Biomedical subjects

Xiurong Yang

Publications and source records attributed to Xiurong Yang.

At least 19 recordsLinked to original sources

PubMed2006

Synthesis of PtNPs/AQ/Ru(bpy)3(2+) colloid and its application as a sensitive solid-state electrochemiluminescence sensor material.

The facile synthesis of the novel platinum nanoparticles/Eastman AQ55D/ruthenium(II) tris(bipyridine) (PtNPs/AQ/Ru(bpy)3(2+)) colloidal material for ultrasensitive ECL solid-state sensors was reported for the first time. The cation ion-exchanger AQ was used not only to immobilize ECL active species Ru(bpy)3(2+) but also as the dispersant of PtNPs. Colloidal characterization was accomplished by transmission electron microscopy (TEM), X-ray photoelectron spectrum (XPS), and UV-vis spectroscopy. Directly coating the as-prepared colloid on the surface of a glassy carbon electrode produces an electrochemiluminescence (ECL) sensor. The electronic conductivity and electroactivity of PtNPs in composite film made the sensor exhibit faster electron transfer, higher ECL intensity of Ru(bpy)3(2+), and a shorter equilibration time than Ru(bpy)3(2+) immobilized in pure AQ film. Furthermore, it was demonstrated that the combination of PtNPs and permselective cation exchanger made the sensor exhibite excellent ECL behavior and stability and a very low limit of detection (1 x 10(-15) M) of tripropylamine with application prospects in bioanalysis. This method was very simple, effective, and low cost.

Journal Article↗

PubMed2006

Electrochemical impedance detection of DNA hybridization based on dendrimer modified electrode.

Bioactive ultrathin films with the incorporation of amino-terminated G4 PAMAM dendrimers have been prepared via layer-by-layer self-assembly methods on a gold electrode and used for the DNA hybridization analysis. Surface plasmon resonance (SPR), X-ray photoelectron spectroscopy (XPS), and electrochemical impedance spectroscopy (EIS) are used to characterize the successful construction of the multicomponent film on the gold substrate. The dendrimer-modified surfaces improve the immobilization capacity of the probe DNA greatly, compared to the AET (2-aminoethanethiol) SAM sensor surfaces without dendrimer molecules. DNA hybridization analysis is monitored by EIS. The dendrimer-based electrochemical impedance DNA biosensor shows high sensitivity and selectivity for DNA hybridization assay. The multicomponent films also display a high stability during repeated regeneration and hybridization cycles.

Biosensing Techniques↗

PubMed2006

Polyamidoamine dendrimers-assisted electrodeposition of gold-platinum bimetallic nanoflowers.

Novel Au-Pt bimetallic flower nanostructures fabricated on a polyamidoamine dendrimers-modified surface by electrodeposition are reported. These polyamidoamine dendrimers were stable, and they assisted the formation of Au-Pt bimetallic nanoflowers during the electrodeposition process. These nanoflowers were characterized by field-emitted scanning electron microscopy (FE-SEM), energy-dispersive spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction, and electrochemical methods. FE-SEM images showed that the bimetallic nanoflower included two parts: the "light" and the "pale" part. The two parts consisted of many small bimetallic nanoparticles, which was attributed to the progressive nucleation process. Moreover, the "light" part contained more bimetallic nanoparticles. The morphologies of bimetallic nanoflowers depended on the electrodeposition time and potential and the layer number of assembled dendrimers. The average size of nanoflowers increased with the increase in electrodeposition time. The layer number of assembled dendrimers obviously affected the size and morphologies of the "pale" parts of deposited nanoflowers. EDS and XPS indicated that the content of Au element was higher than that of Pt element in the nanoflowers. The bimetallic nanoflowers-modified electrode had electrochemical properties similar to those of bare gold and platinum electrodes. It also exhibited significant electrocatalytic activities toward oxygen reduction.

Amides↗

PubMed2006

Specific determination of As(V) by an acid phosphatase-polyphenol oxidase biosensor.

