Biomedical subjects

Xian-Ming Zeng

Publications and source records attributed to Xian-Ming Zeng.

5 recordsLinked to original sources

PubMed2006

Influence of realistic inspiratory flow profiles on fine particle fractions of dry powder aerosol formulations.

PURPOSE: The purpose of the study was to determine how air flow profiles affect fine particle fractions (FPF) (<5 microm) from dry powder aerosol formulations and whether laser diffraction (LD) could be used to measure FPF of aerosols generated by variable flows. MATERIALS AND METHODS: Carrier-based formulations containing 1.5% w/w micronized salbutamol base blended with the 63-90 microm fraction of alpha-lactose monohydrate or sorbitol or maltose were aerosolised from a model glass device using either a constant flow rate or a predetermined flow profile. The FPFs of the same aerosolised particles were first measured by LD and then by a liquid impinger. Volunteer inhalation airflow profiles and 3-phase (acceleration, constant flow rate and deceleration) square wave airflow profiles were generated using the Electronic Lung and an Inhalation Profile Recorder. Similar experiments were conducted for a carrier-free formulation from the Bricanyl Turbohaler. RESULTS: Salbutamol FPFs of all carrier-based formulations were found to increase by increasing the initial flow increase rate (FIR) from 200 to 600 l min(-1) s(-1) although they could be placed in an increasing order of maltose blend < sorbitol blend < lactose blend. A significant linear correlation was found between FPFs measured by LD and by inertial impaction (R (2) = 0.95, p < 0.01, ANOVA). For the Bricanyl Turbohaler, increasing FIR from 120 to 600 l min(-1) s(-1) for a constant peak flow rate (PFR) of 60 l min(-1) increased the mean Terbutaline FPF from 18.2% to 45.5%. For the volunteer inhalation profiles, a higher FIR tended to be associated with higher PFR, leading to a marked increase in drug FPF due to the combined effect of FIR and PFR. CONCLUSION: Drug FPF from either carrier-free or carrier-based formulations is determined by both FIR and PFR. LD is a viable technique to measure the performance of dry powder aerosol formulations at realistic inspiratory flow profiles.

Administration, Inhalation↗

PubMed2006

Humidity-induced changes of the aerodynamic properties of dry powder aerosol formulations containing different carriers.

This paper presents the findings of two related studies. The aim of the first was to study any changes in the aerodynamic properties of salbutamol base powder formulations when different sugars were used as the carriers, after storage at an elevated humidity (75% RH), and whether any such changes (if any) were related to the physical properties of the carriers. The aim of the second was to investigate whether "ageing", i.e. storage of the carrier, drug and blends under desiccation for more than 2 years, affected the aerodynamic properties of salbutamol sulphate powder formulations. Different formulations were prepared, each containing 1.5% (w/w) micronised salbutamol base or sulphate blended with the sieved fraction (63-90 microm) of one of the following sugars: alpha lactose monohydrate, sorbitol, maltose and dextrose. The salbutamol base blends were then stored unprotected at 75% RH (ambient temperature) and salbutamol fine particle fractions (FPFs) were measured by laser diffraction (LD) (% < 5.2 microm) and a multistage liquid impinger (MSLI) (% < 5.3 microm), following aerosolisation at 100 l min(-1) from a model glass inhaler, after storage of each formulation at the elevated conditions for 0, 1 and 6 days. Particle morphology and equilibrium moisture content (EMC) of each formulation prior to and after storage were also evaluated. However, the salbutamol sulphate blends containing either "fresh" or "aged" components were only characterized using LD at 60 l min(-1). Prior to exposure to 75% RH, the lactose blend was found to give the highest FPF of salbutamol (30% by LD and 37% by MSLI), followed by the sorbitol blend (17% by LD and 29% by MSLI), then by the dextrose blend (15% by LD and 25% by MSLI) and finally by the maltose blend (13% by LD and 13% by MSLI). Exposure to 75% RH for 6 days resulted in a small reduction of salbutamol FPF from the lactose blend but drastic diminution of salbutamol FPFs from other blends. After exposure to the high RH, the lactose blend adsorbed ca. 0.4% whilst each of the other sugars took up larger quantities of water (15-40%) and underwent a marked change in the surface texture of the particles. "Ageing" of the carriers and/or formulations did not seem to alter the aerodynamic properties of the drug. "Ageing" of micronised salbutamol sulphate prior to blending, however, was found to improve the FPF of drug. LD was capable of detecting subtle differences between the various formulations and generated FPF results that correlated with those measured by MSLI.

Administration, Inhalation↗

PubMed2006

Correlation between inertial impaction and laser diffraction sizing data for aerosolized carrier-based dry powder formulations.

