PubMed Health⌕ Search

Biomedical subjects

W W Nagy

Publications and source records attributed to W W Nagy.

14 recordsLinked to original sources

The effect of thermocycling on the fracture toughness and hardness of core buildup materials.

STATEMENT OF PROBLEM: Thermocycling has been shown to cause surface degradation of many dental materials, but its effect on the fracture toughness and hardness of direct core buildup materials is unknown. PURPOSE: This study was designed to determine the effect of thermocycling on the fracture toughness and hardness of 5 core buildup materials. MATERIAL AND METHODS: Fifteen specimens were prepared from each of the following materials: Fluorocore, VariGlass VLC, Valiant PhD, Vitremer, and Chelon-Silver. American Standard for Testing Materials guidelines for single-edge notch, bar-shaped specimens were used. Ten specimens of each material were thermocycled for 2000 cycles; the other 5 specimens were not thermocycled. All specimens were subjected to 3-point bending in a universal testing machine. The load at fracture was recorded, and the fracture toughness (K(IC)) was calculated. Barcol hardness values were also determined. Data were analyzed with 1-way analysis of variance and compared with the Tukey multiple range test (P<.05). Pearson's correlation coefficient was also calculated to measure the association between fracture toughness and hardness. RESULTS: Fluorocore had the highest thermocycled mean K(IC) and Valiant PhD the highest non-thermocycled K(IC). Chelon-Silver demonstrated the lowest mean K(IC) both before and after thermocycling. One-way analysis of variance demonstrated significant differences between conditions, and the Tukey test showed significant differences (P<.05) between materials for both conditions. Most specimens also showed significant hardness differences between conditions. Pearson's correlation coefficient indicated only a mild-to-moderate correlation between hardness and fracture toughness. CONCLUSION: Within the limitations of this study, the thermocycling process negatively affected the fracture toughness and hardness of the core buildup materials tested.

Acrylic Resins↗

The qualitative effects of various types of hygiene instrumentation on commercially pure titanium and titanium alloy implant abutments: an in vitro and scanning electron microscope study.

STATEMENT OF PROBLEM: Implant survival depends on proper and timely oral hygiene maintenance, and a wide variety of oral prophylaxis procedures have been recommended and used on implant abutments. PURPOSE: This in vitro study compared the surface quality of both commercially pure titanium and titanium-alloy implant abutments, subjected to various hygiene methods and instruments with a standardized, clinically applicable scaling force. MATERIAL AND METHODS: Commercially pure titanium and titanium-alloy abutments were exposed to five oral hygiene methods; a gold-alloy-tipped scaler, a high-grade resin scaler, a graphite-reinforced scaler, an air-powder abrasive system, and a rubber cup with tin oxide slurry. A customized test device that simulated the scaling motion and allowed the application of a standard load at the tip of the scaler was used. Scanning electron photomicrographs (x200) of the pretreatment and treated surfaces were obtained and compared qualitatively. RESULTS AND CONCLUSIONS: No significant surface alteration was produced by the air abrasive system. All other hygiene methods either created significant surface alterations, left residual particles on the abutment surfaces, or both.

Acrylic Resins↗

Protection of recent extraction sites when fabricating immediate acrylic interim fixed restorations.

Protection of all soft tissues is an early and integral component of the total treatment plan involving any dental restoration. A procedure is presented to provide protection of recent extraction sites by using adhesive Burlew foil when making an immediate fixed restoration. The foil provides protection, at the extraction site, from both mechanical and chemical irritation.

Acrylic Resins↗

Removable partial denture framework try-in.

Removable partial denture frameworks must fit accurately to function properly and not cause injury to remaining teeth or soft tissue. This article presents a logical method and rationale for seating a removable partial denture framework and a review of several disclosing media used in the try-in procedure.

Acrylic Resins↗

A simplified matrix for making direct cores.

This article describes the use of a pharmaceutical gelatin capsule as a matrix for making various posted and nonposted crown substructures. The procedure used for a cast post and core using this matrix is outlined.

Capsules↗

Fabrication of an obstructive sleep apnea prosthesis.

Obstructive sleep apnea, a sleep disorder, is becoming more prevalent and requires prompt and effective treatment by the dental and medical specialties. Conservative treatment modalities (ie, intraoral devices that prevent or minimize airway obstruction by the tongue) are recommended for treating mild to moderate forms of OSA. This article describes a simplified technique for fabricating an intraoral OSA prosthesis.

Humans↗

Saw modification for underside die cutting.

A simple modification of a standard laboratory saw and the work bench surface enhances the saw's overall usefulness for sectioning casts. When using these modifications, the operator has a clear view of the preparation margin and the saw blade at all times, thereby permitting accurate, controlled cuts to be made from the underside of a removable pinned die section.

Denture Design↗

The versatile air abrasive blaster.

The air-abrasive blaster has become an indispensable tool in the prosthodontic laboratory. New uses are discovered daily. A number of them are described in this article.

Dental Polishing↗

Effects of sterilization procedures on the cutting efficiency of stainless steel and carbon steel Gates Glidden drills.

One-hundred fifty carbon steel Gates Glidden drills were compared with 150 stainless steel Gates Glidden drills before and after sterilization in an autoclave, salt beads, dry heat, or 2% alkaline glutaraldehyde. Cutting efficiency and separation rates of the drills were evaluated. Stainless steel #1 and 2 Gates Glidden drills resisted separation and maintained their cutting efficiency statistically better than the carbon steel #1 and 2 Gates Glidden drills after one sterilization cycle in an autoclave, salt bead sterilizer, or dry heat oven. Glutaraldehyde did not effect either type of drill.

Corrosion↗