An original amperometric biosensor based on the simultaneous entrapment of acid phosphatase (AcP) and polyphenol oxidase (PPO) into anionic clays (layered double hydroxides) was developed for the specific detection of As(V). The functioning principle of the bienzyme electrode consisted of the successive hydrolysis of phenyl phosphate into phenol by AcP, followed by the oxidation of phenol into o-quinone by PPO. The phenyl phosphate concentration was, thus, monitored by potentiostating the biosensor at -0.2 V vs Ag/AgCl to detect amperometrically the generated quinone. The detection of As(V) was based on its inhibitory effect on AcP activity toward the hydrolysis of phenyl phosphate into phenol. The As(V) can be specifically determined in pH 6.0 acetate buffer without any interferences of As(III) or phosphate, the detection limit being 2 nM or 0.15 ppb after an incubation step for 20 min.

Acid Phosphatase↗

PubMed2006

Application of electrochemical impedance spectroscopy for monitoring allergen-antibody reactions using gold nanoparticle-based biomolecular immobilization method.

Gold nanoparticles were used to enhance the immobilization amount and retain the immunoactivity of recombinant dust mite allergen Der f2 immobilized on a glassy carbon electrode (GCE). The interaction between allergen and antibody was studied by electrochemical impedance spectroscopy (EIS). Self-assembled Au colloid layer (ø=16nm) deposited on (3-mercaptopropyl)trimethoxysilane (MPTS)-modified GCE offered a basis to control the immobilization of allergen Der f2. The impedance measurements were based on the charge transfer kinetics of the [Fe(CN)(6)](3-/4-) redox pair, compared with bare GCE, the immobilization of allergen Der f2 and the allergen-antibody interaction that occurred on the electrode surface altered the interfacial electron transfer resistance and thereby slowed down the charge transfer kinetics by reducing the active area of the electrode or by preventing the redox species in electrolyte solution from approaching the electrode. The interactions of allergen with various concentrations of monoclonal antibody were also monitored through the change of impedance response. The results showed that the electron transfer resistance increased with increasing concentrations of monoclonal antibody.

Allergens↗

PubMed2006

Characterization of prolidase activity using capillary electrophoresis with tris(2,2'-bipyridyl)ruthenium(II) electrochemiluminescence detection and application to evaluate collagen degradation in diabetes mellitus.

A new method for prolidase (PLD, EC 3.4.13.9) activity assay was developed based on the determination of proline produced from enzymatic reaction through capillary electrophoresis (CE) with tris(2,2'-bipyridyl)ruthenium(II) [Ru(bpy)3(2+)] electrochemiluminescence detection (ECL). A detection limit of 12.2 fmol (S/N = 3) for proline, corresponding to 1.22 x 10(-8) units of prolidase catalyzing for 1 min was achieved. PLD activity determined by CE-ECL method was in agreement with that obtained from the classical Chinard's one. CE-ECL showed its powerful resolving ability and selectivity as no sample pretreatment was needed and no interference existed. The clinical utility of this method was successfully demonstrated by its application to assay PLD activity in the serum of diabetic patients in order to evaluate collagen degradation in diabetes mellitus (DM). The results indicated that enhanced collagen degradation occurred in DM.

2,2'-Dipyridyl↗

PubMed2006

Buildup of gold nanoparticle multilayer thin films based on the covalent-bonding interaction between boronic acids and polyols.

A novel method for the fabrication of gold nanoparticle multilayer films based on the covalent-bonding interaction between boronic acid and polyols, poly(vinyl alcohol) (PVA), was developed. The multilayer buildup was monitored by UV-vis absorbance spectroscopy, which showed a linear increase of the film absorbance with the number of adsorbed Au layers and indicated the stepwise and uniform assembling process. The atomic force microscopy (AFM) image showed that a compact gold multilayer thin film was successfully assembled. The residual boronic acid group on the surface of thin film could incorporate glycosylated-protein horseradish peroxidase (HRP), and good catalytic activity for H2O2 could be observed.

Boronic Acids↗

PubMed2006

CE coupling with end-column electrochemiluminescence detection for chiral separation of disopyramide.

