving a best-fit value 4.2 MPa. Simulation results compared favorably with previous experimental studies and our own pressure-drop/flow-rate data. For an in vitro flow of 1.6 microL/min, we calculated a pressure drop of 5.8 mm Hg and measured a pressure drop of 5.2 +/- 0.4 mm Hg. As flow rate was increased, pressure drop rose in a strongly sublinear fashion, with a flow rate of 20 microL/min giving a predicted pressure drop of only 10.9 mm Hg and a measured pressure drop of 10.5 +/- 1.1 mm Hg. The AGV model was then applied to simulate in vivo conditions. For an aqueous humor flow rate of 1.5-3.0 microL/min, the calculated pressure drops were 5.3 and 6.3 mm Hg.

Aqueous Humor↗

PubMed2004

Application of the lag-after-pulsed-separation (LAPS) flow meter to different protein solutions.

A lag after pulsed separation (LAPS) meter was previously developed to measure flow rates of protein solutions. The LAPS meter operates on the time-of-flight principle. An upstream event (electrophoretic concentration of the particles in one section of the device) is detected downstream (by change in ac resistance). The time lag between the event and its detection is inversely proportional to the fluid flow rate. We demonstrate the ability of the LAPS meter to measure the flow rate of solutions containing one or more charged biomacromolecules or particles. A prototype of the LAPS meter was used to measure flow rates of solutions of model proteins [bovine serum albumin (BSA), lysozyme and hemoglobin] and mixtures of BSA and lysozyme. Flow rates of 10-50 microl min(-1)(average velocities of 0.24-1.2 mm s(-1)) were measured. When a single ac measurement was used, the results were solution-dependent, which we attribute to the interface between the protein solution and the ac electrodes. A differential mode, in which the signal from a positive and a negative dc pulse were subtracted from each other, eliminated interfacial effects and led to a single universal (solution-independent) calibration curve. The LAPS meter can be used as a non-invasive, no-moving-parts flow sensor in any microfluidic system (such as drug delivery devices or micro-reactor arrays) where one needs to measure the flow rate of a solution or a suspension containing charged species such as proteins or cells.

Animals↗

PubMed2004

Mechanical and cellular changes during compaction of a collagen-sponge-based corneal stromal equivalent.

The need for corneas suitable for transplantation, combined with the decreasing supply, has fueled interest in the development of a corneal replacement. In this study, a collagen-sponge-based stromal equivalent, consisting of human corneal fibroblasts cultured on a type I collagen sponge, was maintained in culture for up to 21 days and characterized with respect to mechanical properties and cellular behavior. The Young's modulus of the stromal equivalent varied from 95 to 370 Pa, and its permeability varied from 5.3 x 10(-8) - 4.2 x 10(-7) m4 N(-1) s(-1). The greatest changes occurred during the first few days in culture, but the mechanical properties continued to change during the entire 21 days. Cell traction stress, determined from sponge compaction and DNA count, decreased during the compaction process with the maximum traction value the initial value of 6.6 +/- 2.9 x 10(-3) Pacm3 cell(-1). Microarray data showed that the expression level of fibronectin, decorin sulfate, collagenase, and gelatinase A was upregulated at day 14 in the sponge. This suggested that the repair fibroblast phenotype was being expressed by the fibroblasts. Additional analysis suggested that a subpopulation of cells expressed the myofibroblast phenotype.

Biocompatible Materials↗

PubMed2004

Active iris mechanics and pupillary block: steady-state analysis and comparison with anatomical risk factors.

Primary angle-closure glaucoma arises when the iris physically obstructs outflow of aqueous humor, increasing the intraocular pressure and damaging the optic nerve. Pupillary block, the predominant mechanism for angle closure, is believed to be driven by mechanical interaction between the aqueous humor and the iris. We performed steady-state simulations of this coupled fluid-solid system, including an active sphincter to control pupil constriction. Model results compared favorably against Mapstone's pupil-blocking force analysis. We also evaluated anatomical risk factors and quantified their contributions to pupillary block and angle closure. The results showed that greater lens curvature and shorter iris-zonule distance contribute significantly to pupillary block and the associated narrowing of the angle. Surprisingly, the model predicted that maximum pupillary block and angle closure occur at the minimum pupil dilation, contradicting the clinical observation that angle closure is most severe in dark conditions. This discrepancy suggests the involvement of one or more phenomena not captured by our current model.

Animals↗

PubMed2004

Microstructural mechanics of collagen gels in confined compression: poroelasticity, viscoelasticity, and collapse.

BACKGROUND: Collagen gels are important as platforms for in vitro study of cell behavior and as prototypical bioartificial tissues, but their mechanical behavior, particularly on the microscopic scale, is still poorly understood. METHOD OF APPROACH: Collagen gels were studied in step (10% strain in 0.05 s) and ramp (0.1%/s strain rate for 100 s) confined compression. Real-time birefringence mapping gave the local collagen concentration and orientation along with piston stress. Variations in the retardation allowed material-point tracking and qualitative determination of the strain distribution. RESULTS: Ramp tests showed classical poroelastic behavior: compression near the piston and relaxation to a uniform state. Step tests, however, showed an irreversibly collapsed region near the piston. CONCLUSIONS: Our results suggest that interstitial flow and fibril bending at crosslinks are the dominant mechanical processes during compression, and that fibril bending is reversible before collapse.

