Biomedical subjects

Y T Zhu

Publications and source records attributed to Y T Zhu.

5 recordsLinked to original sources

PubMed2005

Compact and dissociated dislocations in aluminum: implications for deformation.

Atomistic simulations, confirmed by electron microscopy, show that dislocations in aluminum can have compact or dissociated cores. The calculated minimum stress (sigma(P)) required to move an edge dislocation is approximately 20 times smaller for dissociated than for equivalent compact dislocations. This contradicts the well accepted generalized stacking fault energy paradigm that predicts similar sigma(P) values for both configurations. Additionally, Frank's rule and the Schmid law are also violated because dislocation core energies become important. These results may help settle a 50-year-old puzzle regarding the magnitude of sigma(P) in face-centered-cubic metals, and provide new insights into the deformation of ultra-fine-grained metals.

Journal Article↗

PubMed2004

Ultralong single-wall carbon nanotubes.

Since the discovery of carbon nanotubes in 1991 by Iijima, there has been great interest in creating long, continuous nanotubes for applications where their properties coupled with extended lengths will enable new technology developments. For example, ultralong nanotubes can be spun into fibres that are more than an order of magnitude stronger than any current structural material, allowing revolutionary advances in lightweight, high-strength applications. Long metallic nanotubes will enable new types of micro-electromechanical systems such as micro-electric motors, and can also act as a nanoconducting cable for wiring micro-electronic devices. Here we report the synthesis of 4-cm-long individual single-wall carbon nanotubes (SWNTs) at a high growth rate of 11 microm s(-1) by catalytic chemical vapour deposition. Our results suggest the possibility of growing SWNTs continuously without any apparent length limitation.

Microscopy, Atomic Force↗

PubMed2001

Microstructures and properties of ultrafine-grained pure titanium processed by equal-channel angular pressing and cold deformation.

Equal-channel angular pressing (ECAP) has been used to refine the grain size of commercially pure (CP) titanium as well as other metals and alloys. CP-Ti is usually processed at about 400 degrees C because it lacks sufficient ductility at lower temperature. The warm processing temperature limits the ability of the ECAP technique to improve the strength of CP-Ti. We have employed cold deformation following warm ECAP to further improve the strength of CP-Ti. Ti billets were first processed for eight passes via ECAP route Bc, with a clockwise rotation of 90 degrees between adjacent passes. The grain size obtained by ECAP alone is about 260 nm. The billets were further processed by cold deformation (cold rolling) to increase the crystalline defects such as dislocations. The strength of pure Ti was improved from 380 to around 1000 MPa by the two-step process. This article reports the microstructures, microhardness, tensile properties, and thermal stability of these Ti billets processed by a combination of ECAP and cold deformation.

Cold Temperature↗

PubMed1981

Studies on mechanism of action of luteinizing releasing hormone (LH-RH) in ovulation of fish--intracellular distribution of LH-RH-A in pituitary gonadotrophs as revealed by electron-microscopic autoradiography.

The results of competitive bending experiment and the electron-microscopic autoradiographic studies show that the peptide hormone, LH-RH-A (a nonapeptide), could be internalized into the gonadotrophs of the pituitary gland of the mud-carp (Cirrhrinus molitorella). It is demonstrated that the labeled peptide, 125I-LH-RH-A, is internalized not only into the cytoplasm, but also into the nucleus, apparently via the nuclear pores. It is, therefore, suggested that the peptide hormone might act directly on the genome either in the form of a hormone-receptor complex or of a single molecule.

Animals↗

PubMedDate not supplied

Formation of pile networks by long carbon nanotubes from decomposition of CO on Co-Mo film.

We report the formation of pile networks by long carbon nanotubes grown at 700 degrees C from a Co-Mo film on a quartz plate. Carbon monoxide (CO) was used as the carbon source. The networks were formed because the density of catalyst particles on the substrate was low, which resulted in low carbon nanotube density that did not support vertical growth. At the same time, the low carbon nanotube density makes it possible for CO to reach the catalysts on the substrate for continuous growth. No obvious amorphous carbon chunks were observed, suggesting that the pile networks consisted of fairly high-quality, long carbon nanotubes.

Adsorption↗