PURPOSE: The purpose of the study was to determine whether the drug fine particle fraction (FPF) from different dry powder aerosol formulations measured by laser diffraction at a range of flow rates correlated with that measured by inertial impaction. MATERIALS AND METHODS: Ten binary formulations were prepared containing 1.5% w/w salbutamol base or sulphate, blended with the sieved (63-90 microm) fraction of different sugars (regular lactose, spray-dried lactose, sorbitol, dextrose or maltose). A further six ternary formulations were prepared containing 1.5% w/w salbutamol sulphate, 97% coarse lactose (63-90 microm) and 1.5% micronised or intermediate-sized lactose (1-50 microm). The FPF particles (< 5 microm) of these formulations were measured by laser diffraction and inertial impaction at flow rates between 28.3 and 100 l min(-1). RESULTS: When only the particles with diameter < 60 microm obtained by laser diffraction were considered the FPF (< 5 microm) could be determined and this enabled the aerosolisation of all 16 blends to be feasibly compared at flow rates ranging from 28.3 to 100 l min(-1). A significant linear correlation was found between the fine fractions measured by laser diffraction and the salbutamol fine fractions determined by inertial impaction (r2 = 0.934). Such correlation was also confirmed for formulations containing added fine lactose. CONCLUSION: Particle size measured by laser diffraction under the employed conditions reflected the aerodynamic properties of the drug. Laser diffraction can be used as on-, in- and/or at-line measurements and controls for dry powder aerosol formulations.

Adrenergic beta-Agonists↗

PubMed2006

Characterisation of a carrier-free dry powder aerosol formulation using inertial impaction and laser diffraction.

PURPOSE: The purpose of the study was to examine the suitability of using laser diffraction to measure the fine particle fraction (FPF) of drugs emitted from carrier-free dry powder aerosol formulations. MATERIALS AND METHODS: Particle size distribution of terbutaline sulphate from Bricanyl Turbohaler, which contained loose agglomerates of drug particles only, was measured separately by laser diffraction apparatus equipped with a metal throat and a twin-stage, multi-stage liquid impingers, or Andersen cascade impactor at flow rates ranging from 28.3 to 100 l min(-1). In-line measurements were then conducted which allowed the same aerosolised particles to be measured first by laser diffraction then captured by an impactor or impinger for subsequent chemical analysis. RESULTS: A significant linear correlation (p < 0.001, R2 = 0.96, ANOVA) existed between the results obtained from two techniques when measurements were conducted independently. There was little difference in FPFs measured by inertial impaction and laser diffraction at the same flow rate. When in-line measurements were conducted, the FPFs measured by inertial impaction were approximately 0.7-0.9 times the aerosol FPFs measured by laser diffraction. This linear relationship was statistically significant and had a statistically insignificant y-intercept, regardless of inhaler batches, impinger types and measuring position of the laser beam. CONCLUSION: Laser diffraction could prove to be a reliable technique for development, evaluation and quality control of carrier-free, dry powder aerosol formulations.

Aerosols↗

PubMed2006

Development of a laser diffraction method for the determination of the particle size of aerosolised powder formulations.

Impactor data are an essential component of marketing authorisation for new dry powder aerosol formulations. However such data are time-consuming to obtain and therefore impede the rapid screening of pilot formulations. In this phase of development it would be of considerable benefit to employ a technique where data acquisition was more rapid, such as laser diffraction, to predict the fine particle fraction. It was the aim of this study to investigate whether this is a feasible premise. Five different formulations were prepared, each containing 1.5% (w/w) micronised salbutamol base (volume median diameter: 2.42 microm) blended with the sieved fraction (63-90 microm) of one of the following sugars: regular crystalline lactose, spray dried lactose "Zeparox", sorbitol, maltose and dextrose monohydrate. A Perspex box was constructed to contain particles released from a glass inhaler and allow the particles to be measured by laser diffraction at different flow rates. After being validated using monodisperse aerosols, this assembly was then employed to measure the particle size distributions of each powder formulation and its respective sugar carrier at flow rates ranging from 28.3 to 100 l min(-1). Aerodynamic particle size distribution of salbutamol base from each formulation was also measured after aerosolisation at 28.3 l min(-1) from the glass inhaler into an Andersen cascade impactor. The flight of monodisperse particles with diameters (2-6 microm) in the desired size range of dry powders for inhalation could be contained and the size distribution determined by laser diffraction using the assembly at all flow rates investigated. Treatment of the particle size distributions measured by laser diffraction, i.e. examining only the aerosol particles with diameter <60 microm, highlighted the fine fraction (<5 microm) and enabled the aerosolisation of different blends to be feasibly compared at a range of different flow rates. The blends containing the following excipients could be placed in the following order of increasing fine fraction: spray-dried lactose<dextrose<<maltose<lactose<sorbitol. At 28.3 l min(-1) a significant linear correlation was found between the fine fractions measured by laser diffraction and the salbutamol fine fractions determined by inertial impaction (R(2)=87.4%, p=0.02, ANOVA). Therefore, the laser diffraction technique could prove to be an important tool for particle size characterisation of dry powder aerosol formulations.

Aerosols↗