Biomedical subjects

Wei-Yin Liao

Publications and source records attributed to Wei-Yin Liao.

4 recordsLinked to original sources

PubMed2006

Development and characterization of an all-solid-state potentiometric biosensor array microfluidic device for multiple ion analysis.

A microfluidic device with an all-solid-state potentiometric biosensor array was developed using microfabrication technology. The sensor array included a pH indicator, and potassium and calcium ion-selective microelectrodes. The pH indicator was an iridium oxide thin film modified platinum microelectrode and the iridium oxide was deposited by an electrochemical method. The potassium and calcium ion-selective microelectrodes were platinum coated with silicon rubber based ion-selective membranes with respectively potassium (valinomycin) and calcium (ETH 1001) ionophores. The detection system was integrated with a micro-pneumatic pump which can continuously drive fluids into the microchannel through sensors at flow rates ranging from 52.4 microl min(-1) to 7.67 microl min(-1). The sensor array microfluidic device showed near-Nernstian responses with slopes of 62.62 mV +/- 2.5 mV pH(-1), 53.76 mV +/- 3 mV -log[K+](-1) and 25.77 mV +/- 2 mV -log[Ca2+](-1) at 25 degrees C +/- 5 degrees C, and a linear response within the pH range of 2-10, with potassium and calcium concentrations between 0.1 M and 10(-6) M. In this study the device provided a convenient way to measure the concentration of hydrogen, potassium and calcium ions, which are important physiological parameters.

Biosensing Techniques↗

PubMed2006

Fabrication of a planar-form screen-printed solid electrolyte modified Ag/AgCl reference electrode for application in a potentiometric biosensor.

This study features the fabrication of a planar-form, solid electrolyte modified, (PSEM) Ag/AgCl reference electrode using a screen-printing method. The PSEM Ag/AgCl reference electrode uses agar gel as the inner electrolyte and chloroprene rubber for the liquid junction and insulator. These common low-cost materials and the simple fabrication processes involved render the proposed reference electrode an ideal candidate for cost-efficient mass production. It is shown that the developed reference electrode is insensitive to most of the physiologically important ionic species, including Na+, K+, Li+, Ca2+, NH4+, and Cl-, under continuous measurement conditions. Moreover, as with conventional commercial reference electrodes, the proposed reference electrode exhibits a reversible response, which is maintained until the agar gel dries out. The PSEM Ag/AgCl reference electrode is integrated with an iridium oxide modified Pt-based pH indicator electrode to form a chip-type pH biosensor. The performance of this biosensor is consistent with that obtained from a pH meter based on a macroscopic commercial Ag/AgCl reference electrode. The experimental results confirm that the proposed biosensor is capable of providing precise pH measurements of various real samples. Accordingly, the PSEM Ag/AgCl reference electrode presented in this study provides a viable alternative to the macroscopic Ag/AgCl reference electrode used in many conventional chip-based pH sensors.

Biosensing Techniques↗

PubMed2005

Microfluidic pH-sensing chips integrated with pneumatic fluid-control devices.

This paper presents a microfluidic chip capable of performing precise continuous pH measurements in an automatic mode. The chip is fabricated using micro-electro-mechanical-systems (MEMS)-based techniques and incorporates polydimethylsiloxane (PDMS) microstructures, pH-sensing electrodes and pneumatic fluid-control devices. Through its enhanced microchannel design and use of pneumatic fluid-control devices, the microfluidic chip reduces the dead volume of the sample and increases the pumping rate. The maximum pumping rate of the developed micro-pump is 28 microL/min at an air pressure of 10 psi and a driving frequency of 10 Hz. The total sample volume consumed in each sensing operation is just 0.515 microL. As a result, the developed chip reduces the sample volume compared to conventional large-scale pH-sensing systems. The microfluidic chip employs the electrochemical sensing method to conduct precise pH level measurements. The sensing electrodes are fabricated by sputtering a layer of SiO(2)-LiO(2)-BaO-TiO(2)-La(2)O(3) (SLBTLO) onto platinum (Pt) electrodes and the pH value of the sample is evaluated by measuring the potential difference between the sensing electrodes and a reference electrode. Additionally, the integration of the microfluidic chip with a pneumatic fluid-control device facilitates automatic sample injection and a continuous sensing operation. The developed system provides a valuable tool with which to examine pH values in a wide range of biomedical and industrial applications.

Electrochemistry↗

PubMed2004

Telemetric electrochemical sensor.

A telemetric system was designed and constructed to sense pH and ethanol variation in aqueous solutions. The measured signals were transferred by software digitally and transmitted wirelessly by the telemeter, personal digital assistant (PDA), through the General Packet Radio Service (GPRS) protocol. The pH sensing electrode was designed to measure a chemical potential induced by a proton concentration gradient on the electrode's surface which exhibits internal Donnon diffusion behavior, and a linear relationship between the electrical potential and pH was found. The result shows that the wireless sensing system allowed not only long-term usage and long-distance transmission but also with high accuracy (e.g. S.D. less than +/-2%). The telemetric system can also be modified to measure ethanol concentration in aqueous solution amperometrically. It was found that the sensitivity of that ex situ measurements matched those of in field measurements with negligible deviation, less than 4%.

Cell Phone↗