CE with electrochemiluminescence (ECL) detection technique was successfully applied for the chiral separation of a kind of class IA antiarrhythmic racemic drug. To the best of our knowledge, this is the first report of ECL detection used in chiral CE. To get better detection sensitivity and good enantioresolution at the same time, the conditions of capillary inlet and outlet buffer were systematically optimized. Unlike the traditional chiral separation method, the buffers we used in the capillary inlet and outlet differed from each other in terms of buffer pH, ionic strength, type of BGE as well as buffer composition. Under the optimum conditions, baseline enantioseparation and highly sensitive detection of the enantiomers were achieved. Wide linear relationship of each enantiomer was achieved in the range of 5 x 10(-7) to 2 x 10(-5) mol/L with relative coefficients of 0.996 and 0.997, respectively. The detection limits were estimated to be 8 x 10(-8) and 1.0 x 10(-7) mol/L (S/N = 3) for the enantiomers, respectively. In addition, a successful application of this new method to the chiral separation of the racemic drug in spiked plasma samples confirmed the validity and applicability of the chiral CE-ECL method.

Anti-Arrhythmia Agents↗

PubMed2006

Kinetic study of paracetamol on prolidase activity in erythrocytes by capillary electrophoresis with Ru(bpy)(3) (2+) electrochemiluminescence detection.

We explored the CE with (bpy) (2+) (3) electrochemiluminescence detection for the kinetic study of drug-enzyme interaction. Effects of four nonsteroidal anti-inflammatory drugs including aspirin, paracetamol, sodium salicylate and phenacetin on prolidase (PLD) activity in erythrocytes were investigated. Aspirin enhanced PLD activity whereas the other three had inhibiting effects. This may reveal their different effects on the collagen biosynthesis and catabolism that influence tumor invasiveness. Kinetic study of paracetamol on PLD showed that the value of Michaelis constant K(m) for PLD was 1.23 mM. The mechanism of PLD inhibition by paracetamol is noncompetitive inhibition, and the inhibitor constant K(i) value obtained in our research was 9.73 x 10(3) microg/L.

Acetaminophen↗

PubMed2006

Novel prefractionation method can be used in proteomic analysis.

For the first time, a novel prefractionation method used in proteomic analysis was developed, which is performed by a novel aqueous two-phase system (NATPS) composed of n-butanol, (NH(4))(2)SO(4), and water. It can separate proteomic proteins into multigroups by one-step extraction. The phase-separation conditions of n-butanol solutions were studied in the presence of commonly used inorganic salts. The NATPS was subsequently developed. Using human serum albumin, zein, and gamma-globulin as model proteins, the separation effectiveness of the NATPS for protein was studied under affection factors, i.e., pH, n-butanol volume, protein, or salt concentration. The model and actual protein samples were separated by the NATPS and then directly used for gel electrophoresis without separating the target proteins from phase-forming reagents. It revealed that the NATPS could separate proteomic proteins into multigroups by one-step extraction. The NATPS has the advantages of rapidity, simplicity, low cost, biocompability, and high efficiency. It need not separate target proteins from the phase-forming reagents. The NATPS has great significance in separation and extraction of proteomic proteins, as well as in methodology.

1-Butanol↗

PubMed2005

Microchip capillary electrophoresis with solid-state electrochemiluminescence detector.

We report microchip capillary electrophoresis (CE) coupling to a solid-state electrochemiluminescence (ECL) detector. The solid-state ECL detector was fabricated by immobilizing tris(2,2'-bipyridyl)ruthenium(II) (TBR) into an Eastman AQ55D-silica-carbon nanotube composite thin film on an indium tin oxide (ITO) electrode. After being made by a photolithographic method, the surface of the ITO electrode was coated with a thin composite film through a micromolding in capillary (MIMIC) technique using a poly(dimethylsiloxane) (PDMS) microchannel with the same pattern as an ITO electrode. Then the TBR was immobilized via ion exchange by immersing the ITO electrode containing the thin film in TBR aqueous solution. The whole system was built by reversibly sealing the TBR-modified ITO electrode plate with a PDMS layer containing electrophoresis microchannels. The results indicated that the present solid-state ECL detector displayed good durability and stability in the microchip CE-ECL system. Proline was selected to perform the microchip device with a limit of detection of 2 microM (S/N=3) and a linear range from 25 to 1000 microM. Compared with the CE-ECL of TBR in aqueous solution, while the CE microchip with solid-state ECL detector system gave the same sensitivity of analysis, a much lower TBR consumption and a high integration of the whole system were obtained. The present system was also used for medicine analysis.