Animals↗

PubMed2003

Temporal variations in cell migration and traction during fibroblast-mediated gel compaction.

Current models used in our laboratory to assess the migration and traction of a population of cells within biopolymer gels are extended to investigate temporal changes in these parameters during compaction of mechanically constrained gels. The random cell migration coefficient, micro (t) is calculated using a windowing technique by regressing the mean-squared displacement of cells tracked at high magnification in three dimensions with a generalized least squares algorithm for a subset of experimental time intervals, and then shifting the window interval-by-interval until all time points are analyzed. The cell traction parameter, tau(0)(t), is determined by optimizing the solution of our anisotropic biphasic theory to tissue equivalent compaction. The windowing technique captured simulated sinusoidal and step changes in cell migration superposed on a persistent random walk in simulated cell movement. The optimization software captured simulated time dependence of compaction on cell spreading. Employment of these techniques on experimental data using rat dermal fibroblasts (RDFs) and human foreskin fibroblasts (HFFs) demonstrated that these cells exhibit different migration-traction relationships. Rat dermal fibroblast migration was negatively correlated to traction, suggesting migration was not the driving force for compaction with these cells, whereas human foreskin fibroblast migration was positively correlated to traction.

Algorithms↗

PubMed2003

Computer simulation of convective and diffusive transport of controlled-release drugs in the vitreous humor.

PURPOSE: Biodistribution of drugs in the eye is central to the efficacy of pharmaceutical ocular therapies. Of particular interest to us is the effect of intravitreal transport on distribution of controlled-released drugs within the vitreous. METHODS: A computer model was developed to describe the three-dimensional convective-diffusive transport of drug released from an intravitreal controlled release source. Unlike previous studies, this work includes flow of aqueous from the anterior to the posterior of the vitreous. The release profile was based on in vitro release of gentamicin from poly(L-lactic acid) microspheres into vitreous. RESULTS: For small drugs, convection plays a small role, but for large (slower diffusing) drugs, convection becomes more important. For the cases studied, the predicted ratio of drug reaching the retina to drug cleared by the aqueous humor was 2.4 for a small molecule but 13 for a large molecule. Transport in neonatal mouse eye, in contrast, was dominated by diffusion, and the ratio decreased to 0.39. CONCLUSIONS: The interaction among convection, diffusion, and geometry causes significant differences in biodistribution between large and small molecules or across species. These differences should be considered in the design of delivery strategies or animal studies.

Animals↗

PubMed2002

A boussinesq model of natural convection in the human eye and the formation of Krukenberg's spindle.

The cornea of the human eye is cooled by the surrounding air and by evaporation of the tear film. The temperature difference between the cornea and the iris (at core body temperature) causes circulation of the aqueous humor in the anterior chamber of the eye. Others have suggested that the circulation pattern governs the shape of the Krukenberg spindle, a distinctive vertical band of pigment on the posterior cornea surface in some pathologies. We modeled aqueous humor flow the human eye, treating the humor as a Boussinesq fluid and setting the corneal temperature based on infrared surface temperature measurements. The model predicts convection currents in the anterior chamber with velocities comparable to those resulting from forced flow through the gap between the iris and lens. When paths of pigment particles are calculated based on the predicted flow field, the particles circulate throughout the anterior chamber but tend to be near the vertical centerline of the eye for a greatest period of time. Further, the particles are usually in close proximity to the cornea only when they are near the vertical centerline. We conclude that the convective flow pattern of aqueous humor is consistent with a vertical pigment spindle.

Aqueous Humor↗

PubMed2002

Computational evaluation of the role of accommodation in pigmentary glaucoma.

PURPOSE: Accommodation has been proposed as the cause of the bowing of the posterior iris that occurs in eyes with pigmentary dispersion syndrome. A mathematical model of the anterior eye is needed to explore the elastohydrodynamic effects of accommodation on both the aqueous humor dynamics and the contour of the iris. METHODS: A mathematical model of the coupled aqueous humor-iris system was used to predict the effects of accommodation on the iris position and pressure distribution in the aqueous humor. RESULTS: The mathematical model predicts that accommodation produces a pressure reversal--the anterior chamber pressure being higher than the posterior chamber--and iris movement into a more concave configuration. Total time for accommodation, iris modulus, iris attachment point, and trabecular meshwork permeability all had little or no effect on the iris contour and pressure change. The amount of accommodation, however, had a dramatic effect on both the amount of iris curvature and especially the pressure reversal. For accommodation resulting in a 0.6-mm change in anterior chamber depth, the pressure in the anterior chamber was more than 1.0 mm Hg higher than that in the posterior chamber, compared with a pressure difference of less than 0.1 mm Hg for accommodation resulting in a 0.2-mm change in anterior chamber depth. CONCLUSIONS: The results confirm that accommodation produces bowing of the posterior iris and the magnitude of the bowing is a strong function of the amount of accommodation.

Accommodation, Ocular↗