Biomedical subjects

X F Peng

Publications and source records attributed to X F Peng.

8 recordsLinked to original sources

PubMed2006

Fluorecent staining for study of extracellular polymeric substances in membrane biofouling layers.

Membrane biofouling by microbial products adversely impacts the feasibility of adopting membrane bioreactors (MBRs) for treating wastewater. The fouling layer structure determines the pressure drop across the fouling layer. Three-dimensional distributions of nucleic acids, proteins, alpha-D-GLUCOPYRANOSE POLYSACCHARIDES, AND B-D-glucopyranose polysaccharides in the fouling layer formed on a mixed cellulose ester membrane were generated utilizing a quadruple staining protocol combined with confocal laser scanning microscopy (CLSM). For the first time, this study constructed a three-dimensional volumetric grids model representing the fouling layer structure on the basis of a series of CLSM images. Quantitative structural information about the fouling layer was extracted from the CLSM images.

Bacteria↗

PubMed2006

Micromechanics of wastewater sludge floc: force-deformation relationship at cyclic freezing and thawing.

This study examined shape changes in two typical wastewater flocs subjected to cyclic freezing and thawing and the associated force exerted by the ice front. While freezing, the engulfing ice front gradually pulled the floc apart. Subsequent thawing only partially restored the floc's shape. By the Maxwell model, used to interpret gross shape deformations, both flocs were visco-elastic objects exhibiting time-varying rheological characteristics which were more viscous than elastic. Detailed observations of floc 1 deformation demonstrated a two-stage force-displacement relationship. Following 1 cycle of freezing and thawing, the interior structure of the floc deteriorated and the force required to elongating a unit length of floc decreased by 60%. The original floc 2 had a dense "core" and loose "tail"; the core was more resistant to deformation under normal stress than the loose tail. Although both flocs had similar shapes and sizes and were acquired from the same activated sludge stream at a wastewater treatment plant, their rheological behaviors differed substantially. A comprehensive theoretical model for freezing and thawing processes should incorporate these rheological characteristics as they corresponded to observed structural changes and reduction in bound water content in sludge following a cyclic treatment of freezing and thawing.

Journal Article↗

PubMed2005

Diffusion coefficient of Brownian particle in rough micro-channel.

This study examines the feasibility of using of the lattice Boltzmann method to determine how the surface roughness of a quadrate channel affects the diffusion coefficient of Brownian particle(s). The surface was represented by a regular array of spheres. Surface roughness reduced the diffusion coefficient of the Brownian particle(s) because of a change in the velocity autocorrelation function decay and in pressure. Additionally, the neighboring particles increased the diffusion coefficient of Brownian particle.

Journal Article↗

PubMed2005

Fragmentation of wastewater sludge floc by planar ice front.

Floc size has substantial impact on sludge dewaterability, which might be increased or reduced after freezing and thawing. It is commonly assumed that floc size would be increased by low-speed freezing, with a planar ice front rejecting most flocs ahead of it to form large aggregates. We demonstrate in this work that an advancing planar ice front can not only engulf an activated sludge floc of size 3030 mum, but also fragment it. During floc freezing, when the ice engulfed a thin layer of floc, the latter would be pulled apart vertically by the action of the former. This particular portion of floc was then axially elongated and fixed in the frozen layer, with accumulated force pushing upward. In the present test the floc's vertical length was increased by over 92% and its width decreased by 37% over freezing. The force measurement and floc morphology tracking revealed that the force gradient that pulled apart the floc was 0.0027 N/m. The floc under investigation was fragmented at the point where the normal stress acting on the interior network exceeded 8 Pa.

Journal Article↗

PubMed2004

Force of a gas bubble on a foreign particle in front of a freezing interface.

We monitored the formation and development of a single gas bubble on the surface of a spherical particle of size 1.676 mm under unidirectional freezing and thawing (4.6-5.0 microm/s) and for the first time quantitatively estimated the force exerted on this particle by measuring the deformation of an attached elastic stick. The bubble would nucleate and grow on the particle surface closest to the ice front, while the force curve for a freezing-thawing cycle presented a hysteresis characteristic. This force was much greater than in the case without a bubble, and hence it dominated the engulfment process in the present freezing tests. The bubble force increased with increasing bubble size and was shown to be mainly attributable to the elastic force by the deformed bubble shape. Comments were made on the need to incorporate the role of bubbles in predicting the critical velocity to freeze a suspension with high dissolved gas content.

Journal Article↗

PubMed2004

Structure of conditioned sludge flocs.

Free settling tests, small-angle light scattering, microtome-slicing techniques, and confocal laser scanning microscopy were performed to examine how the cationic flocculation or freezing and thawing affected the floc structure. The floc size, internal pore size, mass fractal dimensions determined from free-settling test or small angle light scattering test, aeral porosity, boundary fractal dimension and Sierpinski carpet fractal dimension of pore boundary from 2D slices, and the volume porosity, compactness, and the pores' box-counting fractal dimension from 3D reconstructed image, were estimated and compared. Cationic flocculation would produce large flocs with internal pores of shape resembling a long "tube" with rough surface. Freezing and thawing would produce flocs with internal pores with lower aspect ratio and a smoother boundary.

Bacteria↗

PubMed2004

Thermal drying of wastewater sludge with crack formation.

We examined in this work the drying characteristics of wastewater sludge. The drying flux of the constant-rate period for sludge cake could be up to 40% higher than that from a sand bed. Owing to the considerable volume shrinkage of cake, cracks would form and develop on the crack surface, which yielded three-dimensional but rather than the one-dimensional cake structure assumed in conventional drying theories. The crack length was fully developed in the first 30 min of drying, while the width of crack increased linearly with time. Using these data the drying flux from the cracks was estimated. Enhanced drying flux was noticeable which depended on the crack shape and the crossflow velocity.

China↗

PubMed2002

Advective flow and floc permeability.

This work monitored advection flow through a floc by bubble tracking. Close examination of the motion of a swarm of hydrogen bubbles that passed over a free-falling floc allowed the extent of advection flow to be estimated at 53% for the original activated sludge floc, and 12% for the flocculated floc. The interior permeability of the sludge flocs was estimated from this information. The fluid force exerted on the falling floc was also considered.

Journal Article↗