9,10-Dimethyl-1,2-benzanthracene↗

PubMed2005

Morphology-controlled synthesis of monodisperse ZnO troughs at the air-water interface under mild conditions.

In this work, an interfacial synthetic strategy to produce ZnO troughs at the air-water interface under mild conditions was demonstrated. The as-prepared ZnO trough was monodisperse, single crystalline, and pure. By manipulation of the magnet stirring time, the fabricated ZnO can be manipulated as an independent or intertwined trough. Various preparative parameters, such as initial reactants and their concentrations, had been examined, and the results revealed that troughlike ZnO could be only obtained by adopting zinc acetate and hexamethylenetetramine as precursors at concentrations larger than 0.01 M. The as-obtained ZnO, within the dimension of several micrometers, showed a trough-related photoluminescence emission at 356 nm. Moreover, the evolution process of a ZnO trough after reaction for 5, 30, 60, and 90 min was viewed by X-ray diffraction and field emission scanning electron microscopy characterization, and a possible mechanism was also proposed and discussed, which might help us to further our understanding toward the reaction mechanism at the air-water interface.

Air↗

PubMed2005

Microfluidic chip with electrochemiluminescence detection using 2-(2-aminoethyl)-1-methylpyrrolidine labeling.

A tertiary amine derivative, 2-(2-aminoethyl)-1-methylpyrrolidine (AEMP) was successfully developed as electrochemiluminescence (ECL) probe within microfluidic chip using ECL detection in this paper. The system was characterized by the interaction between biotin and avidin. In principle, tertiary amine derivatives containing active group can be used as a potential alternative of traditional tris(2,2'-bipyridine)ruthenium(II) [Ru(bpy)3(2+)] label. Firstly, The ECL efficiency of AEMP was characterized via comparing with that of two coreactants enhancing Ru(bpy)3(2+) ECL, TPA and proline. At same condition, AEMP has a similar ECL efficiency to TPA, and much higher than proline. After AEMP reacted with NHS-LC-biotin (succinimidyl-6-(biotinamido) hexanoate), the products and their ECL were analyzed by directly injecting it in the microfluidic chip. A 4.5 cm microchannel was used to separate the mixture of AEMP and biotinylated AEMP. The present works indicated that AEMP has a good reactivity to the analytes containing carboxyl group with a similar ECL efficiency to TPA. Under optimal condition, the detection limits (based on 3 S/N) of AEMP was 2.7 microM. The system was also validated by the reaction between biotin and avidin. The calculated binding ratio between avidin and biotin based on the present method was 4.4.

Aminocaproates↗

PubMed2005

Fabrication of a poly(dimethylsiloxane)-based electrochemiluminescence detection cell for capillary electrophoresis.

An easy but effective technique is described here for quick fabrication of low-cost electrochemiluminescence detection cells for capillary electrophoresis. The technique is based on molding of poly(dimethylsiloxane) (PDMS) with a capillary column inserted into a pipet tip. Two access holes are left in the PDMS slab; they provide neat accommodations for the separation capillary and the working electrode made with the same type of tip. Since the access holes are well-aligned, the electrode and the capillary are automatically aligned; thus, end-column detection is easily obtained. Fabrication of the detection cell is straightforward; no micromechanical operation is included. Also the principle for the procedure makes it possible to efficiently batch production detection cells with good reproducibility. Because of the end-column scheme, the cell can be adopted for electrophoresis with electrochemical detection as well.

Journal Article↗

PubMed2005

Interaction of anticancer drug mitoxantrone with DNA analyzed by electrochemical and spectroscopic methods.

Cyclic voltammetry coupled with different spectroscopic (UV/Vis, fluorescence and Raman) techniques were used to study the interaction of mitoxantrone (MTX), an antitumor drug, with calf thymus DNA in acetate buffer solutions (pH 4.5). The interaction of MTX with DNA could result a considerable decrease in the MTX peak currents and a hypochromic and bathochromic shift in the maximum adsorption bands of MTX as well as the emission quenching in the MTX fluorescence spectra. The variations in the electrochemical and spectral characteristics of MTX indicated MTX bind to DNA by an intercalative mode. This conclusion was reinforced by Raman data. The merely particular vibrations were affected in Raman, suggesting that only a portion of the chromophore of MTX was involved in the intercalation into DNA duplex. These studies are valuable for a better understanding the detailed mode of MTX-DNA interaction, which should be important in deeper insight into the therapeutic efficacy of MTX and design of new DNA targeted drug.

Animals↗

PubMed2005

Promoted electron transfer of mitoxantrone binding with DNA by cytochrome c.

A promoted electron transfer of an antitumor drug, mitoxantrone (MTX), intercalating into DNA duplex was successfully obtained upon addition of cytochromes c (cyt. c) in NaAc-HAc buffer solution (pH 4.5). The experimental results suggested that co-existence of MTX and cyt. c in the DNA helix is an important factor for accelerated electron transfer of MTX, where the promoter, cyt. c, operated smoothly through the DNA bridge. The UV/Vis spectroscopic experiments further confirmed the interaction process. Furthermore, a possible mechanism of such reaction was also discussed in this paper.

Cytochromes c↗

PubMed2005

4-(Dimethylamino)butyric acid labeling for electrochemiluminescence detection of biological substances by increasing sensitivity with gold nanoparticle amplification.

4-(Dimethylamino)butyric acid (DMBA) labeling combined with gold nanoparticle amplification for electrochemiluminescence (ECL) determination of a biological substance (bovine serum albumin (BSA) and immunoglobulin G (IgG) as models) was presented. After DMBA, an analogue of tripropylamine, was tagged on the (anti)analytes, an ECL signal related to the content of the analytes was generated when the analyte tagged with DMBA was in contact with tris(2,2'-bipyridine)ruthenium (Ru(bpy)(3)2+) solution and a potential was applied. To improve the adsorption capacity, a gold nanoparticle layer was first combined into the surface of the 2-mm-diameter gold electrode. For the determination of BSA, avidin was covalently conjugated to a self-assembled monolayer of 3-mercaptopropanoic acid on the gold nanoparticle layer. Biotinylated BSA-DMBA was then immobilized on the gold nanoparticle layer of the gold electrode via the avidin-biotin reaction. IgG was tested via a typical sandwich-type immobilization method. ECL signals were generated from the electrodes immobilized with BSA or IgG by immersing them in a 1 mmol L-1 Ru(bpy)(3)2+ solution and scanning from 0.5 to 1.3 V versus Ag/AgCl. With gold nanoparticle amplification, the ECL peak intensity was proportional to the concentration over the range 1-80 and 5-100 microg/mL for BSA and IgG consuming 50 microL of sample, respectively. A 10- and 6-fold sensitivity enhancement was obtained for BSA and IgG over their direct immobilization on an electrode using DMBA labeling. The relative standard deviations of five replicate determinations of 10 microg/mL BSA and 20 microg/mL IgG were 8.4 and 10.2%, respectively. High biocompatibility and low cost were the main advantages of the present DMBA labeling technique over the traditional Ru(bpy)(3)2+ labeling.

2,2'-Dipyridyl↗

PubMed2005

One-step synthesis of amino-dextran-protected gold and silver nanoparticles and its application in biosensors.

A sensitive method for the detection of the lectin protein concanavalin A (Con A) was developed using amino-dextran (AD)-protected gold (AD-Au) and silver nanoparticles (AD-Ag) as sensitive optical probes. The AD-Au and AD-Ag nanoparticles were synthesized by directly applying amino-dextran as a reductive and protective reagent. The size of the nanoparticles could be altered by changing the molar ratio of AD to the metal salt. The amino-dextran bound to Con A by forming a 4:1 Au-Con A complex at neutral pH, and the nanoparticles were induced to aggregate by Con A. The absorption intensity of the nanoparticles decreased linearly with as the Con A concentration was increased from 3.85 x 10(-8) to 6.15 x 10(-7) M. The Au-Con A complex was dissociated by the disaccharide isomaltose, which has a higher affinities for Con A than Au; this competitive strategy could also be used to detect similar types of saccharides.

Biosensing Techniques↗